Stream to media player classic. Setting up a computer to watch video using the hardware capabilities of the video card
No matter how good the video playback may seem, it can always be improved. There are quite a few ways to optimize a video, but one of the most important is adjusting the smoothness. The reasons why playback may not seem smooth enough can vary, but as a rule, this is due to shortcomings in the performance of the computer and its graphics subsystem, incorrect order of interlaced video fields, and a mismatch between the frame rate and the screen refresh rate.
Most video files that can now be downloaded on the Internet have a frequency 24 FPS. This standard was adopted back in 1932 year as a compromise between playback quality and film consumption. 24 frames per second video playback could be made smoother by lowering the screen refresh rate to 24 Hz. But this can only be done for TV screens; if you open the settings of a computer or laptop monitor, most likely only two parameters will be available: 50 Hz And 60 Hz. Displays with support 24p These are rare, but if your monitor is one of them, consider yourself lucky.
But what should everyone else do? Go the opposite way. If the monitor's refresh rate cannot be reduced to the video frame rate, then increasing the video frame rate to the existing screen refresh rate is very possible. How?
By interpolation of adjacent frames. Its essence is to add intermediate frames to the video sequence, generated based on two "real" neighboring frames. For this we suggest using special program or for short SVP. The principle of its operation is clearly demonstrated by a drawing taken from the official website of the project.
The main advantage of this program is that it does not require additional settings, and therefore can be used even by beginners. SVP includes two main modules: SVPflow And SVP Manager. The first module is responsible for calculating and adding frames to the video stream, the second provides access to program parameter settings. You can download the full (non-Core) version of the package from the official website www.svp-team.com/wiki/Download/ru. For correct operation SVP you will also need a video player that supports external filters DirectShow. Best suited for these purposes 32-bit(!) Media Player Classic Home Cinema (MPC-HC) . Default MPC-HC is already included in the SVP installation package, so the smartest thing to do would be to install it standard version with the parameters that the wizard offers and do not have to worry about filter settings later. Render component MadVR SVP is not required for operation, but it can be checked.
If MPC-HC is already installed
If you already have Media Player Classic Home Cinema, the checkbox in the SVP installer wizard window can be unchecked, but the player itself will have to be slightly configured, in particular, add components to it ffdShow And . To do this, go to the player settings,
In the left column we find "External filters", click "Add".
And in the window that opens, select "ffdshow raw video filter".
Return to the settings window and check the box for the added filter "Prefer". For adding open any video file in MPC-HC, go to the system tray, find the icon there ffdshow And double click open the settings on it.
We look for the item in the left column and mark it with a tick.
If MPC-HC was installed together with SVP, you don't need to configure anything. SVP is smart enough and that's it necessary settings produces itself, taking into account the configuration of a specific computer, and to convert video 24 FPS to 60 FPS, you just need to start playing any video file in MPC-HC. In this case, in the lower left part of the player window you should see a line "SVP: Playback 23.976 * (18:7) = 61.653 fps Auto trim: " .
Your aspect ratio and FPS may be different, but it doesn't matter. If such a line appears, consider that everything was done correctly and smooth playback is guaranteed.
As for the settings of the SVP itself, you won't need them. However, it’s still worth familiarizing yourself with them, but you don’t need to change anything, unless you know exactly what your actions will lead to.
Perhaps our readers already have a question: is there some kind of catch hidden behind all this? It's all too simple. No, there is no catch here, but the SVP interpolation algorithm is not without certain drawbacks.
Firstly, This increased load on CPU throughout the video. This is explained by the fact that the program calculates additional frames and integrates them into the video sequence on the fly. Secondly, when watching a video containing scenes with fast-moving objects, Minor artifacts may sometimes appear in the form of foggy halos, whose blurred contours resemble a moving object. And yet, against the backdrop of all the advantages that using SVP provides, these disadvantages seem very insignificant.
Setting up a classic player. Greetings, dear reader! In this article you will learn how to customize the classic player and replace the standard buttons on the panel.
It won't be full customization, but only changing several important parameters for comfortable use.
I abandoned the Windows player a long time ago, even disabled it in the system. How to disable Windows components look video tutorial. And all because he didn’t want to read some video formats.
I used it for a long time, without changing anything, until I noticed that this player has amazing capabilities. And look what...
Setting up the classic player
IN top panel In the player window, go to the “View” tab and at the very bottom of the drop-down menu, select Settings. That's where you make all your changes. I suggest watching a video tutorial on setting up a classic player.
It will give you the opportunity to quickly understand the settings. In addition, I put an interesting feature into it, this is a replacement for the standard navigation buttons with the help of which it will be more pleasant for you to use it.
What is the advantage of Media Player Classic?
- Media Player Classic reads everything popular formats and this is his most important advantage.
- The player starts up very quickly and does not load the system.
- There is an opportunity in it. Although “” also has such a function.
- It's convenient to pause. No need to aim at the buttons. You just have to left-click on the video.
- The sound is adjusted using the mouse roller. Which also eliminates the slowdown in action.
- The player has an accelerated video or audio playback mode. Useful feature if you need to watch the video in accelerated mode.
- It is possible to save watched videos as bookmarks. And if you didn’t have time to finish watching the video but added it to your bookmarks, then the next time you start it from bookmarks, it will start from the place where you saved it in bookmarks.
- IN Media settings Player Classic can be set so that the player plays all files that are in the same folder. That is, after finishing playing one file, the next file starts automatically. It’s so convenient to listen to music while going about your business and without being distracted by switching to another song.
- During playback, the audio player can be compressed to compact size so as not to block the workspace.
And this is not all the usefulness, as it would seem to us, of a simple classic player. The one thing it lacks is an equalizer, or maybe I just didn’t find it.
This is useful to know:
Hello everyone, friends! Today I will help you set up 5.1 surround sound, like in home theater(and maybe not only at home...).
Not pseudo-quadra and not expanding the sound base by mixing an adjacent channel into the phasing.
Namely, so that each soundtrack the file had its own column in the room.
This article will help us set up 5.1 sound.
By default, the player, or rather the codec, has such a setting that the sound on the receiver from the computer is only in the front channels: left and right.
It's time to expand your horizons!
By 5.1 we mean the following system:
C- center channel (it is more often used for voice)
S.W.— subwoofer channel (so that it hits the floor, and more powerfully, for the joy of the neighbors)
FL— far front left
FR- far front right
SL— far rear left (located behind the listener on the left)
S.R.— far rear right (located behind the listener on the right)
You need to get an amplifier (receiver) that will support the connection of 6 speakers, and that each has a separate input and a separate output.
Also, the sound card on the computer must support such a connection. 
If there are fewer outputs, you will have to purchase an additional sound card 
The green connector is usually the main one by default. The speakers are connected to it: left and right front.
Orange combines the center speaker and subwoofer.
Black are the rear speakers, which are in the back.
Gray is for 7.1 (plus 2 more columns for our still life).
To begin with, let's set the sound card to 5.1 (no, well, you can do 7.1 if the equipment allows it).
I show the example of sound Realtek cards. Although, the interface is not much different in older versions. However, the new one is more convenient and beautiful. 
To the right of the drop-down list there is a Play button. It allows you to check how each column works individually.
We will set it up using the example of the Classic player, which is included in K-lite Codec Pack.
And no need to say that:
- This is a codec dump (especially for people who edit videos), I will say this: if your hands are straight, then the programs will work to your advantage.
- It is impossible to get 5.1 in the Classic player, since only 2 speakers work. Everything is possible, 5.1 and even more: squeeze out all 17 channels at the same time, if your equipment allows it. Only in the case of 17 speakers, you will be hung with them and wires.
Let's launch the video file in the Classic player. Let's go to the settings and make sure that the sound is sent to the desired sound card (for me it is number 15 "Realtek Speakers"): 
Is there sound? In all columns? No? We go to the tray, there are icons of the codecs with which the player works: 
You need to open LAV. 
Let's uncheck the "Mixer" box. It is usually set by default for 2-channel sound cards, however, we have already gone further, breaking stereotypes and restrictions!
Applying the changes. If the sound does not appear in all speakers, then select 5.1 from the drop-down list and apply it again.
That's it, the sound MUST be in all the necessary speakers.
If this is not the case, check the equipment, restart the player, or see if the video file has ended? =))
Tags for search engines, do not read them:
how to enable 5.1 sound in media player classic, 5.1V sound setting media player classic, audio 5.1 no media player classic, 5.1 output media player classic, set up 5.1 on windows 7, set up 5.1, set up 5.1 on windows 8, set up 5.1 on a computer, set up 5.1 sound, how to set up 5.1 on realtek, how to set up 5.1 on windows xp, 5.1 acoustics setting, setting up a 5.1 audio system, setting up 5.1 in windows 7, setting up 5.1 in winamp, MPC,
Required software:
- DirectX 9.0c End-User Runtime June 2010– offline installation (recommended) or online installer. Installation is required for proper operation video player MPC-HC and is necessary in any Windows versions, up to Windows 10, despite the fact that this version already has DirectX 12.0. If DirectX 9.0c is already installed on your computer (for example, with some games, and on Steam it is installed automatically), then you do not need to download it again.
- Platform Update for Windows 7 SP1- download . For Windows users 7 this package must be installed to use DirectX 11 features in the madVR video renderer (discussed below).
- Microsoft .NET Framework 4. For users Windows Vista and a newer one most likely will not be needed. Mandatory for Windows XP.
- Media player MPC-HC
- Video renderer madVR
Step 1 — Installing MPC-HC and madVR
Download and install the MPC-HC media player.
Step 3 - Setting up LAV Splitter Source and LAV Audio Decoder
To access the LAV Splitter Source settings, launch any video file using MPC-HC and pause. After that, click in the video area right click mouse and select “Filters->LAV Splitter Source (internal)”.
Set the values as shown in the figure. Click the "Apply" button to save the settings, and then the "OK" button.
To access the LAV Audio Decoder settings, launch any video file using MPC-HC and pause. After that, right-click in the video area and select “Filters->LAV Audio Decoder (internal)”.
In the “Bitstreaming” section (the setting is necessary only in case of output digital audio S/PDIF, HDMI; in other cases, there is no need to mark anything here) when selecting DTS-HD, you do not need to check the “Use DTS-HD Framing for all DTS types” option if your receiver does not need it.
Then go to the “Mixing” tab and check the “Enable Mixing” option. Select required configuration audio in the “Output Speaker Configuration” item. For example, if you have a regular pair of speakers, then select the “Stereo” configuration. Click the "Apply" button to save the settings, and then the "OK" button.
This is a convenient player in all respects. It is based on the classic media player Player Classic and has a built-in set of media codecs, thanks to which it can play many formats of audio and video files without installing third-party codecs.
To install Media Player Classic (MPC) you need to follow the following instructions.
Step 1. To begin the player installation process, double-click installation file. In the installation language selection window, select Russian and press OK.
Step 2. Before proceeding with the installation of Media Player Classic, it is recommended that you close other applications to avoid installation errors. To continue installation click Further.
Step 3. Read carefully License agreement. Having agreed with him, set the switch to the mode I accept the terms of the agreement. And then click Further.
Step 4. In the window Selecting the installation folder leave the default path or change it by clicking the button Review. For Media installation Player Classic you will need 11.9 MB free space on your hard drive. Continue installation by clicking Further.
Step 5. Select the components you want to install. To do this, check or uncheck the boxes next to this component. Click Further.
Step 6. In a new window, you can select a folder from the Start menu. If you do not want to create a folder with the Start menu, then check the box Don't create a folder in the Start menu. Click to continue Further.
Step 7. In the next window Select additional tasks . In the block Additional icons check or uncheck the box Create an icon on the desktop and choose who to install them for Only for current user or For all users of this computer . Then click Further.
Step 8. Everything is ready for installation. In the center of the window you will be presented with all the information about the installation. To install MPC click the button Install.
Step 9. The installation process will begin, during which the installation wizard will copy and install all necessary components. Installation lasts 5-10 seconds.
