Hello, our dear visitors. Do you want to know how to configure the dir 300 router correctly? On this page, website I decided to tell you what it is setting up D-link DIR 300.

The model of this router is very popular in Russia and neighboring countries, so step by step setting up DIR-300 will definitely help many people set up home network. How to configure dir 300? We will assume that step-by-step correct setting D-link Dir 300 has begun! We are sure you can handle it on your own!

Setting up the DIR-300 router

In fact, in the setting router dir 300 nru there is nothing complicated. But most Dlink DIR300 owners are faced not with the problem of the setup itself, but with a lack of understanding of simple things:

• How to connect D-link DIR 300.
• What data to enter into the router.
• What connection does the provider use?
• How to connect WiFi after setup local network.

So, D-link DIR 300 is unpacked. Its kit usually includes instructions for setting up and connecting, but since you are on this page, it’s probably not that clear. Also included with this WiFi router Comes with power supply and patch cord. Let’s say right away that we will show the setup of D-Link dir 300 nru, but since there are several revisions of routers of the 300NRU model:

1. The DIR 300 NRU B7 we are reviewing.
2. DIR 300 NRU B6 - the previous revision of the router, differs in the admin panel interface.
3. DIR 300 NRU B5 is a very old model.

Don't be afraid that you have a different router interface. All settings for NRU are also relevant for other revisions. The main thing is to understand the principle.

By the way, we have already talked about the principle, and we also have an earlier one. Let's return to the D-Link Dir-300 and see what the router has on the back:

As can be seen from the figure, the router has four LAN RJ45 connector, which are needed to connect computers via a network cable, that is, PCs that are not equipped WiFi module. Also, the D-Link DIR 300 has WAN The connector is responsible for receiving an Internet channel from the provider. The round power connector is designed to connect the router using a power supply. This can already be done if you haven’t connected it yet.

After that, connect the patch cord (network cable that comes with the router). One end needs to be plugged into one of the four ports LAN, and the other into the network card of a computer and laptop. To the port WAN We insert the wire from the provider (do this later, the Internet will come in handy later).

As can be seen from the photograph, D-Link connection dir 300 is quite simple. Initial setup router dir 300 is finished. By the way, if for some reason you do not have a patch cord included, then you need to buy it or. Now it's time to go into the D-Link DIR 300 and configure it. Open the browser and enter the local address, as written in the instructions 192.168.0.1. Admin panels of all routers D-Link available at this address.

We enter the username and password that are set on the router by default. By the way, if for some reason you forget your password, we will change it below at the next D-Link setup dir 300, then restore your login and password by resetting settings dir 300. This can be done with the “Reset” button, which is located on the back of the router. Just keep in mind that all settings on the router will also be reset. Let's return to setting up the DIR300. A warning window will appear indicating that it would be a good idea to change the password, we will do this later.

Finally we got to the router admin panel D-LINK DIR 300!

Updating the firmware before setting up the router

Any modern router has firmware. Router manufacturers are trying to correct errors in the operation of routers, so it is worth updating the firmware of our Dlink DIR-300. To do this, let's check the firmware version at home page administration panels.

Now we need to pick it up new version firmware on the Dlink website. Follow the link ftp://dlink.ru/pub/Router/, find our router model and download the firmware with the file extension FWZ.

The firmware is updated in the admin panel. The update takes a little time. Let's continue.

Preparing to configure on Windows

One of important points In setting up the dir 300 router, and not only this model, is setting up a local network and connecting to the Internet. Moreover, connecting to a local network is easy, but difficulties may arise with the provider’s settings. In Russia, there are at least two large providers:

• Beeline.
• Rostelecom.

And there are countless less visible ones, most of whom are simply intermediaries, renting a channel from a large provider. And their connection settings may differ. There are several types of connection to the provider:

• PPPoE connection.
• PPTP connection.
• L2TP connection.
• IPoE connection.
• Connection via static IP address.
• Automatically obtain an IP address.

We are sure that many of you were wary - there are so many incomprehensible abbreviations. In fact, those who do not know what type of provider they are connected to need to do a few simple things.

We need to look at the settings in Windows XP let's go:

Start -> Control Panel -> Network connections-> Local Area Connection -> Properties -> Internet Protocol (TCP/IP) -> Properties

IN Windows 7 The settings of the network interface, which is responsible for connecting to the provider, are located:

Start -> Control Panel -> Network and Sharing Center shared access-> Change adapter parameters -> find the interface and go to Properties again twice, as in the picture

We remember what data is indicated there, you can even take a screenshot. After recording the IP, mask, gateway and DNS , you can put dots on “receive automatically”.

Setting up WAN and LAN interfaces on D-Link Dir-300

Let's move on to setting up a local network and Internet access on our DIR-300. Go to the tab:

Network -> Connections

And we'll choose WAN interface. A window will appear, the parameters of which will need to be configured.

This is where knowledge about the type of connection to the provider comes in handy. As you can see, the screenshot shows the settings for IPoE. Your settings may, of course, vary. For example, to change the settings to PPPoE, you need to at least change the connection type:

Let's briefly go over all the characteristics of this page:

• MTU - the value is responsible for maximum size a data packet that is transmitted over a channel via the TCP/IP protocol. Some providers only work with a certain MTU value, but usually it is 1500 and you don’t need to touch it.
• MAC: Unique network interface identifier. Some providers link to MAC address to protect your Internet connection. You can check this with your provider. If a binding exists, you need to find out the MAC address of your network card and enter it in this field.
• Obtaining an IP address automatically also depends on your provider settings. If in network interface Windows, which we talked about above, certain IP, mask and gateway values ​​were entered, then you need to uncheck the box and specify these parameters (remember, we asked you to write them down?)
• Obtaining the DNS server address is the same as with the previous point.

Save the changed WAN interface settings.

About LAN can be said simply. If you want network participants to receive an IP address automatically, then on the DIR-300 you need to leave everything by default, and in Windows check the “receive automatically” checkbox, as we described above. Otherwise, you can make a network by disabling DHCP V LAN, that is, so that the router does not give out the IP automatically. In this case, in the properties of the TCP/IP protocol you will have to specify the IP address, mask and gateway. For example like this:

• IP 192.168.0.2
• Mask 255.255.255.0
• Gateway 192.168.0.1

So, Dir-300 will be able to see your computer. What awaits us next WiFi setup on D-Link DIR-300, which we will issue as a separate article. We hope this article will help you connect a computer or laptop to the Dlink DIR-300 router. Now let's move on to the second part of our story about this router model and.

• Lera

  Hello, yesterday I installed the D-link dir 620 router, in the evening everything was fine, all 3 laptops used Wi-Fi. But before going to bed, I turned off the router by clicking off and in the morning, when I turned it on, of course, not a single laptop could connect. The router is not listed in the network adapters, although yesterday it was... I didn’t update because I got confused, there are a lot of different files and it’s not clear what to do, what to download and how to set the fwz format. I can no longer access 192.168.0.1. Please help me out.

• Lera

  I turned it off, of course)) first thing. But it didn't help, unfortunately. I think the point is that I didn’t update it, my version is 1.0.0, I already managed to press reset.

• LDemid

• Gleb

• Meow

• RedBull

  My question is this? I connected an internet cable to the router, from the router to the computer. And so first I went to the Internet without changing anything in the IP, and then I wrote what was above 192.168.0.1, etc., and that’s it, I can’t go to the Internet at all, what should I do? And I also connect to Wi-Fi from my phone, it says there’s supposedly an excellent connection and that’s it, but I can’t access the Internet, although Wi-Fi is turned on as the phone says. What should I do?

• birthday boy

  So, I set up the dLina 300 router a long time ago, everything worked. I decided to check how many users were connected. I pressed the reset, trying to get into the settings. Using standard login/password. Piget is not the correct login or password. What is wrong in my actions?

• Prince

  Good afternoon I forgot the password for the router, decided to reset it to factory settings and set it up again, clicked reset and now the laptop does not connect to the Internet and does not /see/ the router at all, even through a cable.

• andy15

  About once a day (from 10 to 11 pm, just when I first set up the router) the connection is lost. You have to turn the router off and on. How to get rid of this?

• Tanya

  Hello. I have dir 300, my laptop still connects, my Nokia phone connects via Wi-Fi, but my Samsung Galaxy won’t connect. Tell me something!!

• semen1234567

  hello =) I can’t figure it out, I found through the “cmd” command the ip mask of the gateway and dns servers, actually the problem is that there are 2 connections: “local network connection” - where ipv4 and the subnet mask are written, but the gateway and dns servers are not indicated and there are 2 it says “ppp adapter high-speed connection” - there is ipv4 (but it differs from 1) gateway mask and 2 dns network IP addresses, what data should I use? Thank you

• Lisa

  Hello, the router provided Wi-Fi for a year, and then the computer stopped seeing it (other devices saw it). When I tried to connect, my Wi-Fi appeared in the list, but the computer could not connect to it. As a result, I rebooted the router (dir300), and the computer sees a network called dir300, which is distributed by my router. When connecting to the router via cable, I go to 192.168.0.1, in the settings I rename the access point, set a password, click save, it hangs for a while, supposedly saves, then in the left top corner“Inaction...” appears and that’s it, it doesn’t save anything, Wi-Fi is still available to everyone. Please help me figure it out!

• Ivan

• Wirral

• boekanur

• Alexander

  Tell me, the router is DIR 300, in the online rooms there are 6 gran turismos, out of 16 participants on the track I see only 6 or 7 people, although they take part in the races, and some people are immediately thrown out of the room, what could be the problem?

• Novel

  Good evening. Please give me some advice. I reset all the settings on the router, configured it according to your instructions. As a result, the connection status lights up green icons, but Internet pages do not open. Wifi also does not work. Thanks in advance!

• VIKING

  Hello!! bought Dir-300! connected everything to the computer as in the instructions, went to the browser in address bar I entered the address and it opened a page for me where in the left corner it says d-link dir-300 and the rest of the field is a gray screen! I tried resetting the settings to do the same thing, what should I do???? thanks in advance!

• Helen

  Good evening. Help me please. I brought a Wi-Fi router from Rostelecom. I would like to connect it to the Internet via a modem. I inserted the cables correctly, as in the picture, I go to the browser, but it doesn’t load. I don’t know what to do!(

• Griff

  Hello. I have the same problem, the router worked fine for several years, but yesterday all devices stopped seeing it and even connected it directly via cable, but to no avail. The power lamp and the Internet are constantly lit yellow, does not respond to reset and does not enter the settings via the PC. Tell me what to do?

In order to start at a construction site D-Link router DIR-300, open the box and boldly tear off the orange sticker from the router. You can forget about the sticker.

We connect the router to the computer using the wire (blue patch cord) supplied in the kit.

First, open the browser ( Internet Explorer, Firefox) and type 192.168.0.1 in the address bar.

Connection via wireless network to the router may not always be successful, since in addition to your router, others may be available, it is possible to connect and configure someone else's D-Link DIR-300 router.

Login: admin

Password:(we leave the field empty, although out of habit I want to enter admin)

On the "Installation" tab, select the "Internet Installation" tab, and then the "Manually set up an Internet connection" button.

Looking ahead, I will say that the address on the provider’s local network can be issued dynamically or be static, usually at the request of the user. For a static address, providers usually ask for additional subscription fee. There are two options D-Link DIR-300 router settings, depending on the type of receiving addresses in your case, I personally use a static address, it’s more convenient.

Setting up a D-Link DIR-300 router with dynamic IP address assignment.

Option D-Link DIR-300 router settings No. 1, if the address is obtained via DHCP, i.e. dynamically.

In the “Internet connection type” field, select “PPTP Dual Access” (namely dual access, I don’t know the fundamental difference, but this is how you need to do it).

1. Select a connection with dynamic address assignment by the provider "Dynamic IP address".

2. MAC address – if the provider’s network has a binding by MAC address, click MAC address cloning, and router D-Link DIR-300 will copy the MAC address from network adapter your computer, relevant in cases where the router was not purchased at the time of connection to the provider.

3. IP address/server name – IP/Server name of the provider.

4. Account PPTP – username for authorization in the provider’s network.

6. Re-entry PPTP password – repeat the password for authorization in the provider’s network.

7. Select the connection mode - connection setup mode. In the illustration, "Always-on" is selected for permanent connection. "Connect-on-Demand" - establishing a connection when necessary - that is, when traffic directed to the Internet appears, the router establishes a connection, and if there is no activity for more than the time specified in "Maximum Idle Time", it disconnects. If you select "Manual", the connection is established and terminated manually.

8. Save changes to

Setting up a D-Link DIR-300 router with static IP address assignment.

1. Select a connection with a static address value "Static IP address".

2. IP address - the address issued to you by your provider.

3. Subnet mask.

4. Provider gateway.

5. DNS – DNS Server provider.

6. MAC address - if the provider’s network has a binding by MAC address, click Cloning MAC address, and the router will copy the poppy from the network adapter of your computer, this is important in cases where the router was not purchased at the time of connection to the provider.

7. IP address/server name – IP/Server name of the provider.

8. PPTP account – username for authorization in the provider’s network.

10. Re-enter the PPTP password – we repeat the password for authorization in the provider’s network.

11. Select mode connection mode connection setup. In the figure, "Always-on" is selected for permanent connection. "Connect-on-Demand" - establishing a connection when necessary - that is, when traffic directed to the Internet appears, the router establishes a connection, and if there is no activity for more than the time specified in "Maximum Idle Time", it disconnects. If you select "Manual", the connection is established and terminated manually.

12. Save changes to settings of the D-Link DIR-300 router by clicking the "Save settings" button.

After correct settings, connection router D-Link DIR-300 Internet connection must be installed, as indicated by the "Internet Online" indicator on the left side of the browser screen.

If you want to get rid of annoying cables, not be tied to one place of work on a computer/laptop, and easily move everything computer equipment-needs to be purchased and configured wifi router. A series of articles about setting up various routers will help you easily set up a Wi-Fi wireless network at home.

In this article I will describe setting up Wi-Fi using the Dlink Dir-300 NRU B5 router as an example. The first thing to do is to the last. Then you need to configure the network on your computer/laptop to automatic acquisition of an IP address and DNS server. After this, we connect via web interface at Dlink (this applies to those cases if you closed the web interface after updating the firmware). We enter into the browser (it is advisable to use Internet Explorer or Mozilla Firefox) 192.168.0.1 login admin, password admin (default).
After this we get to the web interface of Dlink Dir-300 NRU. Click on the button « Wi-Fi Master wireless network settings".

In the first settings window you need to check the box "Turn on wireless connection», I think it’s clear why :). MBSSID parameter (allows one access point to serve up to four wireless networks at once with various settings) and BSSID (this is the physical address of the access point (MAC address) for the corresponding network.). At home, these functions are used extremely rarely, which is why they are initially turned off, and we will leave them as such. Click "Further".

In the next window in the line "Hide access point" We don’t check the box, write the name of the wireless network in the SSID line, select the country, leave the channel on auto or indicate free, how to determine a free channel is described in the article How to select/change the wireless channel on the router/router . Wireless mode choose « 802.11 B/G/N mixed» , in order to various devices could connect to Wi-Fi if the line "Maximum number of clients" leaving 0 means that an unlimited number of devices can connect to the Dlink Dir-300 NRU; if you specify, for example, the number 5, then maximum amount There will be no more than 5 devices that can connect to the wireless network.

In order for all devices, both new and outdated, to connect to the Wi-Fi networks, select network authentication "WPA-PSK/WPA2-PSK mixed".

In the PSK encryption key line, enter the password that you will need to enter in order to be connected to the Wi-Fi network (I recommend using complex password, at least 8 characters with letters, numbers and special characters). All other settings relate to encryption and I recommend leaving them at default.

In the next window we look at all the settings we specified, if everything is specified correctly, click "Save" otherwise press "Back" and fix it.

Now you need to save the settings on the Dlink Dir-300 NRU, to do this, press the button at the top "Save".

At this point, the Wi-FI setup on the Dlink Dir-300 NRU router can be considered complete, close the browser window, turn on Wi-Fi device, we find our network.
Enter the password and enjoy the Internet wirelessly.
After configuring the router, you can begin setting up the local network on

Every day more and more flows into our lives electronic devices, requiring constant access to the Internet: computer, laptop, smartphone, tablet, TV, etc. How all of them connect to the internet and at the same time pay as for one device, at the standard rate.

This will help us wi-fi router or whatever they call it Wi-Fi router.

In this article we will go through step by step, how to configure and connect the D-Link Dir-300 router to your provider based on a connection to the Dom.ru provider via the PPPoE protocol. Router D-Link Dir-300, is quite popular model among a wide variety of routers, or routers as they are also called, due to their stable work, good characteristics, reasonable price.

Setting up the D-Link Dir-300 router

Let's unpack the box with the router, remove its contents, the kit should contain the following:

• the router itself (router);
• cable (patch cord) to connect the router to the computer;
• power unit.

To organize the connection and configure the router, we additionally need:

• an agreement from your provider with login and password;
• settings data (connection type, protocol version);
• cable " twisted pair“, this is the one who brought the technician to connect to your apartment or house.

Connection

We take the router, plug in the power supply, wait until the green LEDs light up, indicating that it is in good condition. Connect one end network cable to LAN port 1, the other end to network card on the computer. We connect the cable from the Internet to the WAN (INTERNET) port.

Usually, new router comes with factory settings specified in the instructions or on the back of the router case (bottom). If your router is not new, then perhaps the previous owner changed it network settings and changed the router access password. In this case, if you still don’t know the settings, then the only way to access the router is to reset the router to factory settings, this is done by pressing a pin or toothpick on special button through a small hole labeled “reset”; you probably did a similar procedure when you removed a disk from a jammed CD-ROM. If you didn’t succeed in rebooting the router the first time, try holding down the “reset” button longer, and also give the router time to reboot from 30 seconds to 1 minute after releasing the button.

Settings network connection and login to the router control panel

In order to get into the control panel of the D-Link Dir-300 router, and not only this model, in the network connection settings in the TCP/IP Internet protocol you should specify “ Obtain an IP address automatically».

Path for Windows XP as follows:

Start > Control Panel > Network Connections > right-click on “Local Area Connection” and select “Properties” > in the TCP/IP Internet Protocol properties set “Obtain an IP address automatically” and “Obtain a DNS server address automatically”.

Path for Windows 7 looks like that:

Start > Control Panel > Network and Sharing Center > Change adapter settings > select Local Area Connection > Properties > Internet Protocol Version 4 > Properties > select “Obtain an IP address automatically” and “Obtain a DNS server address automatically.”

The above settings are similar in different operating systems, be it Windows XP, Windows Vista or Windows 7.
To log into the router control panel(router) D-Link Dir-300 open any browser and enter in the address bar http://192.168.0.1, after which a login window to the administrative section of the router will open. In the authorization pop-up window, enter the user name in the field admin, enter the password in the field too admin.

Setting up the Internet on D-Link dir-300

By entering your login and password, we are taken to the main page of the router settings control panel. The router configuration interface, depending on the hardware revision and current firmware may have different appearance. After that we need to go to “Advanced Settings”, the link is at the bottom.

In the page that opens we find the section “ Net" and follow the link " WAN»

On this page we see that one connection has already been created by default, it is disabled, we do not touch it, we need to add our connection by clicking on the Add button in the lower right corner.

Here the main task is to correctly select the type of Internet connection from the list (select a protocol from the drop-down list). Information about what type of connection your Internet provider uses can be easily found on its official website, or call technical support, where they should tell you step by step about setting up the router; perhaps all the settings will be given in the Internet access service agreement .

For reference, protocols that some providers use:

• Online - Dynamic IP, i.e. You don’t even need to configure anything in the connection, the only thing worth taking care of is the Wi-Fi password, which will be discussed below
• Beeline - L2TP + Dynamic IP
• Interzet - Static IP
• Rostelecom, Domolink, TTK, Dom.ru - PPPoE
• Stork - PPTP + Dynamic IP

In most cases, all that needs to be filled in in addition to the connection type is the login and password that you received from the service provider, for example, to connect to the Internet via the PPPoE protocol, it will be enough to enter the login and password issued by the provider and come up with a name for the connection, do not touch the rest of the settings need to.

After entering, click on the “Save” button. Once again we find ourselves on a page with connections, the last of which is just created, which, as we are shown, is “broken”. At the top right you will see an indicator indicating that the router settings have been changed and now need to be saved. You should do this - otherwise, after rebooting the router or turning off the power, all settings will be reset. Refresh the connection list page. If you have configured everything correctly, without mixing up the password or connection type, it will turn green and the Internet will become available.

Wi-Fi setup access points

If you are on the main settings page of the D-Link dir-300 router, then go to the advanced settings again. In the Wi-Fi section, check that the module itself is turned on (the switch is green in the picture and says On) and follow the link to the main settings.

On the page that appears, you need to specify the name of the access point SSID, by which you will recognize your wireless network among possible others. Since we will be setting up wireless network encryption and setting a password for accessing Wi-Fi, we should not hide the access point name. There are also other customizable parameters here, but you shouldn’t change them unless absolutely necessary. Click the change button and save the settings.

Now we need to protect our wireless network from random connections and “free Internet”. While on the advanced settings page, in the Wi-Fi section, click on the “Security Settings” link. Here we are interested in the “Network Authentication” field, select WAP2-PSK from the list. In the “PSK encryption key” field, set a password. The password must contain at least 8 characters and consist of numbers or Latin letters. Click the change button and save the settings.

Changing the administrator password

To protect your router from unauthorized connections By Lan networks or via Wi-Fi, necessary change the administrator password for the router. To do this, go to the “System” > “Administrator Password” section and change the password in the standard way.

On this, the most necessary settings For normal operation routers are completed, there are of course many more specific settings, but you shouldn’t change them unless absolutely necessary.

If something doesn’t work out for you or suddenly becomes unclear, you can watch this video on setting up the D-Link DIR-300 router:

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.0.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Changing the factory password

Default: Login admin, password admin.

In the router interface, you need to go to the tab System, menu Administrator password.

In field Password (New Password) Enter a new password.

In field Confirm Password repeat new password.

After this, the router will prompt you to re-enter its settings.

Setting up an Internet connection

On the page Advanced settings; select Net; ⇒WAN;.

Click on the button Add.

Setting up a PPPoE connection

1. In field Connection type: select PPPoE
2. In field Port select the WAN port - it is listed there as Port 5.
3. Username: Your login from the contract
4. Password: Your password from the agreement
5. Password confirmation: repeat password
6. Authentication algorithm: Auto
7. Keep alive
8. MTU

In field Miscellaneous NAT And Firewall .

Enable IGMP.

Setting up an L2TP connection

1. In field Connection type: select L2TP + Dynamic IP
2. In the Port field, select the WAN port - it is listed there as Port 5.
3. Username: Your login from the contract
4. Password: Your password from the agreement
5. Password confirmation: repeat password
6. VPN server address: enter the address of the provider's VPN server
7. Authentication algorithm: Auto
8. Keep alive- check the box for permanent connection
9. MTU- change the value to 1450 or less

In field Miscellaneous check that the checkboxes are checked NAT And Firewall.

If your provider provides Internet television service, check the box Enable IGMP.

Configuring PPtP (VPN) while automatically obtaining a local IP address (DHCP)

1. In field Connection Type: select PPTP+ Dynamic IP
2. In field Name enter the name of the connection (you don’t have to change it)
3. Username: Your login from the contract
4. Password: Your password from the agreement
5. Password confirmation: repeat password
6. Connect automatically: put a tick
7. MTU change the value to 1450 or less
8. Authentication algorithm: Auto
9. Keep alive- check the box for permanent connection
10. Save the settings with the button and reboot the router.

Setting up Wi-Fi on the router

1. From the advanced settings page, go to the tab WiFi, select the item basic settings; and set the desired name wireless point access SSID. After that, click Change;.

2. After this, it is also recommended to set a password for your wireless network. To do this, go to settings Wi-Fi security, select the authorization type (WPA2/PSK recommended), and then enter any password of at least 8 characters - this will help protect your wireless network from unauthorized access. Save your changes.

That's all: now you can try using the Internet via wireless Wi-Fi connection from a laptop, tablet or any other equipment.

Checking Internet connection status

If the connection is created correctly and there are no problems on the part of the provider, then in the column " Network information ", WAN connection status it will say connected and your IP address.

Saving/restoring router settings

1. Select saving the current configuration. To save the current settings of the router, the settings file will be saved to the specified location on the hard drive.
2. To restore settings from a file, you need to click and select Loading a previously saved configuration into the device, specify the path to the settings file, then click the button.