Cannot be charged from non-certified cables. This cable or accessory is not certified or supported

Youtube

Producing charging iPad or iPhone using a Lightning connector, the device may display a message that reads: " This accessory or the cable is not certified, so its reliability with iPhone data not guaranteed." After this, charging will stop.

There are several reasons for this “strange” behavior of the gadget. But, before you start looking for them, you need to disconnect and then reconnect the cable to the Lightning connector. In addition, you can solve the charging problem by connecting to another USB port or to another outlet. But if positive result no, it means the problem is hidden deeper.

Increase

Non-original accessories

Reason for appearance similar message- use of non-original accessories. Branded products are more expensive than “analogs” from unknown manufacturers. It happens that such things work well, and sometimes they flatly refuse to function.

As always, such protection of apple manufacturers can be bypassed. To do this, follow these steps:

connect the cable to your iPhone or iPad;
after the unfortunate message appears, click “Close”;
unlock the device;
When the message appears, click “Close” again;
without blocking, pull out the cable from the device connector;
connect the cable again.

Much the best option is to purchase a cable that will work well and will not damage your expensive gadget. There are alternative inexpensive but high-quality accessories from third-party manufacturers. On their packaging you can see the inscription “ Made for iPhone / iPod / iPad.”

Damaged cable and debris

The cable may refuse to work due to a simple breakdown. The accessory may have gotten wet, corroded, or received physical damage. You will have to buy a new one, because such things cannot be repaired.

This is the most easily resolved cause of the cable support failure message. Debris is a physical hindrance to the charging process. Such cases are rare, but still occur. Threads, lint, crumbs, or other particles that are located at the bottom of the pocket may become trapped in the port. To solve this problem, you need to check the ports and, if necessary, carefully remove any debris stuck there.

Comrades from the United States of America are increasingly fighting for copyrights. In the bourgeoisie, licensing is held in high esteem, as well as only original gadgets and devices. Therefore, the appearance of errors and warnings about certification of cables and accessories not news for the owner of an iPhone, iPad or iPod.

World Famous Apple company went further than others in this. Starting with the new, seventh generation of operating iOS systems, the ability to connect a smartphone or tablet using cheap Chinese USB cables has disappeared. When connecting a non-original cord, a message appears that This cable or accessory is not certified and may not work correctly with this device.. At the same time, if in beta versions of the system the gadget simply warned about the problem, now it blocks the unwanted cable.

There are three workarounds for the error if the message appears: “ This cable or the accessory is not certified.”

1) The simplest, but also unreliable. This method doesn't always work. But you don’t need to make any special efforts to try it.

You should connect your phone to the network using a USB cable.
Click “close” when an error message appears.
Unlock the gadget and press the same button in the warning window.
Disconnect the cable from the network and then connect it back.
Click the “close” button again in the message about an uncertified cable.

The gadget will start charging. This method is explained by a bug in the device’s firmware and does not always work, but over time, Apple developers will be able to eliminate this trick.

2) Buy a special Chinese cable. The Celestial Empire is rich in so many talents. And now, craftsmen from China have managed to develop a cable that is not afraid of being blocked by an iPhone or iPad. The creators claim that usb type completely unimportant for their models; cords work equally well with all types of gadgets. How long Chinese new generation cables will be able to stay on the market is unknown. After all, Apple is also not standing still and will want to improve the program code to protect against fraudsters.

3) The most difficult, but this moment most effective method. The Cydia store has released a special free tweak that will help you bypass the protection.

First, you need to jailbreak using the Evasi0n 7 utility. Instructions for working with it can be found on the Internet.
Next you should run with home screen Cydia and wait for the storage update. In the Manage tab, click on the Source button.
Add the following Internet address - http://parrotgeek.net/repo. The program will automatically download all the necessary data from the storage.
Find a tweak called Unauthorized Lightning Cable Enabler.
Update your device for the changes to take effect.

After these simple manipulations, the gadget will begin to charge even with the help of non-certified cables and accessories. This method is good because during beta testing of the seventh generation of iOS, it was in the shadows. And only after the official release operating system, the tweak appeared in public access. Consequently, Apple was unable to block the program's actions even before the system was released. It is possible that they will now add such a function to new version firmware. But folk craftsmen will come up with something new. As always happens in the struggle between pirates and copyright holders.

China rules! But not in this case and here's why.

In the comments on our site, readers are still asking questions related to the use of USB cables for iPhone and iPad. Some people complain that a message appears on or on the smartphone screen stating that “this cable or accessory is not supported or certified.” In this case, the device does not charge and does not synchronize, restore or updating the gadget also fails. Why do Apple smartphones and tablets not like some USB cables and what can be done about it?

These messages first appeared in iOS 7 on the iPhone 5 - “This accessory may not be supported.” On iOS 8 or later later versions The content of the message has been slightly changed - “This cable or accessory is not certified and therefore is not guaranteed to work reliably with this iPhone.” There are several reasons:

1. You are using a non-original and non-certified USB cable.

The Lightning connector only looks simple from the outside; under its shell there is a microcircuit with 4 microchips. We don’t fully know how they work and what a particular one is intended for, but it is reliably known that this controller:

Switches the contacts to which the iPhone is connected - the Lightning connector is double-sided and is inserted into the connector on either side.
Responsible for the secure transfer of information between the device and the computer when synchronizing with iTunes, restoring and updating iOS.
Limits voltage and current when charging the device.

Yes, original lightning cable too expensive, for example, in Russian App Store They are asking 1,590 rubles for it. And this is for 1 meter of wire and two connectors, one of which is the simplest (USB).

Manufacturers of accessories spoke out in defense of user interests and offered analogues. However, “cable is different” and in pursuit of the lowest possible cost, some manufacturers (mostly Chinese) “forget” to add the necessary microchips to the Lightning connectors so that they at least comply with the MFi license. What kind of license is this?

MFi(short for " Made for iPhone/iPod/iPad" - Made for iPod/iPhone/iPad) is an Apple licensing program for manufacturers of accessories compatible with the iPhone, iPod touch and iPad.

Made for iPod/iPhone/iPad means that this cable or accessory has been specifically designed to connect to your iPod, iPhone, or iPad and has been certified by the developer to meet Apple performance standards. .

For certified cables and Apple accessories vouches for which and receives appropriate monetary deductions from each unit, which means they are safe for your device (theoretically).

In addition to the price, original Apple USB cables have serious problems with durability: they quickly fray and break.

I myself stopped using the original Lightning cable from the iPhone 5s in favor of the black Juicies+ with lightning connector and I don’t regret it at all.

So, in order for your iPhone, iPod Touch and iPad to charge at the permissible voltage and current, and also synchronize without errors, use at least certified cable Lightning. It is cheaper than the original one. But, if you do not have such an opportunity, there is a way how Apple protection and charge, sync and using the cheapest cables.

"The cable is not certified." What to do?

In some cases it is enough:

Sometimes you need this:

For jailbroken devices in Cydia, find and install the “Support Unsupported Accessories 8” or “Unauthorized Lightning Cable Enabler” tweak.

Remember that the problem cannot be completely eliminated in this way - this is only a temporary solution. Apple can always block the “singed” cable at the iOS level. In addition, you risk running into an expensive replacement of the power controller - the cost of the service starts at $80.

Therefore, we strongly recommend using either an original accessory or a certified one, for example, anyone can afford one iPhone owner 5 and later models).

There are times when the warning “This cable or accessory is not certified and is not guaranteed to work reliably with this iPhone” appears even when connecting the original cable, for example, if...

2. USB cable is damaged

If you are definitely using the original cable, and the ill-fated message still appears on the screen, your cable may simply be damaged.

If there are no visible signs of damage, to check, take a known intact (and, of course, original) cable and check the operation of your device with it. If it works, replace the cable with a new one.

3. The connector on the iPhone/iPod Touch/iPad is clogged

We have already written about this situation in. The bottom line is that the connector on the iPhone or iPad (this is especially true for Lightning connectors) various debris gets in and accumulates there for a long time. At some point, there is so much debris that it breaks the cable contact in the connector - and, accordingly, a corresponding warning appears. The solution is to carefully clean the debris from the connector. To do this, you can use a toothpick or a cotton swab moistened with alcohol. I advise you to clean the Lightning connector with your iPhone turned off.

Conclusion

And finally. Since 2008, I have always used the original cables to charge and sync my iPhone and iPad - it's safe and reliable. But if one of them was damaged and failed, I didn’t buy the other original one - it was expensive. Instead, I used a certified one, which I advise you to do. If you don’t have one at hand, you can charge the device once or twice with the cheapest cable, but don’t abuse it - the “unexpected” can sneak up unnoticed.

A broken charging cable is the bane of every phone. The most important thing is to find a replacement in time. However, it is not always possible to fork out for an original iPhone. Fortunately, non-branded analogues are common. But to use them, you still need to try.

The problem is that Apple is too self-centered. Therefore, if users should buy something, it should only be with their logo. And thanks to this policy, iPhone in its program code has some interesting lines. They forbid him to use a cable that is not produced by the parent company. And the cost of a real accessory from Apple is quite high. But the proprietary cord contains a special chip, which the device must analyze in order to work.

How to charge an iPhone with a non-original wire

But despite all Apple’s tricks, you can still use a non-native USB cable. Although you will have to suffer a little each time for this. So, a list of actions that need to be carried out so that your iPhone still “eats” the non-original plug and starts charging:

Connect the charger with the cable inserted into it into the outlet.
Take the wire plug and insert it into the smartphone. The latter must be blocked.
A warning will appear that you need to close. To do this, you need to pull it to the side.
Only after this - unlock the device.
Reject everything the iPhone complains about again.
Without blocking the device, remove the cable plug from the Lightning socket and immediately return it to its place.
And again, reject all the windows with which the miracle of Apple technology will notify you.

After this simple list of actions, the device should begin to receive energy.

Is it safe to charge with a non-original cable?

Such manipulations using a cheap cable, which for some reason is still not equipped with a normal chip (for example, like wires from Remax), can be very expensive for its users. Relatively new iPhones 5 among all their hardware have a small but very unpleasant module. It is almost invisible to the eye, but it can really ruin your life.

This little rascal is called U2 IC. It analyzes which cable is currently being used with the smartphone. And if for some reason he doesn’t like this cord, it simply breaks. And if this chip breaks, you will have to either get rid of the iPhone or repair it.

What problem does it cause? It's simple. Without an adequately functioning U2 IC, the device is unable to receive power. Even if it regularly enters the gadget, it does not reach the battery. As a rule, owners think that the battery is damaged, and then they go to change it. But this doesn't help - as soon as new battery will discharge to zero, more smartphone will show no signs of life.

So what should we do?

Use only high-quality non-original iPhone cables! All manufacturers that respect themselves and their name have long been aware of which chip inside the plug is responsible for initialization in the device. And they even learned to fake it. And therefore, you should not take Chinese “noname” wires from the nearest kiosk. They are certainly cheap and available. But won't it be more expensive to repair your mobile phone later?

It’s better to spend a little money and buy an accessory that is a little more expensive than a Chinese one, but still cheaper than the original one. There is a lot to do in this area. Many manufacturers offer their services:

company . There is no need to even doubt this - this company, according to assurances, is certified by Apple themselves. Consequently, your gadget will not suffer from the use of wires purchased with this brand;
firm . Their products attract attention; it is impossible to pass by such a wonderful purchase. Their big bonus is that they don't stop at boring monochromatic cables. The Remax assortment includes dozens of different wiring. In the catalog you will find everything, even fabric-braided data cables, which remain operational longer than regular ones;
manufacturer named . Severe and solid models for mobile phones, which will not become a problem for the user. They are produced with a leather braid, which is more reliable than even fabric. There is no need to talk about quality - it definitely exists. Not a single gadget, according to user reviews, failed while Just was working with it.

“This cable or accessory is not certified...” is a message that you may not have encountered personally, but you have definitely heard about it. We all know how short-lived original lighting from Apple is and how expensive they are. Buying a cable not from the manufacturer is fraught with risks unpleasant consequences. They usually find out about them when it is too late. What to do if you find yourself in a similar situation? How to charge your pet? And why might such an alert occur if everything was fine up to this point?

Why do users buy replicas?

The purpose of buying a copy cable is clear - the desire to save money. Analogue made in China cheaper than Apple products. At the same time, a scary message with the text “This cable or accessory is not certified” sometimes does not appear immediately. Someone may have a question: how exactly does the phone recognize that the connected cord is not “native”?

The bottom line is that a special component is installed in this original lighting - a microcontroller. One of its functions is to ensure that the charging and data transfer process can occur no matter which side you insert the cable into. This microcontroller is most likely missing in Chinese replicas. Alternatively, it is damaged or simply does not meet the phone's requirements. Because of this, problems subsequently arise.

What problems might arise from using such a cable?

As you can see, Apple strictly monitors the use of products not made by itself. Special devices do not allow charging; a message appears on the screen stating that this cable or accessory is not certified, so the reliability of its operation is not guaranteed.

Of course, one of the main reasons for this phenomenon is the monopoly on production. But the representatives themselves name another, no less significant one: a fake cable is almost guaranteed to cause serious harm to your iPhone. Firstly, if you use a Chinese replica, the Apple phone may simply stop charging and connecting to the computer. As a rule, at the very inopportune moment. Secondly, the original lighting is designed specifically for iPhone. Using a fake may damage the Apple phone due to technical inconsistencies. Then your losses will be much more serious than the cost of buying a new cable.

A simple method that can make a non-original cable work

Let's say a phone, on the screen of which a message appears that this cable or accessory is not certified, does not charge. What should you do if you can’t find a replacement cable right now, but you definitely need to charge your phone? No one gives a 100% guarantee, but sometimes this method helps:

First, try inserting the cable the other way.
If all else fails and the same message appears on the screen, close it.
Unlock your phone and the alert will pop up again. Close it again.
Unplug the wire and then immediately plug it back in.
In some cases, after this, charging begins to occur as usual.

How to charge a device with a copy by turning off the phone?

Another simple option on how you can try to make a non-original cable work:

Connect the wire to the device. A warning will appear on the screen. But you shouldn't pay attention and take out the cable.
Turn off your phone. At the same time, make sure that lighting remains connected.
If this method is suitable for your phone, the charging process will begin. A disconnected device cannot check the cable and “notice” that it is a copy.

This cable or accessory is not certified: how to bypass it via jailbreak?

This cable or accessory is not certified... Solve this problem You can also use jailbreak. The algorithm of actions is as follows:

Jailbreak your phone.
Launch Cydia and go to the Sources tab.
Here you should find the item Support Unsupported Accessories 8. It is this modification that is responsible for activating support for non-original devices.
This tweak is absolutely free. Feel free to click “Install”.
After rebooting the device changes made must take effect.

Now when connected charger the process should proceed without problems. The message may still appear. However, this will not affect the result.

What to do if a problem with a lace appears out of nowhere?

A gadget that displays the notification “This cable or accessory is not certified” is not charging? What to do if yesterday you attached the same cord, and everything was fine? And are you sure of the noble origin of your cable? There may be several reasons:

Over time, any equipment deteriorates. The charger connector may have become oxidized or dirty. Swipe visual inspection. Dirt can be removed with any stick, but use sharp iron objects! This will only make the problem worse.
Assess the condition of the wire itself. A message that a given cable or accessory is not certified may appear even from the original model if it is damaged. The most weak spots- points of articulation. Minor damage can be repaired. But if the shell is seriously damaged, there is only one way - to the store.

Now, if the message “This cable or accessory is not certified” appears on the screen, you already know what to do. But it’s still better not to skimp. Therefore, advises you to buy original lighting. Otherwise, the consequences may be more serious than just a dead phone. Then the iPhone will have to be carried in service center, which will entail even greater expenses than purchasing the original cable. It’s better to allocate a certain amount and buy the necessary lace than to pay twice later. By the way, the new cable can be further strengthened. Then it will last much longer.