How to tune channels on TV Sony Bravia. Instructions.

Everyone in their life has had to tune channels to various models TVs. The process of searching for channels is approximately the same. This also applies to Sony Bravia TVs. On some models, you can tune channels without using the remote control.

1. Use the search function for all available television channels for Sony Bravia brand model, in automatic mode. At the front of the TV panel, hold down the “Menu” button for a few seconds to launch channel settings. You can also use the remote control for these purposes. remote control. “Menu” and “ Automatic search channels." Wait until the setup of the found channels is completed. After completing the procedure, your TV will go into normal mode to view.

2. You can configure channels in manual mode. You can start this mode using special buttons on your remote control or on the panel of your Sony TV. The channel frequency is adjusted using the +- buttons. After this, adjust the signal quality using the “ Fine tuning" Do these steps for each TV channel.

3. To move from one item to another in the TV menu, use the buttons to adjust the volume. On some Sony TV models, the found channel in the automatic search mode must be recorded for later saving by pressing certain buttons on the remote control.

4. Find the instructions for your Sony Bravia TV and read it. Pay attention to the section dedicated to setting up channels. If you are not provided these instructions together with the TV system kit, you can download it on the official website Sony, or using other Internet resources. If you were unable to tune channels on your TV, then call the service technical support. There they will explain to you in detail the entire setup process, from start to finish. The service telephone number is indicated in the documentation.

5. If you are using satellite equipment, but not regular antenna, then configure the channels directly on the receiver itself.

More interesting background information about mobile phones, cameras, MP3 players and other digital equipment

The instructions on how to set up a Sony TV are universal and suitable for almost all models. The menu interface is similar, so there are no significant differences.

Experts note that the menu of Sony brand plasmas is more complicated than that of TVs of other brands. It is sometimes difficult for the user to understand unclear symbols additional functions, applications with which the panel is equipped.

Before connecting the device to the network, you need to check that all cords are connected correctly and that they are securely fastened. After turning on the TV, you need to wait a while so that the installation of the system is completely completed, only after that you can proceed to the basic settings of the Sony TV.

All actions are performed using the control panel. Parameters such as sound, image, Internet connection and speaker system must be configured in the “HOME” menu. This is the main tab, that's it necessary settings Sony TVs are performed in it.

Automatic channel search

Setting up a Sony TV begins with searching for TV channels. On new models it is performed automatically. To start the operation, you need to hold the “MENU” button for a few seconds; the TV screen will display standard settings to search for TV channels.

During the procedure, interference and channels found by the device will be displayed on the TV screen. When the search operation is completed and the channels are in the correct order, the screen will function normally.

Search for digital TV channels

Settings digital channels happens according to the following scheme:

1. Go to the “Main Menu” tab by clicking Home button on PU.
2. Select the “Digital Configuration” section; if there is no such section, then select “Autostart” and immediately go to step No. 5.
3. Tab " Digital tuning" - "Automatic search for digital stations."
4. Select cable type connection.
5. You must enter the parameters required for the search.
6. If all actions are performed correctly, the device will find digital programs available for viewing.
7. To turn on the internal clock: the following actions: “installation” - “digital configuration” - “technical configuration”.

1. In the tab that appears, select the GMT time zone .

This is the main way to set up digital channels on a Sony TV.

In order to install channels on Trinitron models, you must adhere to the following rules:

1. Press two keys on the remote control at the same time (up arrow and right arrow).
2. Using the PROG button, select the channel number that should be infused.
3. Press the button (up arrow) and the keys next to it.
4. In order for sound to appear, hold down the key (up arrow), as well as the key with an asterisk.
5. Remember desired channel and press two keys on the remote control (up and right arrow).
6. The operation is completed.
7. If you cannot find the TV in this way, this means that the device has problems with the memory unit, repairs are required, it is recommended to contact a technical center.

The best option for setting up channels on a Sony Trinitron TV. Detailed information can be found in the instructions supplied with the device by the manufacturer. If there is no paper copy, it is recommended to find its virtual version on the company’s website. The user needs to thoroughly study the instructions for his model to avoid problems when connecting the equipment.

Also read, and.

How to set up a Sony TV? First, adjust the picture and sound settings. Then proceed to search and save TV channels. Users are offered two modes - automatic and manual.

Modern TV models from the famous Japanese brand support all standards digital signal. The search for TV channels is carried out through the built-in receiver. Additionally, you don’t have to buy a receiver and connect it to the TV.

Step-by-step instructions for setting up channels have been developed especially for users who have not previously used Sony TV equipment. We will also consider the features of adjusting image, sound and other important parameters.

Every user can set up the TV correctly. Just follow the recommendations from the professionals. Setting the sound (volume, volume) is easier. Go to the corresponding tab of the main menu and select the optimal parameters.

Adjusting the image will take more time. In order for a clear and rich picture to appear on the screen, you need to adjust a lot of parameters. Now let's look at the basic subtleties of setting up a Sony TV.

Preparatory work

Save the image calibration diagram below to a USB flash drive or external HDD. Connect the memory drive to the TV via a USB connector. Open the picture for customization through the media player.

On new models running on Android platform TV, files for calibration are played from a DVD or Blu-Ray player. Because it is impossible to change settings through the Album application.

First, we set up the main indicators. To do this, you need to disable advanced options. Open the main menu and go to “Settings”, and then to the “ tab System Settings" and the subsection "Eco", here turn off the light sensor.

Return to the main menu and go to “Settings” again, and then to the “Image” tab to deactivate the following functions: reality creation, smooth transition, noise reduction.

For highlighting, set the value to 7 or 8 points. For Picture Mode, select Standard. Once these changes are made, switch to the Advanced tab to deactivate all features.

Access the settings menu only through the HOME button. If you edit settings using the Options button, the settings will be applied to one signal source, and not to the TV as a whole.

Calibration

Start by checking that the image size settings are correct. The default settings enlarge the image. As a result, sharpness decreases. This manifests itself as moire, which can be seen in the outlines of the resolution bands.

To adjust the picture size, open “Settings” and go to the “Screen Control” tab to disable “Automatic Display Area”. Function " Maximum resolution"Turn it off too. Now arrows are visible in all corners. The moire effect has disappeared.

Brightness

Calculate the darkest part of the grayscale band in the pre-downloaded chart. Adjust the brightness so that the black area (located on the left) is as dark as possible. Are there any differences between the left and right sides of the screen? Brightness is set correctly.

Contrast

Find the lightest part of the diagram. Adjust the contrast until the right side of the screen is as light as possible. The difference between the left and right sides of the diagram should be noticeable.

Sharpness

Increased sharpness is the cause of an unnatural image. To avoid this, adjust the sharpness. There should be no light outline along intersecting lines on the calibration diagram. Reduce the sharpness until the contour disappears completely.

Saturation of the color palette

Colors will be saturated when all transitions are viewed on the calibration chart. Look at the center of the scale to achieve a natural rendition of shades.

Sound settings

Select audio playback mode - internal speakers or external acoustic system. Extra options are missing. Just adjust the volume.

Extra options

Connect the antenna cable to the appropriate connector. Select the signal source "Antenna". Disable additional devices. Now the TV is ready to search for TV channels.

How to connect a TV to a router? This option is only available to owners of TVs that support Smart TV. Synchronization is carried out via Wi-Fi router or by connecting the cable to the LAN connector.

Automatic channel search

There are two ways to set up TV channels, let's start with automatic search. Take the remote control and open the main menu. Select the "Automatic channel search" command. In a few minutes, the TV will independently find and save available TV channels.

The Sony TV screen will constantly change as you search. Interference will appear periodically. After completing the setup, the device will begin to operate in standard mode.

To adjust all channels on your Sony Bravia TV or find new ones, use the manual search function. It can also be turned on through the main menu.

Manual channel search

Channels on a Sony TV are also manually tuned. Take the remote control. Open the main menu. Go to the section " Manual search channels." Use the “+” and “-” buttons to change frequencies. Gradually increase the value.

After this setup, you need to fine-tune the quality of TV broadcasting. Use the "Fine tuning" option. Apply it to every channel. After completing image adjustments, save the result.

Setting up channels

1. When you turn on the TV for the first time, select the “Russian” language:

2. Select the country “Russia”:

3. Create and enter a pin code. For example "1111":

4. Select the “Home” operating mode:

5. Select your TV location. For example, “Table Stand”:

6. Select the broadcast type “Digital and analogue TV”:

7. Select the TV connection type “Cable”:

8. Select the “Other” operator:

9. Select FREQUENCY TUNING - MANUAL

Set the frequency to 298 MHz
Select the menu item "Start"

Sorting channels

How to enter sorting mode

Press the “Home” button on the remote control, go to the “Settings” menu, select “Settings” analog channels»:

In the menu that appears, select “Sorting programs”:

To go to the digital channel sorting menu, press the “Home” button on the remote control, go to the “Settings” menu, select “Digital Configuration”:

Select the item “Sorting digital programs”:

How to sort channels.

From the list on the left, select the channel that you want to move to another position (the position number is displayed in the “Prog.” column) and press the center button on the remote control pad:

After pressing the center button on the remote control, the selected channel will move to the right side of the screen. Fill in the "Enter program number" field with the desired position to which you want to move this channel, and press the center button on the remote control cross:

The channel has moved to the position we selected:

Sorting digital channels is done in a similar way.

You can see the list of analogue channels for your city. You can use it as a guide when sorting.

Don't forget to select your city in top menu site.

Preparing to set up your Sony Bravia TV:
Set up the dish and point it at the EUTELSAT W4 (36B) satellite. Details about Tricolor satellite coverage area and direction satellite dish in your locality indicated on the Tricolor website. Write down the local oscillator frequency parameters indicated on the satellite dish converter.

In our case, the upper frequency is 10.75 GHz

Make sure the TV is turned off. Connect the cable from the satellite dish to the TV's satellite dish input, marked with the icon:

Install the smart card with your subscription into the CAM module (DRE-Crypt CI+ module) provided by the satellite TV operator:

Install the CAM module (CI module) into the appropriate slot on your Sony Bravia TV, marked with the icon:

Note: You may need to remove it from the connector first. CAM module DRE-Crypt CI+ TV security plug

Setting up your Sony Bravia TV

1. Turn on the TV and go to Settings -> Digital configuration -> Auto satellite tuning

2. Confirm that Auto Satellite Tuning will begin.

3. Select your satellite dish configuration. With regular customized satellite antennas parameter should be selected

"Fixed antenna or DiSEqC" (default). Click Next

On the scan page selection page, leave the default settings and confirm - “Next”

4. Select the first satellite (Satellite 1) and press the center button on the remote control to enter the settings menu:

5. Select “LNB Configuration” and enter it:

6. In the “Lower LNB range” and “Upper LNB range” items, enter the corresponding values ​​of the converter local oscillator (see paragraph 2 of the “Preparation” section). In our case, “LNB Low Range” by default coincides with the corresponding local oscillator parameter. But “Upper range LNB” is not. Enter the appropriate values ​​for this parameter in megahertz (10.75 GHz = 10750 MHz) and confirm:

7. Go back to previous sony menu and pay attention to the “Transponder” item. At this point, you can directly configure the parameters for receiving software packages. The default transponder settings in the TV menu are the same as the Tricolor TV transponder settings in the Western region.

For this reason, no settings changes are required at this point. It may be required if the signal parameters are changed by the satellite TV operator or if TV is configured in other regions.
If the antenna is connected and the initial parameters are entered correctly, the screen will display an indication of the signal quality and strength.

Return to the list of satellites and click "Start".

8. Scanning of radio and TV channels begins, during which the progress and number of found TV channels (programs) are displayed.

9. The Sony Bravia TV setup is complete. Depending on the current set of programs transmitted by the satellite TV operator, the number of channels found may vary. Now you can either exit the setup menu or immediately sort the channels by pressing the corresponding button according to the prompt.

Attention! Some of the detected TV channels may not be available for display if they are paid and are not included in your subscription plan with the satellite TV operator.