Is it possible to connect wired Internet to the router? How to set up a router without the help of a specialist

All tips

How to connect the Internet through a router?

Using a router, or, as it is also called, a router, you can create a local network in your apartment that will distribute the Internet to all technical devices connected to it.

Today we will look at how to connect the Internet via a router yourself.

Equipment and device of the router

Router equipment

Open the box and check the contents. The router package should include the following: the device itself, an adapter (power supply), network cable Ethernet (RJ-45 connector), disk with drivers and installation program, router setup guide. Installation disk us in in this case will not be needed, since we will set all the settings ourselves.

Router device

Turn over your router rear panel to yourself and pay attention to the ports. Typically the device contains five connectors, four of which are the same color. These inputs are called LAN ports and are intended for connecting equipment with which you want to go online. global network. The fifth connector is different in color and is called WAN or Internet port. This connector is intended for connecting the Internet cable that was provided to you by the specialists of your Provider.

To the right of the Internet connector is the input for connecting the power supply. And the panel closes with a small button called “Reset”. The button is used to reset settings and reboot the router. To restart the device, you need to press the button (with a thin tip, such as a toothpick, etc.) and hold it for five seconds. When you press the "Reset" button, all installed settings and the default parameters are set.

Installation, connection and configuration of the router

Installation and connection

First you need to call the operator technical support your Provider. Tell the specialist that you want to register the router and tell the specialist the MAC address of the device (the number is on a sticker on the router itself and is also written in the instructions).
Determine the location of the device: the router can be installed directly in the room where the computer is located, or hung on the wall, for example, in the hallway. When installing the router, make sure that there is a 220-volt power outlet nearby.
Then connect the power supply to the router and plug the device into a power outlet.
Connect the Internet cable to the WAN connector.
Connect the network cable to one of the LAN ports on the router, and on the other side to the corresponding input on the computer or laptop.
After connecting the device, we proceed to setting it up.

Settings

Click "Start", go to "Control Panel", select the "Network Connections" tab and go to "Wireless Connections" local network".
Click right click mouse on the connection icon and select "Properties".
Then click on "Internet Protocol (TCP/IP)" and click on the "Properties" button.
Check the appropriate boxes to automatic settings IP and DNS addresses.
Depending on the operating system The progress of setting up IP and DNS may vary. (Click the Start button and select View network connections". Next, select your connection type and go to the "Local Area Connection" section. Go to "Properties" and select "Internet Protocol Version 4". Then, through the "Properties" button, go to the next window and check the appropriate boxes for automatic configuration of IP and DNS addresses).
Next, find the device’s IP address in the router’s instructions. For most manufacturers, the router has an IP address of 192.168.0.1 or 192.168.1.1.
Enter IP in address bar browser and press the "Enter" key.
In the window that appears, you must enter your username and password. The data also needs to be found in the manual for using the router. For most models, the username is admin, the password is admin, or an empty string (that is, the password field remains empty).
Then again you need to dial the Provider operator and find out the following settings characteristics: connection type, server, username and password. Also inquire about availability additional settings.
After entering the default username and password, you need to go to the “Setup” section and select the “Internet Setup” tab.
Then click on the “Manual Internet Connection Setup” button and write down all the settings that the specialist dictated to you.
After entering the settings, click the "Save" button.

Check out the articles as well.

In reality modern world Every Internet user should know how to connect a router. Routers are quite simple network hardware. Anyone can set them up, but only if they follow certain instructions. We will tell you everything from “A” to “Z” about connecting, activating and setting up a home modem.

Selecting a location

Once you have purchased new router and unpacked it, there is no need to rush to connect it. The router needs to choose the right location, because the quality of the signal and its distribution throughout the apartment depend on this. The choice of location is based on several parameters:

available network cable length;
availability of a nearby outlet;
dimensions of the house or apartment.

Most even budget models have powerful transmitters to ensure signal distribution in three-room apartments. It is recommended to place the device on a hill (on the highest shelf, on top of a table, or attach it to the wall) for better signal propagation. Make sure that the LAN cable and power cord are loose and not under tension.

Do not install the modem near electrical appliances (TVs, microwave ovens or on the system unit). Remember that metal barriers weaken Wi-Fi the most. If you have metal cabinets or cabinets, of course, we recommend moving them to the outer walls. If in a private house the coverage area does not cover all rooms, then it is worth strengthening the signal or purchasing a repeater.

Connecting the router to a laptop or PC

Having chosen a place, it is worth inspecting the purchase package to begin connecting. As a rule, the kit also includes a LAN cable, instructions and a disk with electronic documentation or support software. At a minimum, you need to connect the router to an Internet cable, and you can configure it either from a PC or laptop via Wi-Fi.

Via cable

If you are using an ADSL or Ethernet connection, then you need to connect a wire with the Internet to the router (as a rule, this is the classic “ twisted pair"). Take the end of the cable and then plug it into a port called WAN. It is usually highlighted in color separately from others. Next, connect the output of the network card to the LAN port of the router. There are usually 4 of them in the device. They are marked in yellow/orange.

Next, take the power supply and plug it into a power outlet, and insert the end of the wire into the connector on the modem (it can be designated as 5V-2.5A or Power). Use only factory power supplies, as products from third-party manufacturers may produce a different voltage, which in extreme cases will lead to burnout of the microcircuits.

Connecting the router is very simple, and then you can configure the device via the web interface directly from your computer.

Via Wi-Fi

A Wi-Fi router has one important advantage - it can be configured remotely without resorting to physical connection through the wire of the device and the computer. As a rule, most models immediately distribute Wi-fi after switching on. A password is not set, but if there is an icon with a lock on the network, then you should look at the factory code for the network on the label of the router.

Find the wireless networks icon in the tray and click on it;
select yours from the list wireless point access and click “Connect”.

We recommend sitting as close to the device as possible, since the data transfer speed directly depends on the distance. If Wi-Fi does not activate automatically, you will have to do it manually. Then you can connect to the router only in one way - wired.

Setting up the router

Some providers do not require the user to set up a modem, since after the steps described above the Internet is already available on the computer, however, these are rare situations. More often than not, you have to manually establish the connection. Wi-Fi setup is required if you want to put your password on the network.

Login to the web interface

First, you need to learn how to enter the main menu of the router. Please note that the device does not need to be connected to the Internet at all to do this. You will need any browser ( Google Chrome, Opera, Firefox or similar). Next you need to know:

IP address where you can access the modem menu;
username and access code (password).

This information is located on a special label attached to the case. The login is usually the English word admin, the password is either similar or presented as a combination of numbers (1234 or 0000). It depends on the manufacturer.

Once all the information received has been found, follow these simple steps:

You will be taken to the main menu when you provide the correct information. Now you can change the device settings. You can log in not only with personal computer, but even from a phone, repeating this procedure in a mobile browser.

Reset all settings

Before performing any actions, you need to figure out how to return everything to its place if incorrect parameters are set. Modems have a special feature called Factory Reset. It will override any changes made by the user. You can reset the device in several ways:

Separate RESET button. Hold it for more than 10 seconds before everything indicator lights will light up and go out.
Combined WPS/RESET button. It is also necessary to hold it for more than ten seconds.
Soft reset via the corresponding item in the system menu.

After the reset, the login information and Wi-Fi password (if there was one) will be reset to the factory settings. This the only way regain “control” over the device if it has been hacked by intruders.

Internet setup, connection types

Let's move on to the most interesting part - setting up an Internet connection. Typically, the procedure comes down to determining the type of connection and setting the specified parameters, which are provided by the provider. Let's look at connection types using the example of the common Wi-Fi router TP-LINK TL-WR840N. Menu options may vary slightly on other devices.

The connection is configured in the “Network” section, WAN subsection. The following types are available for you to choose from:

This router model has a “Detect” button. Once it has been pressed, the system will automatically select the connection type to be used.

Wi-Fi setup

If you are using a Wi-Fi modem, then the menu will have a special item for setting up the device as an access point. More advanced models can work as a client or repeater. To start setting up, you need:

At the end, all you have to do is click the “Save” button. Some models will also require a reboot for the changes to take effect. Do not use simple passwords similar to combinations of numbers from 1 to 8 or the famous “qwerty”. They are easy to select not only specialized software, but also ordinary users. These are all the steps needed to activate Wi-fi.

Other settings

Depending on the manufacturer, of course, routers have a number of additional settings. We recommend reading in detail about each of them in the technical manual. The most common and useful ones will be presented here:

MAC address filtering. The function allows you to restrict access to Wi-Fi for individual devices. For example, you can prevent your neighbor’s phone from connecting, but you will first have to find out the MAC address of his device.
Creating an additional guest network. The device creates a separate network with its own password. You can limit the number of users, connection speed, and more. Useful when using the modem in public places.
Virtual servers. Allows you to redirect incoming packets to the required address.
Parental control. Restricts access to specific resources (completely or partially) certain time). Useful feature if there are children in the family.
Backup copy. With its help, you can create a file with settings, and if there are problems with the device, restore them in just a couple of clicks.

Do not set parameters on the router that you have no idea about. They may disrupt or block Internet access.

Changing the password to log into the web interface

As you noticed, standard passwords The web interface is identical on almost all models. To prevent attackers from playing around with your router, we recommend changing your password. This is done through one of the sections of the standard menu:

This simple step will significantly improve the security of your network. The knowledge gained will be useful many times in life. You shouldn’t pay an adjuster for basic steps that you can do yourself in 5-10 minutes. If difficulties arise, do not be lazy to open the instructions.

Report content

Routers have long ceased to be something rare and unusual. Nowadays there is a router in almost every office, as well as in most homes that have the Internet. This article was written for those who recently purchased this device and are just figuring out how to connect the router to a computer.

Usually, desktop computer connect to the router using a cable. While laptops and netbooks are connected when WiFi assistance. In this article we will look at the connection process using a cable. So, for this we need the following equipment:

The router itself. You can read about that in one of our articles;
Network cable. To connect your router to your computer via cable, you need a Cat 5e network cable. Moreover, this is given on both sides (the compression method is direct). As a rule, the router comes with a ready-made crimped network cable about 1.5 meters long. This cable is perfect if you plan to place the router on a table next to your computer. If there is no network cable or it is too short, then you will have to purchase it separately.
Computer with network card. This shouldn't be a problem since most modern computers(as well as laptops and netbooks) are equipped with a built-in network card.

Once you have collected everything you need, you can begin connecting the router to your computer. To do this, take a network cable and plug one end into the LAN connector on the router, and the other end into network card computer.

Please note that the router may have a large number of network connectors. As a rule, these are 4 LAN connectors (connectors for connecting computers from your local network) and 1 INTERNET connector (connector for connecting to the Internet). You need to plug the cable into one of the LAN connectors (it doesn’t matter which one).

As for the network connector on the computer, there is nothing complicated here. As a rule, there is only one and is located on the rear panel system unit, next to the USB connectors.

If you are using a laptop or, then you need to look for the network connector on the sides of your device.

After you have connected the network connector on the router and the computer using a network cable, the indicator on the router should turn on, indicating that a device is connected to the router.

That's it, connecting the router to the computer via a network cable is complete. After this, the local network and the Internet should work on the computer.

A special icon on the taskbar will indicate that the network and Internet are working.

If something went wrong, this icon may be crossed out with a red cross. This means the network is down.

There are a large number of problems that lead to such a situation. The most common problems are:

Problems with the network cable. The cable is not connected, damaged or incorrectly crimped;
The network card is disabled in Windows settings;
No network cards installed;
The router does not work (is disconnected from the power supply or is faulty);

It is also possible that the local network is working, but there is no access to the Internet. In this case, a yellow triangle will be shown next to the icon.

There are also many reasons that lead to this situation. The most common reasons are the following:

The router does not have access to the Internet. Not connected to the internet, incorrect or incorrect.
Are used manual settings IP addresses.

Despite the wide range of fairly powerful devices capable of providing stable WiFi, the question of how to connect a second router to the Internet via a router is still relevant.

After all, installing a router-to-router bridge is often much more profitable and effective than purchasing a more expensive modern router. Such bridges will be of particular benefit in a private home or small office, where it is possible to “cover” the required square meters with the Internet at the lowest financial cost (and radiation power).

And in this article we will look at whether it is possible to connect a router to a router and how to properly connect two routers to the same network.

How to connect wifi router via router?

There are two ways to connect two routers into one network - using LAN cable or by wireless WiFi communications.

For a clearer understanding of this task, let’s briefly consider the meaning of a bridge in connecting router to router and distributing the role of routers. For example, let's call one of them “A” and the other “B”.

We will assign to router “A” “ main role" - a direct connection to the Internet, and router "B" will act as a "repeater" or "repeater" and broadcast the signal from the emitter "A" to other devices on the network.

How to connect a router to a router via cable?

First, let’s look at the connection of “LAN-WAN” routers (using the Tp-Link model as an example). This option has a more stable connection than LAN-LAN.

Router A settings.

To connect a tp-link router to tp-link router you need to make sure that in its settings .

The first router does not require any other settings.

Let's move on to router "B".

In the settings you need to set the dynamic acquisition of IP addresses:

- “WAN” tab - “Connection type” - “Dynamic IP address”;

- if the parameters “Ip address”, “Subnet mask” and “Default gateway” are indicated below, then the bridge is working, and router “B” is a client of router “A”.

How to connect a router to a router via wifi?

Let's set it up first wireless connection on router “A”:

- in the browser enter 192.168.0.1 (the address may be different, see), “login” and “password” by default “admin”;
- on the “” tab Wireless mode»Create a network name (SSID) and a password (it should be easy to remember for you, but at the same time reliable);

- another parameter – “Channel”. It is not necessary to indicate it, but it is recommended to do so, because matching network channels on devices will ensure more stable work networks.

Now let's move on to router "B".

Nowadays most network devices support WDS technology– this is a kind of repeater.

- Go to the device’s web interface;
- On the “Wireless Mode” tab, fill in the fields similar to the settings of router “A”;
- Below, check the “Enable WDS” item - it will appear additional window with parameters;

- There you will see the SSID (router “A”) and BSSID (router “B”). Click “Search” and in the “List of Access Points” window that appears, select the connection configured on router “A”;
- Save the configuration and reboot. This completes the setup of connecting the router to the router via wifi.

Cable connection of two routers to one network using the LAN-LAN type.

As already mentioned, a LAN-LAN connection is less stable than a LAN-WAN connection. However, for the “integrity of the picture”, we will still look at how to connect a tp-link router to a tp-link router with such a connection.

No settings are required for router “A”; all changes are made only on router “B”:

- Go to the device settings;
- “Network” - “Local network”. To avoid conflict, a few units more;
- On the DHCP tab, select Disable.

Settings are complete.

How to connect a d-link router via a d-link router?

Now how to connect the same two routers “A” and “B” to the same network, but of the D-Link brand:

1. How to configure the router as a repeater?

IN WiFi settings just specify the network name identical to router “A” and save the configuration.

2. Setup wireless bridge on router "B":

- “Wifi” tab - “Enable” - “Broadcast wireless network”;
- In the list below, select “main network” and set the same password as on router “A”;
- Next, on the “WAN” tab, create a new connection (to do this, click the “Add” button);
- “Connection type” - “Dynamic ip”;
- “Interface” - “WiFiClient” - “Apply”;
- Save the settings and reboot the device.

As practice has shown, the most stable connection is supported by bridges with Tp-Link models. With identical network parameters, D-Link devices provide lower communication quality: connection breaks often occur, speed drops, etc.

On the topic of connecting to the Internet via wireless network Many articles have already been written. Instructions for connecting, solving various problems, errors, etc. And in this article we will look at connecting a router to a computer using a network cable, which usually comes with the router. With a cable connection, everything is much simpler than with Wi-Fi. But despite this, sometimes problems arise with connecting to the router using a network cable (LAN).

Basically, of course, they connect to the Internet using a cable. desktop computers, which do not have a built-in Wi-Fi receiver. And if you buy it for a computer, then you can do without wires. I always advise connecting the router via cable to configure it, and of course update the firmware. There are different cases, maybe Wi-Fi does not work on a laptop, but you need to connect to the Internet, or the speed of the wireless network is low, here we need a network cable. A cable connection is always more stable than an air connection.

All we need is the network cable itself, which we will use to connect the computer to the router. This is a regular twisted pair cable, with RJ-45 connectors on both sides. This cable should be included with your router. True, it's short there (depending on the router manufacturer). If you need a long cable, a computer store can make one for you. You can do it yourself, but you need a special tool. There are plenty of instructions on the Internet.

As a rule, you can connect 4 devices to the router via a network cable. You will most likely find 4 LAN connectors on your router. In some cases, the LAN connector can be 1 or 8. It doesn’t matter which Windows version installed on your computer. The instructions are suitable for Windows 7, Windows 8, and Windows 10. In Windows XP, everything is connected in exactly the same way, but the IP settings will be slightly different.

Connecting to a router using a network cable (LAN)

Everything is very simple. We take a network cable, connect one end to the router into one of the LAN connectors (they are signed LAN, or home network) . And we connect the second end of the cable to the computer’s network card. It looks like this:

If you connect a laptop to the router, then we do everything exactly the same. One end of the cable to the router, and the other to the laptop’s network card:

That's all the connection is. If the router is turned on, the computer should immediately respond to connecting to the router. The connection status in the tray will change (bottom right corner).

If the Internet is connected to the router and it is already configured, then most likely the connection icon will look like this:

This means that everything is fine and the Internet is already working.

And if the router is not yet configured (you're just about to set it up), or there are some problems in the computer settings, then the connection status will be yellow exclamation mark. And without internet access. The Internet on the computer will not work.

If the Internet from this router works fine on other devices, but on the computer that we connected without access to the Internet, then we need to check the IP and DNS settings for connecting via the local network.

Without access to the Internet when connected via cable

It may be that after connecting the Internet will not work. The connection will be “without Internet access”, or “Limited” (in Windows 8 and Windows 10). If the problem is not with the router (he distributes the Internet), then you need to check the settings on the computer itself.

Right-click on the connection icon and select Network Control Center and shared access . In the new window select Change adapter settings.

And we set everything up as in the screenshot below. Need to set automatic receipt IP and DNS addresses.

After that, restart your computer, everything should work.

What to do if the computer does not respond to connecting the network cable?

It may be that after connecting the cable to the computer, the connection status will not change, and there will be a computer with a red cross (no connection).

In this case, try the following:

Connect the network cable on the router to another LAN connector.
If possible, replace the network cable. It is possible that the problem is in the cable.
Install or update the network card driver.
Go to adapter management and check if the Local Area Connection adapter is enabled. Right-click on it and select enable.
If the Internet via cable does not work on a computer with Windows 10, then see this article.

As practice shows, everything works via cable immediately after connection. Without any problems or settings. If you are unable to connect your computer to the router, then describe the problem in the comments. I will definitely answer and help with advice.