How to install a router: step-by-step instructions. How difficult is it to install a Wi-Fi router at home yourself? Everything you need to know before buying a Wi-Fi router


Setting up Wi-Fi at home is often a big problem. If you don’t want to cut off your phone number to your provider, follow the simple instructions and everything should work out. At best, setting up a router out of the box will take about 15 minutes. Shall we time it?

Important!For example, we took a router TP-LINK TL-WR840N . Program interfaces for setting up different models TP-LINK routers may vary slightly (not to mention routers from other manufacturers). Look for the menu items you need, and don’t be alarmed if yours is different from the photo instructions.

The fastest way to configure Wi-Fi router - not the one with the disk. Although an installation disk is included with every router, this installation is not available for everyone. We'll go the other way - let's see how to configure the router manually.

In order to successfully connect the router, you need to know the type and parameters of your Internet connection:

  • IP address;
  • subnet mask;
  • login;
  • password.

This information must be contained in the agreement for the provision of Internet services. There is no contract or the contract strangely does not contain any of the above points? We call technical support and find out.

Connecting a router

  1. We connect the router to the network (the power cord is included - is there one?).
  2. Press the ON button. on the router (many routers are also turned on directly from the outlet, but in vain). In our case, both the power adapter and the button are in place.
  3. In the box we find a network cable. At one end we connect it to the router (there are many ports on the router, you need the one labeled “LAN”,necessarythe port is also usually highlighted in a different color from the others). Others - to the PC network card.
  4. You need to enable automatic acquisition of an IP address. You can do it like this:

Router administration

  1. On a PC, open any browser (we used Google Chrome).
  2. We write the router address in the address bar (for TP-LINK Wi-Fi routers it is 192.168.0.1 or 192.168.1.1).
  3. In the window that appears, enter your username and password. Unless otherwise stated in the technical documentation or on the bottom of your router, routers typically use:
  • login: admin
  • password: admin


If you did everything correctly, this page is in front of you. The menu is always in English. On the left is the menu, in the center is the content of the selected item on the left, and on the right is an explanation and the most important settings items.

How to set up a Wi-Fi router at home

Don’t be afraid: you don’t need to fumble around in every section with an English-Russian dictionary at hand. All you have to do is tick 3 boxes.

Chapter Network, paragraph WAN. From the list, select your connection type - Dynamic IP, Static IP, PPPoE or PPTP (see contract). In our case it is PPPoE. Each type of connection requires tuning. Using the prompts below, complete the settings on your router and clickSave(at the bottom of the page).

PPPoE

Dynamic IP

Static IP

PPTP

Important!The provider is sometimes bound to the MAC address of the network card (a typical phenomenon for Dynamic and Static IP), so we additionally go to MAC Clone and press Clone MAC Address. This is in case you did everything as stated above, but for some reason nothing worked.

Setting up a Wi-Fi network

We have almost figured out how to connect Wi-Fi - all that remains is to configure the Wi-Fi network. So let's go toWireless- Settings.

We find our location in the list, come up with a name for this network (it’s better not to be clever with the name, but you can’t leave it “as is” - if it matches the name of a neighbor’s Wi-Fi, problems may arise).

Among other things that are on this page, the following menu items may be useful:

  • Enable Wireless Router Radio - enables/disables Wi-Fi;
  • Enable SSID Broadcast - enable/disable the visibility of a Wi-Fi network; if you disable this item, this network will not be displayed in a general search for Wi-Fi networks (only through the SSID).

The latter is not a way to hide from your neighbors, so don’t rush to be clever with secrecy.

Setting up Wi-Fi network security

We remain in the sectionWireless, go to the submenuSecurity. The optimal choice of parameters from the list is in the photo below. You only have the Wi-Fi password. We recommend that you write it down in the contract for the provision of Internet services (so that it certainly doesn’t get lost).

Connection and operation

You can, of course, also set up a local network and change administrator passwords (the ones that are admin/admin by default on all routers). But these are already bonus points. The majority of users can start working after rebooting the router. You can do this by clickingREBOOTin the message that pops up at the bottom of the settings page.

Now we connect the cable from the provider (through which the Internet comes to your apartment) to the INTERNET port, highlighted in color and labeled. Other ports are designed for wired connection of PCs and laptops that have problems with wireless.

Now you know how to connect a router in 15 minutes. By the way, how long did you have on your timer?

P.S. Indicators

Not all routers are built the same, but keep in mind:

  • indicator Systemshould flash, not light up;
  • Power- just burn;
  • the middle indicators are blinking - data is being exchanged, the indicators are on - there is no network activity, off - there is no connection;
  • Internet- lights up when there is a connection, flashes - data is being exchanged, doesn't light up - check the cable connection.

If you need a signal amplifier or, say, a Wi-Fi adapter, you can select wireless data transmission equipment for any occasion using the link below:http://price.ua/catalog454.html.

If you decide to install wi-fi at home, at work, or in any other place, then you definitely need to purchase a special device called a router. This is a special device that distributes wireless Internet at a certain distance. Routers are classified by power, number of connected objects, speed, range, etc. Therefore, if you want to purchase a router, be sure to check out its specifications. Once you purchase this device, you will need to install it. I am sure that 99% of users will have problems with this, so this article is dedicated to how to install a router.

How to install a router - step by step guide

There are a huge number of routers from different manufacturers, but the most popular are D-Link. That is why we will figure out how to install a D-Link wi-fi router.

1) Open the box with the purchased device, take it out and connect it to the power supply. The lights on the front should light up. If they do not light up, then there is some problem with the router. On the back side we see several ports. We need a port labeled “Internet”, into which we must insert the plug that was connected to the computer.

2) In any of the other ports we place the cable that was included with the router. This cable needs to be connected to the computer (to the place where we pulled out the Internet cable).

3) Open any program that provides Internet access. We write the following numbers: 192.168.0.1. This page is the main settings page. You don't need an Internet connection to connect to it.

4) We continue to figure out how to install the router. We have opened an authorization page with the fields name and password. In the name field we write admin, and leave the password field empty.

5) On the page that opens, select the Setup item, then the Internet Setup item on the left and then click Manual Internet Connection Setup.

6) In the Internet Connection Type section that opens, select the item called PPPoE user name/password and select the Dynamic PPPoE item. In the Name, Password and Password Confirmation fields, enter the data that is specified in the agreement with your Internet provider.

7) Look a little lower and see the “clone mac address” item. Click on it. In the Connect mode select item, put a dot opposite Always. The remaining items do not need to be changed.

8) Discussion on how to install is almost complete. All that remains is to figure it out. In the device menu, which is on the left, select the Wireless installation item, then the Manual wireless connection setup button will appear in the center, click on it and look at the main settings menu that opens. In the Wireless section, check the box next to Enable wireless network, and in the Wireless network name field, write any name. We also fill in the Wireless Network Key field and remember it. This field will store the password for your wi-fi. It is needed to prevent neighbors and other strangers from connecting to the router.

I hope that after reading this article, you have figured out how to install a router.

Nowadays there are a huge number of different Wi-Fi routers from different manufacturers on sale. And that’s good, there’s plenty to choose from. But immediately after purchasing a router, we need to install, connect and configure it. And if the connection process is practically the same depending on the model, then the setup process itself and the page with the router settings can be different even from the same manufacturer.

It is very difficult to give detailed and step-by-step instructions on setting up different models in one article. But I'll try. In this article I will describe in detail and show how to install and configure a Wi-Fi router. Regardless of what manufacturer and model you have. This universal instruction is suitable for both setting up a new router and re-configuring it. You can do everything yourself. And you don’t have to pay specialists for setup.

Login to the router settings. How to log into the web interface?

Each router has its own web interface (site with settings, control panel), which can be accessed through a browser by going to the appropriate address.

Important! To go into the router settings and configure it, your device (PC, laptop, smartphone, tablet) must be connected to the router via cable or Wi-Fi network. At the same time, there may be no access to the Internet on the computer. You don't need internet to log into the control panel!

If you have a high-speed connection on your computer (maybe with your provider's name), then after connecting through the router there is no need to start it!

To enter the settings we need find out the address our router and factory username and password for authorization. This information is located on the body of the device itself. It looks something like this:

On a computer or mobile device that is connected to the router, open a browser (Opera, Chrome, Yandex.Browser, etc.) and go to the address indicated on the case. Or try 192.168.1.1 and 192.168.0.1.

Important! We enter the address in the address bar, and not in the search bar. Many people get confused and instead of a page with settings they end up on a page with the search results of some search engine.

On the login page you need to specify a username and password. The factory settings are indicated on the device body. Most often these are admin and admin. On some models, the default settings are not protected, and immediately after logging into the control panel, you need to set a login and password.

Articles that may be useful to you at this stage:

If the settings page has opened, we can continue. If not, then see the article with solutions to this problem at the link above.

How to set up a Wi-Fi router?

In order to use the Internet through a router, you need at least:

  • Set up an Internet connection.
  • Set up a Wi-Fi network.

In most cases this is enough. I also recommend changing the password that protects the router’s web interface. There are also settings for IPTV, USB drives, parental controls, etc., but not everyone needs them.

In the control panel of almost every router there is a so-called “Quick Setup Wizard”, also known as “Quick Setup”. On some devices, it opens immediately after logging into the control panel. With its help, you can configure your Wi-Fi router step by step. Internet connection, wireless network, etc. For example, what it looks like at TP-Link:

You can try it, it's very convenient.

Internet setup. The most important step

The main thing is correctly configure the router to connect to the provider. If he cannot connect to the Internet, then all devices will have a “No Internet access” connection. Many users who try to configure everything themselves most often encounter problems at this stage.

Each Internet provider uses a specific type of connection. Dynamic IP (DHCP), Static IP, PPPoE, L2TP, PPTP. This type of connection must be specified in the control panel of the router, and certain parameters provided by the Internet provider must be specified.

Important! You must know exactly what type of connection your provider has. Also all the necessary data for connection (Username: Password), if they are necessary. As a rule, this information is specified in the contract that you received when connecting to the Internet.

Some providers bind by MAC address. It would also be desirable to clarify this.

If your provider uses a “Dynamic IP” (DHCP) connection, then the Internet should work immediately after connecting, since this type of connection is set by default on routers.

If the Internet through the router is already working (and you haven't run any connections on the computer), then you can skip this section and go straight to setting up Wi-Fi.

When the connection type is PPPoE, L2TP, PPTP, or Static IP (which is very rare), then you need to set the necessary parameters. Usually, this is the login and password that your provider gave you. In the control panel, the section with these settings is most often called: “WAN”, “Internet”, “Internet”.

For example, what the PPPoE connection setup looks like on an ASUS router:

Other examples:

Target: so that the Internet through the router works on all devices. Via cable and Wi-Fi. If this does not happen, then there is no point in continuing the setup.

You can always call the provider and clarify what parameters should be specified and where. They help many people over the phone.

Articles that may be useful to you:

I hope everything worked out for you.

Changing Wi-Fi network settings

I highly recommend changing your Wi-Fi network name and password. It is also advisable to set your region. Everything is simple there. This can be done in the section with wireless network settings. It can be called differently: “Wi-Fi”, “Wireless network”, “Wireless”, “Wireless mode”. If you have a dual-band router, then the settings must be set separately for the network at 2.4 GHz and 5 GHz.

  • In the "Network name" (SSID) field you need to enter a new name. In English letters.
  • In the "Password" field (wireless network key) create and write down a password. Minimum 8 characters. Security type - WPA2 - Personal.
  • Well, there should be a “Region” field there. Change it to yours.
    • IPTV on ASUS routers.

    If something doesn’t work out for you during the setup process, you can always reset the settings to factory defaults and try setting everything up again. Find the “Reset” or “Reset” button on the case, press it and hold for about 10 seconds. The indicators will tell you when the reset occurred.

    You can leave questions in the comments. I just have a small request, describe the problem in detail. Write the router model. Otherwise, it’s very difficult to understand and advise something when you don’t understand the question itself. Best wishes!


2024 gtavrl.ru.