DVD drive does not work on Asus laptop. The disk drive does not work - what to do?

The vast majority of modern laptops are equipped by default with a universal disk drive that allows you to work with disks various types. However, it also happens that the laptop cannot read the discs or the drive refuses to work at all. In this article we will talk about possible solutions to these problems.

There are several reasons why the disk drive on a laptop may not work properly. In most cases, it all comes down to device failure or lens contamination.

Reason 1: Physical problems

The first step is to check whether the disk drive on the laptop is working properly and whether it is visible as equipment in "Device Manager". Follow the steps we described in other articles on the site and, if this does not bring results, proceed to the next section.

Just like on a computer, you can special problems replace a faulty drive by first finding and purchasing a suitable replacement. Moreover, if desired, you can install an additional hard drive instead of an optical drive.

Reason 2: Laser contamination

If the drive is correctly connected and configured, but does not read discs well or at all, the problem may be that the laser head is dirty. To correct the problem, open the drive and gently wipe the focusing lens.

Note: Cleaning must be done with the laptop turned off or after first disconnecting the drive from the laptop.

To remove dust, it is best to use cotton swabs pre-moistened with isopropyl alcohol. After cleaning, be sure to remove any remaining alcohol from the focusing lens.

Do not use improvised solutions to replace alcohol, as this may damage the device more than before. Also, try not to touch the lens with your hands without using a Q-tip.

After completing the cleaning process, you need to turn on the laptop and check the functionality of the disk drive. If the discs are still not readable, the laser head may be damaged. In this case, the only solution is to replace the faulty drive.

Reason 3: Storage media

The third reason the drive on a laptop does not work is due to the lack of support for a specific type of storage media by the device. This doesn’t happen often, since the laptop’s optical drive is designed for any type of disc.

In addition to the lack of support, the problem may be that the storage medium itself is faulty and therefore cannot be read. Due to the relatively low level drive reliability similar phenomenon- Not unusual.

You can check for a malfunction using other disks or a device with the ability to read optical media.

Reason 4: Incorrect entry

When trying to read information from rewritable media, errors may also occur, which, however, have little to do with optical drive malfunctions. The only option here is incorrect entry files.

This problem can be corrected by formatting and rewriting information, for example, using the program. In this case, previously recorded files will be completely deleted from the media without the possibility of recovery.

Note: Sometimes such software interferes proper operation drive.

This problem is quite common, there can be many reasons, including: hardware And software.

The saddest option is complete breaking devices. If your drive has been in use for a long time and at some point stopped reading discs, then perhaps its service life is already running out, this situation is especially typical for laptop drives. Unfortunately, their resource is short.

DVD drive has failed

In any case, do not rush to get upset, test the drive on another computer, if it works there, there are software problems.

Make sure the drive is physically correct connected. Do you remember if it was turned off? Suddenly you forgot to connect it.

The hardware problem also applies laser clogging(dust on the lens). If the drive is displayed in the Computer section, but the discs are not readable, then perhaps the laser could simply be clogged.

You should open the device and use a simple cotton swab to carefully clean the head. Also for these tasks there are special discs on which cleaning agents are applied. Spinning such a disc in the drive will clean the laser head.

If the laser head completely broken, and not just clogged - you can, of course, try to take it to a service center, but it’s easier to completely replace the drive than to try to resuscitate it. Don't want to bother with installing a new drive? Can buy portable. It costs a little more, but it is much more convenient. You can connect it via USB port when you need it.

Software causes of malfunction

The situation is simpler with software problems. The disk drive may be disabled in BIOS. Detailed Guide on inclusion specifically for your BIOS version can be found on the Internet.

Remember at what point the drive stopped reading discs. You may have installed a program like Alcohol 120% or Daemon Tools. Emulators virtual disks I can be cause broken DVD-Rom. In this case, you can try the following. Go to Device Manager. This can be done via Control, right click by Computer icon.

Go to device Manager and make sure everything is in order there, in the section DVD drives and CD drives. In chapter IDE ATA/ATAPI controllers delete duplicate channels, if any. After that restart computer.

If this doesn't help, remove the software causing the failure and check the drive again.

In the manager you should also pay attention to the section DVD drives for the presence of non-working or . In this case you will need reinstall driver.

There is another option remove device And restart PC, this way you can start reinitialization.

Has your disk drive suddenly stopped working? The reasons may be completely different and in this article we will look at the most popular, and also look at ways to solve them.

1. Complete failure

If your drive is many years old, and yesterday it suddenly stopped reading discs, then perhaps its service life has come to an end. In this case, you can test the drive on another computer and if it doesn’t start there, then the drive is probably broken. But we have 4 more options, why might the disk drive not work?, so read them before you make a conclusion.

2. Disabled in BIOS

If you recently wandered through the BIOS settings and changed something, then maybe you accidentally disabled it? Make sure this is not the case. Find instructions on the Internet on how to enable the drive in the BIOS and after logging in, see if it is disabled.

3. Windows is slow

It happens that something is screwed up in Windows and the system simply does not see your DVD drive. Need to try go to Device Manager and see if everything is in order there and if there is an unknown sign opposite some devices.

4. Laser is clogged

If in the section Computer The drive is displayed, but does not read discs, then it is possible the laser in the disk drive, which reads information from disks, could simply be clogged. You need to open the device and clean the head with a regular cotton swab. There are also special discs with a cleaning agent applied for these purposes. By inserting a disk into the drive, it will spin and clean disk drive laser head.

5. The laser head is broken

All equipment breaks down sooner or later, and the disk drive laser is no exception. In this case you need replace the drive. It costs about 10 dollars. If you don't want to bother with replacing the old one (opening system unit removing the drive and installing a new one), then you can buy an external one. It really costs more, but it connects much easier, usually like a mouse or keyboard, it is inserted into any free USB connector. Suitable for both laptops and computers.

Of course, these are not all the reasons why doesn't the disk drive work?! You may have another reason. And I told those that I myself know.

Can be different reasons, Why laptop doesn't see disk drive. Below we list everything possible options, which you can handle yourself and which are best fixed in a service center.

To begin with, you can clean the drive lens, for which you will have to either completely disassemble it or use special cleaning products, for example, cleaning discs or kits. But the network is another option; you can purchase a new drive. Our gsmmoscow service has a large assortment and specialists will definitely select the right model. If The disk drive on the laptop does not work, and you want to replace it yourself, we will give you some recommendations on how to do it better. If you follow the installation technology, have an idea of ​​what you are doing and knowledge, then everything should work. But on one condition, that the reason is really in the drive, otherwise you wasted your time and money. To avoid such unpleasant consequences and disappointment, come to the service center and find out about the problem from the specialists after diagnosis, so as not to pay twice later.

Reasons why the disk drive on a laptop does not work.

If Doesn't open or read disk drive on laptop, there are several serious reasons for this.

1. In many situations, the problem lies only in the operating system. Try to reinstall the OS, which you can do yourself or seek help from specialists. There is a price list on the website that indicates the cost of such a service.

2. Malfunctions can also be in the drive itself; our housing and communal services center has a large assortment, and workers will quickly replace it with a new one. Price the desired model and you will see the service itself in the price list.

3. Problems also occur with the south bridge, and it is useless to repair it; it’s easier to replace it. For all information on prices, please see the price list.

To find out what damage is hidden in your laptop PC, you need to diagnose it. Our service offers this service free of charge.

Laptop doesn't see disk drive? Want to know how long the repair will take?

The approximate amount of time it will take to repair the parts is as follows.

1. To replace the drive, it takes at least 1 hour;

2. It will take at least 2 hours to reinstall the OS and configure drivers;

3. When replacing south bridge you need at least 4 hours.

Our service center provides customer service very quickly and efficiently. And it helps us with this big choice spare parts, tools and experience of our specialists. We service the following brands of laptops: HP, Asus, Samsung, Toshiba, Acer, Sony Vaio, Lenovo, Dell.

Pay attention to the operating rules that will help you use the drive for a long time. Do not use solvents such as alcohol, antistatic sprays, or household cleaners to clean your PC and drives. It is better to clean the disc with a soft cloth, working from the center to the edge. If the contamination is severe, you can moisten the material with water, squeeze it out and then wipe the surface. And in order not to complicate your life, throw it away, of course, if information that is important to you is not stored there. When writing data to disk, try not to disconnect or connect the power source and the laptop itself, and it is also advisable to avoid shocks and shocks.

For the modern user, a disk drive is an integral device in both a computer and a laptop. Disks, or blanks, continue to be common storage media and will not lose their relevance any time soon. We record our favorite music on them, and install films from them. And when the drive for some reason stops reading discs, this is very sad. Firstly, the user is deprived of one of the storage media, and secondly, reinstalling the system becomes doubly difficult. But even when a DVD Rom completely refuses to work, this does not mean that it is time for the trash heap! There are several reasons why it may refuse to read blanks, but in almost all cases it can be restored to functionality. Let's figure out why the drive doesn't work and how to get it to read discs again, as before.

The disk drive in the computer refuses to work: common reasons

Often in situations where a DVD-Rom stopped working, the reasons turned out to be trivial. Let's look at the most basic of them first.

1. Physical shutdown. In most cases, the device is simply not connected to the . Moreover, the user could accidentally pull out the plug from the connector while cleaning the computer from dust. This reason is not surprising for Sata interface, because such connectors quickly become loose. It happens that the plug itself can fall out of the connector. All you have to do is move the computer.
2. Problems with the cable or connector. It's also quite common problem. If the device does not work, and everything is connected correctly, there is no need to rush to write it off as scrap metal. Try switching the cable to another socket. If that doesn't help, replace the wire itself.
3. No matter how funny it may be, some users classify the device as non-working as soon as it fails to read one disk. One should not rush to such conclusions. Check the disk itself for damage. If the blank is scratched, which often happens, then that is the problem. Feed the device another disk and check how it is read. If everything is in order, it means that you sinned in vain on the drive.
4. The laser is clogged. Also a very common problem. But it is relevant for drives that either work very long time, or are used extremely often. To revive the drive for service, you do not need to carry it and pump it out specialized software won't be needed either. Everything can be managed by going to the nearest store, which sells discs with music, games and films. You need a cleaning disk. This is a common item, so you can buy it anywhere. Suppose you bought such a blank. It comes complete with instructions and a special liquid for cleaning laser lenses. What do we do next? We carefully read the instructions, we understand that the cleaning liquid is a very dangerous thing and if it comes into contact with fire, it can lead to dire consequences. So, after reading the instructions, apply liquid to the disk brushes and carefully insert it into the drive. After the device eats the blank, a program for cleaning the laser will be loaded. She herself will tell us what to do. And yes, we read the instructions. We carry out necessary actions, wait for the cleaning to complete. We remove the disk and rejoice at the live drive again!

Disk drive failure due to emulator installation

If all of the above did not help you, then remember which program you installed last.

If you installed programs for emulation virtual drives Alcohol 120%, Ultra ISO and others, the cause of the drive failure may be related to them.

Such programs often cause conflict between virtual device and physical. How to solve this problem? Here are a few options that will help you successfully solve the problem.

(banner_123_privod)

1. The best way to fix this problem is to roll back the system. During installation, each program creates a restore point to which you can return. The main thing is that the system restore function is active. So, to rollback, follow these steps:

• Open "control Panel". Next point "recovery". After this you need to click "running system restore" and select a rollback point. In our case, it is necessary to restore the computer to the state before installing the emulator. Accordingly, we select the point created by this program. Click next. After the recovery process, the computer will restart and the system will report that it has returned to its original state. early state. Next we turn to the drive and voila! He works! The screenshot below shows an example of how this will look.

1. If for one reason or another the recovery of the operating system was disabled or the rollback point before installing the emulator was deleted, do not lose heart! You can fix the problem manually. To do this we do the following:

• First, we remove the emulator itself. So much so that not even a breath remains of him! We clean absolutely everything: both the Program Files folder and the application data folder.
• Let's go to device Manager, we find the virtual drive. We send it to the same address where we sent its creator.
• Then, without leaving the device manager, open the menu, view and select the item show hidden devices. Next we see an impressive list of incomprehensible devices and drivers. Don’t be alarmed, we only need one item from them - SPTD Driver. We find one and also delete it.
• After all this, remove the drive itself, reboot the system and enjoy a working device again.

If none of the methods helped, then there is only one conclusion left, and not the most comforting one: the drive is still dead. In this case, you can try to repair it, but the cost of this service is comparable to a new device.

What to do if the disk drive in your laptop does not work

When a drive installed in a beech machine refuses to work, the reasons remain the same as in the case of a computer. Let us repeat them again and briefly describe possible solutions to the problems.

1. There is no cable in the beech, but the connector is still there. Only, unfortunately, he is alone. To check if the drive is OK, connect it to another laptop or computer. This is quite possible.
2. Again, damaged disks. Don't be so quick to blame the drive. Check if it may not read one or 2 disks that are damaged.
3. Lens clogged. A cleaning disc can also help here.
4. Installing a virtual drive emulator. As before, the solution to the problem is either to roll back the operating system or to correctly remove the culprit of the problem and all its components.
5. Device failure. Here, as was written above, nothing will help. You'll have to buy a new device.

(banner_123_privod)

DVD-Rom does not work after purchase

Not all the products we buy in stores are of high quality. No matter how hard manufacturers try, out of 10 devices one turns out to be defective. This is not the law of meanness, but a human or equipment error. What to do in such a case?

• Don't panic. This is not a situation where you need to show your emotions. Try connecting the device to different sockets on the computer. Check the cable, replace it.
• If all else fails and the drive does not work, do not try to figure out the problem yourself.

If you open the device, the warranty will be void.

• Contact the store or service where you purchased the DVD-Rom. According to the consumer protection law, you have the right to demand from the seller poor quality goods the entire cost, or replacement with a working device. But they won’t give you a new drive right away. The returned device will be tested by the seller before your eyes. If the problem is confirmed, you will be apologized and the store will offer a replacement product or refund your money. When I encountered a similar situation, the drive was tested long and hard for three computers. But he didn’t make money on any of them. As a result, I paid a little extra and bought a normal working drive.
• If the seller refuses to replace the DVD-Rom, citing one reason or another, there is no need to create scandals and run into trouble. Take your non-working device and go to court with confidence. If the equipment is truly faulty, the examination will determine this. The main thing is not to open the drive. Next, you can sue the store for the cost of the goods and even demand compensation for moral damages. Consumer protection law will be on your side. If a fault really exists, you will win the case anyway.

Is it always possible to return the drive to functionality?

When the drive fails, and not just the cable coming off or any of the above reasons, you can try to repair it. In some cases, this will cost you less than buying a new device. But, unfortunately, repair is not always possible. In what cases is it worth repairing the device, and in what cases is it better to think about buying a new one?

1. When the laser fails. If it is still possible to change the laser lens, then the laser will be very expensive. In addition, each disk drive manufacturer uses different lasers, which may not exist in our country. It will, of course, be ordered, but how long you will have to wait is unknown.
2. When the electric drive fails. This happens extremely rarely, but it does happen. This part is also not at all cheap and again, it is not known how long you will have to wait until it is delivered.
3. Damage to the board, as well as damage to chips or capacitors. This drive part is also quite rare, because each manufacturer uses its own design. Accordingly, you will have to order the board directly from the factory. It's time again. Resoldering capacitors or chips is a painstaking task and not every service will undertake it. And this service will not cost much less than a new device.

(banner_123_privod)

Finally, a few tips that will extend the life of your drive and save you from unnecessary worries.

• Do not insert damaged or scratched discs into the drive. This significantly reduces the service life of the device;
• Do not leave DVD-Rom open. This allows dust to accumulate and clog the laser lenses. In the future, it goes without saying, this will not lead to anything good;
• Don't force the drive long work. He gets tired too. Allow the device to rest at least every half hour if you have to frequently work with disks;
• If the drive is actively used, do not neglect periodic cleaning of the laser lenses. But you don’t need to do this too often, since there is a risk of scratching the lenses;
• If possible, avoid using emulators virtual drives. In cases where they are very necessary, be sure to check whether system recovery is enabled and whether a rollback point has been created.
• If you are a laptop owner, all the recommendations are the same. But I’ll also draw your attentionthat you should not touch the drive itself, much less the laser, with your fingers.

Everything goes wrong at times. Drive is no exception. However, this breakdown can cause serious problems for its owner.

What to do with a broken disk drive

Naturally, look for a solution to the problem, and not wait for everything to work itself out!

First of all, you need to test the drive. You need to connect it to another computer and check. If the drive performs its functions perfectly, then the problem lies in your computer (it happens). If the drive does not work on another computer, then it is necessary to “treat” the drive itself.

By the way, if the new disk drive does not work, amateur activities are not allowed. Entrust the repair to specialists from the service center and observe. Exceptions may be cases when the computer itself is to blame, and not the disk drive.

Sometimes the disk drive (or rather, the laser head) can be brought back to life using a special cleaning disk that can be purchased in stores. It is possible that a speck has simply gotten onto the optical element and is interfering with normal operation.

Why does the disk drive break?

1. The main causes of failure are most often mechanical damage. These problems can occur due to dust accumulation in the optical drive or improper handling. In this case, it is recommended to return the drive to a service center or purchase a new one.

2. Drive may fail computer viruses(by disrupting the drivers). You can solve the problem with viruses by installing an antivirus or reinstalling the operating system. In any case, the computer needs to be cleaned of harmful viruses. It is easy to identify a virus if the disk drive autorun does not work.

High-quality computer protection can only be achieved using the latest versions of an antivirus equipped with the latest databases data.

Which will monitor security, can be accessed from the official website Avast.com.

3. Quite often the physical disk drive of the computer does not work, because... cannot read low-quality discs. Before inserting a disc into the drive, you need to wipe the CD or DVD from dust and make sure that the coating is intact. But even in this case, you may not notice microcracks or errors that prevent normal reading. Insert another disc and analyze the results.

Who is guilty? - Disk drive!

Before taking a broken drive for repair, you need to make sure that it is really faulty. There is no point in paying to repair a working optical drive, but cleaning the drive is a completely different price for the service. That's why it's better to check everything carefully first:

Try different discs
- connect to another computer.

Direct text: Before placing the disc in the drive, it is recommended to wipe it from possible dust and dirt, removing it. In addition, “crumbling” disks (with crumbled or damaged coating), when examined in detail (if you look through such a disk at a beam or light source), will have obvious gaps (holes) in the surface coating. It is better not to place such discs in the drive at all! In the same category we place discs with pronounced deep scratches. And if your drive doesn't work, it's possible that you're trying to run just such a physically damaged disk.

First you need to find out what the problem is: in the disk or in the CD/DVD device drive.
This is quite easy to do, try reading several other discs on your problematic CD/DVD drive. If one of the disks is readable, then continue reading below, And if not, then you should go to this page

First of all download Nero program CD-DVD Speed ​​to test your CD-DVD drive.

The most common cause of drive failure is mechanical damage. This damage may be due to dust in the optical drive or due to improper handling. And then you must take your drive to a service center, or simply buy a new one. Another reason why a disk drive fails is a virus. If you think that your computer has become infected with viruses, then once all the viruses are removed, you need to install an antivirus on your computer and constantly download the virus database update to it.

And it also happens that the drive itself is working properly, but the whole problem is in the inserted disk. A disk malfunction occurs due to the fact that microcracks have formed on the disk, interfering with the operation of the disk drive. Here, you just need to insert another disk into the drive and you will see whether it is good or not.

Practical solution to the problem:

Causes and symptoms of the malfunction:

If the drive on a laptop does not work - regardless of what type of drive it is (dvd, cd, blu-ray) - then we can talk about three reasons for the malfunction. The first is glitches in the operating system ( Update driver!!!). Second - incorrect work south bridge. The third reason is a malfunction of the drive itself.

What you can try:

Step 1: Click Start => Run. Dial in the dialog box"sysdm.cpl". Press Enter => "System Properties".

Step 2: Go to the "Hardware" tab and click the "Device Manager" button, the tab is named "DVD/ CD-ROM drives." Double click on it to show its contents. The mine was a question mark, but in some cases it may have exclamation mark next to the name. Mine was named "AOPEN DUW1608/ARR", but if yours is different, that's ok.

Step 3: Double click on the newly opened Hardward "AOPEN DUW1608/ARR" and its own dialog box will appear. Go to the "Driver" tab and select "Update driver..." from the buttons below.

Step 4: Now select “Install from a specified location” and click Next. In the next window, select "Don't search. I'll choose the driver I need" and click Next again. Various window will be displayed with compatible hardware for the driver. I chose the one below thinking it was the latest one, it was called "CD-ROM Drive." Click Next and Finish on the instructions it gives you.

After that The DVD/CD-ROM should work fine, I was able to run it.

Hope this helps you guys!

After that, If you move from a lesser “evil” to a greater one, then try reinstalling the operating system. If this does not help, then replace the drive. If the problem persists again, then the laptop must be shown technical specialists.
Phones service centers in other cities, see the contact page.

If you are afraid to fix the drive yourself, then contact your nearest service center.

Many people have had problems with their computer at least once. One of these problems is the failure of the disk drive. And then you immediately have questions: “Why doesn’t the disk drive work?” Of course, then you immediately think about what needs to be done and so on.

There is no need to be mistaken and think that everything is lost and now you need to buy a new drive. We need to try to restore it. By at least, find the reason.

Option one.

Turn on the computer and see if the “light” on the disk drive is on. If it burns, then everything is not so bad.

That is, in fact, it works, but the operating system does not see it. This means that the drive is not transmitting information to the motherboard.

In turn, the reason for this may be poor contact, or its complete absence. You need to try disconnecting and then re-enabling it. It also happens that motherboard Quite a lot of dust accumulates, and if it gets on the connectors, then this could also be the reason that your drive is not working.

If this does not help, then buy another data cable or plug it into a different connector.

Option two.

The “light” on the drive works, the computer detects it, but the carriage does not extend.

What to do in this case? But this is not such a serious problem, since it works itself and the computer sees it. If the cage of your drive does not extend, then it immediately becomes obvious that your belt (the rubber band that extends the carriage) has stretched and failed.

In this case, it needs to be replaced. Some people don't change and just use something spicy. For example, a needle or pin. And with their help they open the disk drive.

Option three.

Everything seems to be working. It starts, the computer detects it, and, most importantly, the carriage comes out. But at the same time, the computer becomes very slow, especially when you start inserting disks.

This situation happens when there is a device conflict. They can create problems and all kinds of interference for each other. This problem is usually solved by simply rearranging the data cables. For example, plug the cable from the drive into another connector, and from the hard drive into another.

The computer can slow down not only because of the disk drive. Perhaps there is another reason. You don't need to think about it right away.

OptionR.I.P.

If your drive shows no signs of life, then most likely it is burned out. Take it apart. If it stinks and has a burning smell, then it is burnt. More precisely, the microcircuit burned out.

Nowadays, it is cheaper and easier to buy a new drive than to look for a board and repair it. It's not cost effective.

Good day, dear readers of my blog! Today, a disk drive is not the most necessary device in a laptop. Of course, there are situations where it is necessary, but in fact there is no real benefit from it. But what to do if you suddenly need it, the answer is simple - repair or change, but first you need to understand why the disk drive on the laptop does not work. Over a long time of working with laptops and PCs, I have encountered various malfunctions and in general I will divide them into 5 cases.

The most obvious option is that the drive simply stopped working. This happens with technology and there is no point in finding out the real reason. You just need to check whether the drive is really broken or whether it is a laptop malfunction. The test is carried out by connecting to another device. If there is a breakdown, then we buy a new one and replace it. Replacement is a simple matter - remove back cover and unscrew the two bolts. We installed a new one, screwed it on, updated the drivers. Everything is working. To simplify the task, we buy external drive, it is connected if necessary via a USB connector. By the way, buying a disk drive does not depend on the laptop brand - the connection method is standard for both Samsung and HP. All drives are interchangeable and the Acer device works with Toshiba.

Situation 2

Sometimes the problem is not with the drive itself, but with it being disabled in the BIOS. This may be due to a glitch or it may be done this way by default. Many modern manufacturers do not put a disk drive in a laptop, but leave room for it. Similar system found in Asus and Lenovo, and other well-known companies. IN in this case It’s not enough to just connect the drive, you need to activate it in the BIOS. This is done in a standard way– enter the BIOS (Del, F*) and find a menu with devices, then opposite the drive name select the Enabled value, which can be interpreted as “enabled”. The principle of operation is the same for Windows 10 and earlier versions.

Situation 3

A malfunction can sometimes be caused by software - viruses or a device driver. In this case, we clean the laptop using an antivirus and update the drivers. It is important to remember here that the driver is downloaded for a specific OS and its bit depth, for example, for Windows 8 64-bit version. The Windows 10 driver will not work on it.

Situation 4

The drive does not read all discs. In this case, the disk or drive is to blame. If the media is too worn, the laser head will not be able to read information from it. In this case, the disk must be replaced. If the device basically does not read disks, but you can hear that it is trying to do so, then it may be caused by a simple clogged head. You can clean it with a special cleaning disk (you could once buy it everywhere), but now you can’t find them, so we just open the drive and clean the surface of the laser with cotton wool. Special means, such as cologne or alcohol, there is no need to use! They harm the mechanism.

Situation 5

The read head is damaged. This happens rarely and it is difficult to name a specific cause of the breakdown. Repair is not advisable here, since its cost is 80% of the price of the drive. It's easier to install a new device. The price of a new drive varies from 1300 to 1800 rubles, which is very little.

Conclusion

A disk drive is a device in which the main working element is a laser head. Damage to it will affect the operation of the entire system. To avoid damage, you should use whole disks and generally keep your laptop clean. Dust that gets into the holes of a laptop affects not only its cooling, but also the operation of individual components. My advice is to stop using the floppy drive, as it is safer to store all the information on a flash drive or external hard drive. Even Windows 8 and any other version can be installed from a USB drive.

Subscribe to updates and see you again!

Thank you for your attention! Sincerely, Rostislav Kuzmin.