How to connect a wireless router to a computer. How to connect and configure a Wi-Fi router? Step-by-step instructions for all models

Not so long ago, a computer, and especially a laptop, was a luxury. Today, almost every family has a computer or laptop, and in many families almost every family member has these devices. Each such device must have access to the Internet, since a computer without the Internet is a “box”. With the development of technology, in order to divide Internet traffic into several devices, it is no longer necessary to connect a separate cable to each device; everything can be done over the air - using Wi-Fi technology.

The content of the article:

Benefits of Wi-Fi

Before we talk about setting up a Wi-Fi network at home, we’ll talk about the tasks and advantages of this technology. So, if you need to divide your existing Internet channel into several devices, then you need a router. If you want to share the Internet channel by connecting devices without using wires, then a Wi-Fi router will help you with this. We have already told you about this and therefore, before purchasing it, we recommend that you read this article again. A Wi-Fi router is a great option if you have devices that support Wi-Fi networks. Thus, by installing a Wi-Fi router at the most central point, you can provide Wi-Fi coverage throughout the entire apartment, which is very convenient, because you will not need to run unnecessary wires. If your computer does not have Wi-Fi adapter, then this issue can be solved in two ways: install a Wi-Fi router in the room where the computer is located, or purchase a Wi-Fi adapter. Wi-Fi adapter is small sizes a device in the form of a flash drive or in the form of a card inserted into a PCI slot.

In view of the fact that almost every family has a need Wi-Fi installations router, then we will tell you how to configure it yourself, without calling a wizard.

Setting up a Wi-Fi router

To configure the router, it must be connected via a cable to a computer or laptop. The connection diagram must be shown in the instructions. We unpack the router, screw the antennas to it, then connect one part of the network cable (which comes with the kit) to the router, and the other to the computer (laptop). Then we connect the power to the router and after that we connect to it network cable Internet provider.

How to enter the router menu

Absolutely all Wi-Fi routers are configured using a WEB interface, this is a kind of website with settings. That is, in order to configure the router, you need to open the page with its settings in your browser. For this purpose in address bar browser, you must enter “192.168.1.1” and press the “Enter” key. After this, a window will appear on the screen in which you will need to enter your login and password to access the router settings. Standard (by default) login and password from the router settings menu: “admin” - in small letters. After entering, click “OK” and get to the menu.

Reflashing a Wi-Fi router

So, in order to set up a Wi-Fi router, you first need to reflash it. If you are a fairly experienced person and know what and how, then now we will tell you what you need to do for this. If you don't really like to understand all the intricacies computer equipment, then you can do without flashing the router. Firmware is a kind of operating system router on which its operation is based.

Why is flashing needed? Reflashing the router is necessary to ensure normal and high-quality operation of the device. As a rule, every Wi-Fi router has the same firmware version from the moment it is released until it is discontinued. This firmware only passes internal tests, but when the device goes on mass sale, users find all sorts of problems in the operation of the device in various situations. Therefore, the “native” firmware is not perfect and you may have problems with the device: low speed, freezes, problems with Wi-Fi, etc. That is why it is better to install a new firmware version.

In order to reflash the Wi-Fi router, you need to download the firmware file. Of course, you can download it from the manufacturer’s official website. To do this, on the website of the device manufacturer, find the model of your Wi-Fi router, and click on the “Downloads” tab; this is where the list of available firmware should be located. Some manufacturers may send you to an FTP server where the firmware is stored. But do not rush to download the latest firmware version, first read the forums where users who have installed this firmware, wrote a review about its work and came to a conclusion: is it worth installing or not.

After downloading the archive with the firmware, unzip it and copy the firmware file to the downloads folder. In the router menu, go to the Firmware section and in the available field, specify the path to the router new firmware. More detailed instructions You can find information on how to reflash the router in the instructions for the device.

After flashing, go to the Network / IPConfig / Network menu (depending on the model of your router) and first enter the provider settings.

WAN connection type

• Dynamic IP / DHCP / Dynamic IP – select if the provider provides dynamic IP;


• Static ip / Statistical IP address - select if the provider is built on local network, where to access the Internet you need to enter the IP address, subnet mask and Gateway.


• PPPoE – select if you need to enter a login and password to access the Internet.

DNS

DNS 1 and DNS 2 - it is advisable to leave them installed automatically if the provider requires them manual installation(which is very rare), then enter the primary and secondary DNS. It is not always necessary to enter the provider's DNS in the network settings; sometimes external DNS work better than the provider's.

Then go to the Wireless tab, which contains Wi-Fi settings.

How to setup Wi-Fi network

Network name (SSID)

Network name is the name of your Wi-Fi router, which will be displayed when the device searches for a network to connect to Wi-Fi. We recommend that you set the name as original as possible to avoid coincidences. If you have a network with 2 devices with the same names, then it is possible incorrect work Wi-Fi connections.

Channel

This is the frequency channel over which data transmission will occur. Please pay attention to this parameter Special attention, as this may cause you to have low speed via Wi-Fi. Why? Each channel has its own, so to speak, data transfer volumes. The more of your devices are connected via Wi-Fi, the lower the Internet speed for each device - the same goes for the channel, the more devices use the same channel, the lower its bandwidth. Therefore, even if you high speed connection to the Internet, and the Wi-Fi channel is overloaded, then Wi-Fi speed connection will be very low.

If your neighbors are not so advanced, then this parameter can be left at “Auto”. It’s very easy to check the Wi-Fi activity of your neighbors - call up the Wi-Fi connections menu list and look at the number of Wi-Fi routers that are available in your apartment: if there are few of them, then the channel is enough, if there are many, then it’s better to install it manually.

Since “Auto” selects the 6th or 7th channels, when manually selecting it is necessary to select the channels located at the beginning. That is, if in the future the Wi-Fi connection speed drops, but the cable connection speed is as stated, then it is possible that the whole problem lies in the Wi-Fi channel.

Wireless Mode

This parameter sets the standard wired network. Two factors depend on the wireless network standard: the ability to operate old-type devices in it and Wi-Fi speed. That is, Wi-Fi has its own standards of operation, and to make it more clear to you, let’s look at an example. In cellular communications, first the Internet was transmitted via WAP, then via GPRS, then via EDGE, etc., with each new type the data transfer speed also increased - in our situation everything is the same. The further a letter in the alphabet represents a communication standard, the higher the data transfer rate it supports. But here it is necessary to take into account one more point: not all devices released quite a long time ago and supporting work in Wi-Fi networks support the latest type of connection - and this must be taken into account.

Choosing a type demon wired communication, set the type that will be supported by all your Wi-Fi devices ami. Newer types of devices can work with older types, but not vice versa. But don't be upset, most modern Wi-Fi routers can work with several standards - which is very convenient; to do this, set the value to “b/g/n” (if available).

Channel width

The channel width is indicated in megahertz. We recommend leaving this parameter at “Auto”, or setting it to its maximum value.

Maximum data transfer rate

This parameter sets maximum speed data transfer - speed limit. Of course, it is best to set this parameter to maximum value. If you are the main Internet user, and you need high speed data transfer via a network cable on your computer, then you can reduce the speed via Wi-Fi in this way.

Encryption type

Another important parameter when setting up a Wi-Fi router, the type of encryption of the transmitted data. The stronger the encryption type, the more securely your data will be transmitted. By far the most the best type encryption is WPA-PSK/WPA2-PSK. But here you should also pay attention to the fact that not all devices support this type encryption and therefore it is possible that when choosing it you will need to find a “golden mean” for all devices.

How to set up Wi-Fi on a computer and laptop

Let's briefly tell you how to set up Wi-Fi on Windows 7 and Windows 8. In order to set up Wi-Fi on a laptop or computer, you need to select your Wi-Fi router in the list of Wi-Fi devices, to which you gave the original name. Then we click on its name 2 times with the mouse, and we are prompted to enter a password - enter the password, it is checked, and if you entered everything correctly, the device connects to Wi-Fi. After this, we recommend checking both over the network and over Wi-Fi. Please note that Wi-Fi speed may be limited throughput router. Therefore, it may differ from the one available over the LAN.

Sometimes, to connect a laptop via Wi-Fi, you need to separately enable the Wi-Fi module. As a rule, on laptops the corresponding button is responsible for this; it can be either separate or combined with the F7 key.

You can find out more detailed information about setting up a Wi-Fi connection from the video below.

The question of how to connect a wi-fi router to a computer is asked by users when they want to use the Internet throughout the apartment and have free access to the wi-fi network from several devices.

In addition, they are interested in how many computers can be connected.

Installing and connecting a router is a simple process, which, however, requires careful adherence to the algorithm of actions.

Router installation

Installing a router can be done in two ways:

• via wireless network;
• using a twisted pair (a special wire that usually comes with the device).

The second method is less preferable. In order to make a connection, three main components are required:

1. Actually a wi-fi router;
2. A desktop computer or laptop with an installed network card;
3. Network cable.

If you need a wi-fi router only to use the Internet from your phone or tablet at home, then these are quite suitable for you inexpensive models routers designed for 4–6 devices.

However, still pay attention to how many computers can be connected to the network at the same time.

Advice! Special requirements It is worth presenting to the device if you plan to store data. Also, when choosing, it is worth checking what speeds the device supports; they must be gigabyte. Otherwise, working on the Internet will become very difficult.

Wired connection

Connecting a router using twisted pair is quite simple, but with such a connection its operation becomes much more complicated.

In particular, you will not be able to move the computer away from it more than a certain distance.

Therefore, this option is not applicable for laptops. But it may be a good solution if you have a desktop computer.

This wi-fi connection has its advantages. For example, it is believed that in this way the Internet causes fewer interruptions during operation.

• First, connect an Internet cable to the router.
  Find the WAN port on the back of the device and plug the cable into it. Then take the network cable and connect it to the router into the Ethernet port, and the other end into the corresponding port on the computer.

• Set up your router.
  Open any browser and enter the device's IP address in the address bar. The address must be in the format . The true IP of the router can be found on the sticker on the bottom or in technical documentation to the equipment.

After the IP is registered, the setup program will require you to enter your login and password.

Then you can change the password for convenience. After this, the main wired network settings menu opens.

Important! If you are using wired connection, then pay attention to the number of connectors in the router. How many there are - so many computers you can connect to the device.

Wireless connection

If you intend to connect your Wi-Fi router wirelessly, you will have to set up the connection in two stages.

The first of them is the actual settings, and the second is work on network security.

• In the router menu, open the “Wi-Fi” tab, and there find a tab called “ Manual setting parameters". The names of the tabs may vary depending on the type of router, but their meaning is usually obvious.

• In the main settings we find the SSID field. We write the network name in it. This is the name that you will see when connecting to the Internet from any device. Set the correct region in which the wi-fi network will work.
  Next, you need to select a channel for data transmission. It is better to leave the one indicated initially. However, over time it can be changed if problems arise with access to the Internet.

• Choose wi-fi standards. It is advisable to leave the mixed ones installed by default. Now choose how many network users can connect several computers to it at the same time.
  If the number of users should not be limited, select “0”.

• Go to the “Security” or “Security Settings” tab. In the field at the top, select the type of protection. WPA2-PSK will do. Enter the password in the “Key” field. Such measures will protect you from hacking and from those who like to use the Internet at someone else’s expense.
  Only someone who knows the password can connect the device to the network.

The advantage of this method is that you can use the Internet throughout the apartment.

And, in addition, only with this type can you connect a second, third, or more computers located far from the device to the network.

If the power of the router is not enough for stable Wi-Fi coverage of an apartment, home or office, there is a need for additional devices. There are three ways to enhance weak signal main router: install additional antenna, repeater or another router. Each method has its own advantages and disadvantages; let’s take a closer look at the third option.

How to set up a router

To configure the router, connect a computer or other device with a web browser installed to it:

• You can connect your computer with a cable by connecting the PC’s network card to a free LAN port of the router;
• You can connect to the router via a wireless Wi-Fi network using a laptop, tablet or smartphone.

By default, the wireless network is assigned a name (SSID) identical to the name of the router model, and access to the distributed Wi-Fi network is not protected by a password.

After establishing a connection with the router, open it on your computer or connected wireless device web browser and type the router's IP address in the address bar. For example, for a router TP-LINK address will be as follows: http://192.168.0.1

The illustrations are taken from the settings of the TP-LINK TL-WR 1045 router; the control panel of other manufacturers looks different, but general principles, abbreviations and terms will be the same.

Entering the router's IP address in the browser's address bar will open access to the control panel

The correct IP address, login and password required to log into the control panel are indicated on the plate attached to the bottom of the router.

The IP address, login and password of the control panel are indicated on the nameplate on the bottom of the router

The login and password indicated on the sign apply only to the control panel, but not to the wireless network distributed by the router. After entering your login and password, you will see main screen, which displays information about the device status and provides access to menu items for setting modes.

Do not change the factory settings of the router unless necessary. After making changes to the router settings, reboot the device.

Video: setting up a Wi-Fi router

Two ways to connect routers

Routers are connected to one local network either by cable or by wireless channel. It is recommended to use devices from the same manufacturer.

Cable connection

Cable " twisted pair"(UTP cable) is laid between the main and additional routers. In the main router, the cable is connected to the LAN socket, and in the additional router - to the WAN socket (this socket is highlighted in color and is sometimes called Internet). With this connection, the additional router will be a network device for the main one, and the main router will act as a provider for the additional one, distributing the Internet and providing a dynamic IP address.

Before installing an additional router, consider how the cable will be laid and carefully measure the length of the future cable channel. When purchasing a cable, buy one meter longer than measured cable channel, and ask the seller to immediately crimp the ends of the cable into the connectors. If the cable channel runs outside the premises and is exposed to natural influences, then purchase a cable with a reinforced sheath.

Advantages of the method:

• reliability and stability of the cable connection;
• easy setup of both routers;
• The installation location of the additional router is not limited by the wireless coverage area of ​​the main router.

Disadvantages of the method:

• the need to purchase and lay cables;
• When moving the router, the cable will have to be moved to a new location.

Configuring routers when connected by cable

If the main router is already configured to work with the provider and there are no complaints about the work, then there is no need to change anything in the settings.

Make sure that the DHCP function in the main router is enabled for automatic distribution IP addresses on the local network. The start and end IP addresses do not need to be changed.

Setting up an additional router

It is recommended to immediately reset any changes made to the router settings to those preset by the manufacturer. To do this, turn on the router, find the Reset button on the rear panel, press and hold it pressed for 5-7 seconds. To protect against accidental reset of settings, the button is hidden inside the case and can be pressed through the hole using a needle or an unbent paper clip.

An example of the location of the reset button on the back panel of the router: the button is hidden inside, only the hole for pressing is visible

In the additional router, two settings are checked and set:

Making changes to the additional router’s own IP address allows you to avoid conflicts of identical addresses on the same network

After changing the router's IP address, to re-access the control panel, enter the new address in the browser's address bar.

There is a cable connection option in which the cable is connected to the LAN port of an additional router. This option requires complex setup and does not provide any advantages over a WAN port connection.

Wi-Fi connection

Advantages of the method:

• does not require physical connection routers with cable;
• makes it easy to move if necessary additional router.

Disadvantages of the method:

• relative complexity of setup;
• slowdown in wireless network speed.

The main router receives Internet from the provider and distributes it via the wireless network LAN1; the additional router receives the Internet wirelessly from the main router and distributes it via the LAN2 wireless network

Configuring routers when connecting via Wi-Fi

When two routers are connected on a local network via a wireless channel, a “bridge” connection is used, in English Wireless Distribution System (WDS), designed specifically to expand Wi-Fi coverage area.

Understanding Bridged Connectivity (WDS)

When installing this type of connection, the main router operates in standard mode, and the additional one performs the function Wi-Fi booster, receiving and distributing the signal further.

To connect routers in bridge mode, you need to establish a permanent (fixed) communication channel between them and specify the physical addresses of the connected devices in the settings. To set up a “bridge”, both routers are turned on, the main router is configured in advance for the provider, receives and distributes the Internet, and the settings of the additional router are pre-set to the factory settings by pressing the Reset button.

Configuring the main router for WDS mode

Mode automatic selection We change the broadcast channel to a fixed channel mode (for example, to the 11th channel).

Installation fixed number channel prevents the router from automatically scanning the air and selecting the least loaded channel. Therefore, if strangers work nearby wireless network, you may have to manually experimentally select the least loaded channel or use special program to search for a free channel. The channel number must be changed simultaneously on both routers - the main and additional ones.

Setting up an additional router for WDS mode

On home page In the router control panel, the “WDS Status” line should display “working.” This means that the additional router has connected to the main router and is distributing the Internet.

Video: how to make a Wi-Fi network between routers (WDS)

Creating a complex network requires knowledge and experience. If you are confident in your abilities, use our instructions. If you doubt your abilities, it is better to ask for help.

Today, perhaps, you will no longer meet a person who does not use a computer or does not have a PC at home. In addition, more and more services and programs necessary for work and leisure work when connected to the Internet.

also in Lately The situation is becoming increasingly popular when an apartment, house or office has not one device, but several (PCs, tablets, communicators, smartphones, etc.), each of which requires its own separate connection to the network.

The ability to connect several devices to the internet, while having one input signal point from the provider, is currently achieved using a router or router.

The router itself is network device, the purpose of which is to transmit packet data between devices paired with it and the access point - the service provider. In addition, more expensive routers are equipped with a number of additional functions, among which:

• the ability to set restrictions on access to sites that are potentially dangerous for software;
• ability to connect a firewall;
• the ability to encrypt network access and traffic distribution;
• ordered distribution of traffic across access points, etc.

A standard router, which can often be found both in a private home and in a company office, public places ah, is a small-sized equipment consisting of a hardware unit, an antenna for Wi-Fi transmission signal, power supply for connecting to the electrical network, patch cords (patch cords).

Photo – Equipment and connection of the router

A standard router is capable of organizing a network by connecting 4 PCs via wired communication, as well as 5-10 devices for which channels will be allocated Wi-Fi signals. However, experts do not recommend completely loading the router, especially if it is not an expensive model of this device. Otherwise, the router may freeze and cannot withstand heavy loads.

Some router models may be equipped with USB ports to connect a flash drive to them or hard drive. This feature will allow you to use the equipment as a file server, print server, etc. Besides, individual models They also boast support for 3G modems.

What you should pay attention to

When choosing a router, you should consider the following features and operating parameters of this equipment:

• for organization home connection or a network for a small office, a regular (non-professional) router from the mid-price range will be sufficient;
• device support for IEEE 802.11g and IEEE 802.11n standards is required will provide data transfer speeds via Wi-Fi up to 600 Mbit/s;
• installation must support PPTP or L2TP, which will provide access to Internet communications from almost any provider.

How a wireless Wi-Fi router works

The principle of operation of the equipment is based on receiving and converting the recipient's address, which is “written” in the header of the information packet for its transmission, then the path along which the information is addressed is determined using the routing table. If the routing table does not provide any address, the information is not accepted and discarded.

Photo - Example of a user network working with a router

In practice, there are some other systems for transmitting data to devices paired with the router. For example, using the sender address or protocols upper levels headers. There are also cases when the router’s operation is based on the transmission of addresses of both the sender and the recipient, as well as filtering the transit stream of transmitted data.

How to install a Wi-Fi router: step-by-step instructions

In order to connect and configure the router yourself, you need to do the following:

1. The first thing they do to install the equipment is to connect all communications from the router to the PC and to the Internet signal transmission unit from the provider. To do this, insert an Internet cable into the connector called WAN, and insert the cable that comes with the router into one of the remaining ports; its other end is intended for the Ethernet connector on the back panel of the PC. After this, turn on the power to the device.
2. Next move on to configuration software router. The equipment setup is not standard and may differ depending on the router model and connection settings from the provider. Configuration can be done through any browser installed on your computer ( Google Chrome, Opera, Internet Explorer, etc.). To do this, you need to go to the administrative interface of the device by entering the combination of numbers in the address bar of the browser: 192.168.1.1. After pressing the Enter key, the equipment administration window should pop up. If this does not happen, then you should check the cable connection, make sure that the connection is running, and then try again.
3. The next step is directly Wi-Fi setup connections. If the router is equipped with a function quick setup, then you need to start the “Quick Setup” service and follow the prompts of the installation wizard. Among the setup steps there will be a choice following parameters: — type of preferred connection;

   — type of Internet connection;

4. Next you need to connect directly Wi-Fi module. To do this, the installation wizard offers the following menu.

Photo - Module Wi-Fi connections signal

After these steps, the Internet connection should already be working. However, if the Internet speed is low or constant signal loss occurs, experts recommend choosing a specific channel (from 1 to 13), saving the settings. It is also worth taking care of the access password to the signal of the router you are connecting. Otherwise possible unauthorized connections, which will also reduce traffic and make the router work slower.

After the router is connected and configured, all that remains is to connect the work network card on a PC or laptop and use the device with the internet. On a laptop, you need to make sure that you press special key, including Wi-Fi mode. If this operation completed, you need to connect the device to the network.

Photo – Network indicator

To do this, on the desktop toolbar on the network icon, click right click mouse, select a name from the drop-down menu established network, click the “Connect” button.

Photo - Context menu with Internet networks installed on the device

The connection is made in a similar way for Windows 8; for other systems, the device is put into operation according to a similar scheme.

How much does a router for a computer cost?

Today, the electronics and computer equipment market offers its customers wide choose routers that differ from each other both by manufacturer and by some functional features of the device. These could be routers for a home network with a few connected devices or industrial equipment to provide access to the Internet for public places and large offices. Accordingly, considering functionality device, the cost of devices will vary significantly. By visiting a store or online store of electrical goods, the client can choose the appropriate equipment that will meet the requirements for it. At the same time, he will need to deposit an amount of money ranging from 1 thousand rubles. for a standard model up to more than 25 thousand rubles. for professional multifunctional devices.

Welcome, dear readers of our site. We continue the series of useful articles on setting up equipment.

Most users who want to connect a router to a computer or laptop face the problem of connecting the router due to ignorance simple functions this device. Smart-Tronics will tell you how to properly connect the router. In fact, everything is simple, read on!

What can you connect your router to?

This part of the article is for those who want to know more about how multifunctional a modern router is. What can I connect the router to? Here is a general list of devices that can be connected to the router (this is its second name):

• Computer
• Laptop
• Game console
• Smartphone
• Tablet
• EBook

Here are the main devices to which the router can be connected. Why is such a combination of all kinds of gadgets needed? To seamlessly exchange information between devices and have access to the Internet on each of them. You can connect the router using two different technologies: wired and wireless. The connection method depends on what kind of router you have (whether it has Wi-Fi support) and your desire. In this article we will talk about connecting a wired network. About wireless technology read in others, no less useful publications on our website - .

So, today, quite a lot of companies produce routers. At your choice, you can connect a router from Asus, D-Link, Zyxel, Trendnet, 3COM, TP Link, Netgear and others. We want to say right away that no matter what brand you decide to purchase a device, its connection will be the same as that of an alternative manufacturer.

Standard router connection

Let's describe the functionality of a regular router. This will help you understand what the connectors on your router are for and how to use them. How to connect the router correctly? It's simple! Let's look at the picture:

For correct connection, via a network cable, you need to do the following. Instructions for connecting the router:

1. Crimp correctly twisted pair(UTP network cable) if necessary.
2. Connect the router to the power supply.
3. Connect network cables.
4. Set up the network.

Read about network tincture in the article. Now, let's figure out how to connect the router to the computer.

How to connect a router to a computer or laptop

So, you have a special patch cable that will connect the computer and the router. Naturally, it must be compressed the right way, according to the required scheme so that the router and computer “see” each other. The patch cord needs to be plugged at one end into the network card of a computer or laptop, and the other into the router. Where exactly is shown in the picture. It also shows where to connect the Internet cable in the router. Diagram for connecting the router to a laptop or computer:

Isn't it simple? You can connect four to the router in the screenshot various devices via cable, not counting Wi-Fi connection. We hope the article was informative!

• Denis

  Tell me what could be the problem. I can’t find, either with a book or a smartphone, my router via Wi-Fi... Maybe tell me in the settings, I did something wrong... Everything works well, I installed the router via a computer, but connect other devices (((

• Smart-Tronics

  Denis, usually, with a correctly configured router, the network is found automatically on a laptop or smartphone. All that remains is to enter the password and connect.

• Max

• Smart-Tronics

• Vitaly

  Guys, can anyone tell me the ancient one has everything installed, installed the firewood, found the router. I want to use the Internet without a wire through a router. I tried to connect another tp link router, also through the cord there is a network itself via the radio channel I see the network I can’t log in, or should I remove the configuration wood and try to connect it again?

• Vasilisa Baranova

• Igor

  My provider is UTK. I enjoyed D-Link modem, everything was fine. Recently bought Wi-fi router TP-LINK TD-W8961ND. Through installation disk Can't configure! Through the browser too. Help! Now I'm sitting like this: I connected my old D-Link to TP-LINK as a computer in port 1, the computer itself is connected to port 2. There is Wi-fi, the Internet is on the computer too. But it shouldn’t be like that! One TP-LINK needs to work.

• Leah

  Hello. Please tell me how to connect the router to the laptop myself, so that there is no need to connect wires to the laptop. Thank you in advance.

• Alexei

  Hello. I can't open the admin panel of the router ( ASUS model DSL-G31). When I specify the address 192.168.1.1 in the browser, the browser cannot find such a page. The instructions do not say a word about the address that needs to be specified in the browser. True, there is a footnote that Gateway: 192.168.1.1, DNS: 192.168.1.1. Please tell me what can be done in this situation. Thank you in advance.

• su_yuri

• Tanechka

  Hello. The computer does not see the router. Writes: check wired connection between PC and router. I checked everything, all the wires are inserted in the right place. Please tell me what is the problem?

• Michael

  Please tell me... I have this problem, when I connect the laptop to the router it gives an error... that Windows cannot connect to the DIR300... although any other laptop connects... at first it was the adapter in the laptop, but then I checked it on other points, it works... what's the problem ?

• Laura

  Hello! Please tell me:
  Available d-link switch dir100, a fiber optic cable from the provider is connected to the wan port, a desktop computer to 1 port, lan-ip television to port 2. Need to connect tp-link router with wi fi to distribute the network to a laptop. How to properly connect all devices?

• Dmitriy

  Hello. I use the Internet on a laptop linked to a Mac address. I bought a router with wi-fi and 4 Lan outputs. I cloned the poppy address in the router settings and connected the laptop, both via Lan and Wi-Fi without any problems. Set-top box and phones are also no problem. I can’t connect a desktop computer with XP via Lan and it doesn’t see the network at all - what should I do? Thank you.

• Sanych

  I can't figure out which wires need to be connected to the router and from it to the laptop. Do you also need wired internet, or a home phone, or something like that???

• Ivan

  Good day! Tell me, is it possible to configure the router only FOR AND WITH THE HELP of a laptop, without resorting to a stationary computer? That is, there is simply no PC. Just a laptop, router and cables, what to do in such a situation?

• Juliet

  Good evening, tell me, you have configured the TRENDnet 652 router, the laptop sees the Internet, but the smartphone and the second computer do not connect, but see the router’s network.

• Sergey

• Maksim

  Hello! The Internet on the Beeline computer works fine, I connected and configured the d-link dir300 router, I can find wi-fi through my phone and tablet, everything connects well with a password. But the Internet, whether on the phone or on the tablet, does not work! IN network settings I tried to check the box to allow other network users to use the Internet connection of this computer(it has been removed). If I install it, the computer cannot connect to the Internet. (

• Julia

  Hello! There was a problem, the d-link router was connected and worked fine. But now for some reason the laptop does not connect to the router. It says that Windows cannot connect. What could be the problem?

• rock_stranger

  Hello. I have a question for you asking you to help me. I want to make a HOME network at home via WiFi. There are 3 laptops at home, two of them with Windows 7, one with Windows 8 and a stationary windowsXP (which is connected via installed WiFi antenna). Everything is configured on the WiFi router and works without problems with the Internet connection. How should I proceed and through what and where to enter data, if there is an opportunity to visually show the entire network in detail. Because I can’t figure it out from a minimal description. Thank you very much in advance.

• Sergey

  Hello!

  I have a TL-WR740N, when I go through the Easy Setup Assistant installation, I get the error “The router could not be found. Please check network. Please check your router model." All of these items are fine. Can you please tell me what to do?

• GT_Smart

  I have a major problem with my computer. My computer does not receive a signal from the router. First it says that a connection is in progress, and then the connection is interrupted and it says that it is impossible to connect. What to do? Tell(((((

• Vlad

  Hello, I am connected to the Internet on my computer via a USB modem, and it works fine. There is also a wi+fi router, but it does not have USB port for the modem. How can I connect a router after the computer so that I can use the Internet on my smartphone via Wi-fi? Help me please!

• Konstantin

  Hello! I connected a computer, laptop, netbook through the router, everything is fine. There were problems connecting the tablet! It sees the network, but after entering the password it says “connection to IP address” and there is no access to the Internet. Tell me what to do?

• MICHAEL

  Hello everyone)) I have the following problem: through the laptop I see the router and log into it, but through the desktop computer I can’t log in through the wire. How can I make my desktop computer work via a wired router?

• Dmitriy

  Hello, I'm coming in router dir 620, in the admin panel of the router, usually this is the IP address 192.168.0.1, through the browser, entering the login and password, it opens the settings and immediately returns to the login. What could be the reason?

• Alexander

  Hello. You need to connect a TP-LINK WR340GD Wifi router, but the problem is that the computer is using Satellite Internet. The connection occurs in this way: first, using any USB modem (operator), an Internet connection is established, then using the Globax5 program, a connection is made to the satellite, the satellite dish is connected to the computer coaxial cable via internet card. Tell me how it is possible to connect the router and configure Wifi.

• Antby

  Hello. This is the problem: I connected a USB printer to the router and, without any problems, according to the instructions, set it up for a laptop running Windows 7. I also tried to set it up for a computer running Windows 8, but it didn’t work - I entered the router’s IP in the address bar of the explorer, and instead of getting to the device, I get to its web interface. I just need to get to it through the explorer in order to further select and connect my printer. Maybe I explained it chaotically and I understand that most likely the solution is the simplest, but I can’t find it. Zyxel router keenetic giga, computer connected by cable, laptop via Wifi.

• Elena

  I looked at everything here... There are adaptive firmwares that include additional modems, but I can’t figure out if my modem is there or not. [...]

• Ksenia

  Good afternoon Purchased Wi-Fi D-Link router DIR-615, connected the provider's cable to the Internet port on the router. The blue cable from the kit has one end into the LAN on the router, the other into the port on the laptop where the provider’s cable was previously inserted. Now I can’t go to the router page 192.168.0.1, because... It says no internet connection.

• euro

  Hello! Problem. I have a laptop without wifi. There is a wifi distributor at work. Can I remove the wire from a working wifi and insert it into my network so that I can have internet. And how can this be done? Thanks in advance, I have Windows 7 home.

• Valeriya

  I bought a router, connected all the cables, entered the IP address into the browser, everything opened, started setting up, and a window was displayed to me, where it says that the Internet cable is not connected to the Internet port, what should I do? (everything is connected)

• Vitaly

• Vitaly

  The point is that I live in rural areas and it’s unlikely that such internet will be provided to us, but how does my son fall under the distance learning program? And just recently I found out that the Moscow provider LLC will provide us with our network satellite dish for training. That’s why I asked this question, but still, you can somehow connect it, because there is some way out.

• Nastya

  Hello. Today I connected the router, everything seems to be in order, the phone sees and finds the network and connects. Everything is fine, but it doesn’t connect to any Internet page. Why?

• Elena

  I’m probably writing in the wrong place, but still. Hello, I have the same problem, I stupidly downloaded it today connectify program on the computer (wired Internet) and deleted it immediately. But after that I can’t log into the Internet, as soon as I log in a window appears asking me to enter my login password, a message from the broadband router. As I understand it, there is some kind of router left, I can’t find anything related to it, tell me how to solve the problem.

• Kirill

• Vitaly

  Hello. After cleaning the laptop antivirus program The connection between the laptop and the router via wi-fi was lost. It catches third-party connections that were not used, and its own is gone. The router itself works, the smartphone and tablet receive Wi-Fi from it, but for some reason the laptop does not.

• Maksim

  Hello! I have this question: I have a TP-LINK TL-WR740N router. Can it distribute the Internet via WiFi without connecting to a laptop via a cable. If so, how? Thank you in advance!

• Maksim

  Everything is set up, when the router is connected with a cable, the Internet distributes perfectly, as soon as you disconnect the cable from the computer, the Internet disappears and the distribution stops.

• Oleg

  Hello! Two computers are connected via a D-Link DIR 100 router. Until recently, everything worked fine. Now there is a problem: one of the computers does not have the Internet, but there is a local network connection. speed 100 Mbit/s, packets sent are 8-10 times more than received (for example, 4365 sent, 643 received). Browsers seem to be trying to open pages, but the tabs are throwing an error. On the second computer, the Internet works fine, and the packets transmitted and received are approximately equal. Please tell me where to look for the problem? Thank you.

• Elena

  Hello. The router setup guide says:

  1. Using an Internet cable, connect the wan port of the router to the lan port of the modem.
  2. Using an Internet cable, connect your computer to one of the router ports.

  So, I have a question: in included There is only one Internet cable, and my computer is connected via a USB cable to the modem, and not via an Internet cable, as it is written in the manual, what should I do?

• Tatiana

  Good afternoon. I have a computer connected via a Wi-Fi router dlink dir 300 and home television. I want to connect home phone(the operator has such a service - Beeline), but my phone is a Panasonic KX-TG8205. Tell me what cable is needed to connect the phone to the LAN port of the router.

• Elena

  Hello, help me solve the problem. Wi-Fi router tr link. The Internet is distributed to only one of the devices. The router sees the laptop, but there is no access to it.

• Bambina

• Victor

  Good day. I came across this problem. I have a NetGear Wi-Fi router connected directly to the PC via cable. The Internet works fine on a PC, but when I connect to the router from a laptop, this problem occurs: the Internet connection periodically disappears, sometimes this happens every 5 minutes. Only reconnection helps. Please tell me what could be the problem.

• Nikolas

  Hello, knowledgeable people! I have this question, I had a DSL2740 router with wi-fi distribution, but the guys from Rostelecom came to install the fiber optic cable, and in my absence (my father is not very knowledgeable) they replaced the router too, it does not distribute wi-fi. So here’s the actual question: is there any way, by connecting them together, to still get me wi-fi? Thank you in advance for your help.

• Alexander

• tixero

  I see people understand! Please tell me. Possible to use dlna network if you use this connection method: PC => (wifi) ROUTER (cable) => TV. I’ve already tried everything, I just can’t connect the TV (everything is fine with the TV, it connects to the Internet, but it doesn’t see Dnla). What could be the reason? Maybe something needs to be changed in the router settings (B focus)?

• ZiK

  Help! So I bought a router, connected everything and then decided to install firewood, but that was not the case. The computer shows that there is no modem although it is connected! Rostelecom operators said that this is due to the fact that there are no drivers on the network card. This is true? If so, how can I find out the name for the built-in network card?

• Nastya

• Sergushok

  Hello!!! The question is the following: after reflashing the router, all the settings were followed, the problem is that one laptop was configured, asked for the key, and entered it. I tried it on the tablet and on the phone, everything was also without problems, but I can’t log in from another laptop, it says Windows was unable to connect to DIR 320NRU 2. It doesn’t even ask for a key, I try to insert a short cable from the router to this laptop, everything works, in what could be the problem, please tell me?

• Patya

• Marina

  Hello! I connected the Wi-Fi router to the laptop via a cable, configured the router, everything works. But as soon as I disconnect the cable and want to connect to the router via Wi-Fi, it takes a very long time to connect and nothing happens. I have to constantly surf the Internet via wires(((My router is TP-LINK TL-WR841N.

• Serge

  Good day, I don’t have a wireless Asus router (from my phone and laptop) connected via cable to a landline. It sends, but does not receive, in general there is no Internet at the hospital. I entered the IP address and the rest of the crap, maybe I need to remove the password?

• Sergey

  I configured the router from the disk, connected the cable that was included in the package. Everything works, WI-FI (two phones) and the computer. I connected a second computer via a cable - it didn’t have it.

• Sergey

  How to connect a second computer via a WI-FI router using a cable? When you connect the first computer with a cable, there is Internet, but when you connect the second computer with the same cable, then there is no. I downloaded the drivers today latest version. How to check properties network connection?

• Sergey

• Nur

  Please help me connect the tablet, the WIFI network is pumped up to the router, the browser on the tablet does not open the browser. What is the problem and how to solve the problem

• Dmitriy

  Dear Smart-Tronics, I have the following problem: I have a portable Wi-Fi router, but it has poor reception and is not convenient. Surfing the Internet - everything freezes. I decided to buy a large Wi-Fi router, but I don’t have one wired internet for him. Tell me if it will strengthen the connection and Wi-Fi in the house, so that you can surf the Internet perfectly, and so that nothing hangs.

• Anton

• lenyas

  Hello! Please tell me, I bought a TP-link740N router, the computer is tied to the MAC address, the router connected without problems, the MAC address was scheduled, wi-fi on the laptop and tablets, phones yes. Everything seems to work without problems. But I wanted to connect a samsyng TV through the port on the router, I can’t configure the Internet automatically, I tried it manually, still nothing, it says to check the correctness of the IP address, it seems like I’m entering everything correctly and nothing. but as I understand it, if the MAC address is linked, then how to change it on the TV. What should I do, please tell me? Thanks in advance for the answer.

• Ruslan

  Hello! There is a TP-LINK TL-WR841ND, there is a problem with the van port, I connect the Internet cable once, it worked and stopped, the van port indicator does not light up... I connect it to the van computer, the indicator works. I did the firmware... thanks in advance.

• RUFM

• Mira

  Hello! The programmer connected my Tp-Link router to my computer. The laptop sees the network, everything works well. But the computer now does not connect to the Internet. I have dom.ru. Writes: “error 678. Remote computer doesn't answer." What should I do now? Help me please!

• Andrey

  I took the laptop back from repair. I can’t connect to Wi-Fi. It says enter the network security key. Or press the button on the back of the router. How do I find out the security key? I didn’t connect the router. But I have the documents and the contract.

• Natasha

• Julia

• Max

  hello! please tell me the router is connected to the laptop and the smartphone sees it and connects, but there is still no Internet. Even when I connect the router with the laptop via cable, there is still no Internet

• Irina

  Tell me how to set up the Internet on a desktop PC using a router. The router has been installed for a long time and works with laptops, there is a need to install the Internet on a PC as well, how to do this? The apartment was completely renovated and a special internet connection was installed for desktop computer, will the Internet be supplied through this outlet through the operation of the router and how can this be installed correctly?

• serge

  I connect the network cable of the Internet provider to the internet connector wireless router DIR-300 the second cable from the network card to the LAN1 connector, I press connect, it does not connect.

• Andrey

  Good afternoon, I have a connection problem. tp-link router n600. There is a signal from the Internet cable, all the icons on the router (what is needed) are blinking, according to the settings, everything seems to be configured correctly from the disk. On the laptop, he connects to the router, but writes that there is no access to the Internet. Please help. (I apologize for the chaotic description of the problem)

• Rustam

  Hello, I can’t find the router on my computer! Maybe I’m doing something wrong. On Windows Xp everything was fine, but I reinstalled it on 7 and can’t find it.

• Anna

  TO WiFi router two laptops and a phone are connected, the network periodically disappears, either on the laptop or on the phone, not together, but on one thing, more than once a day. We reboot the router and everything works. What is the reason???

• Tamara

  Help me please! We installed another router (there were no problems with the first one), both D-Link, it somehow distributes interestingly to the laptop: Skype works, but does not open browser pages. The laptop router “saw” it, gave out its name, the signal was strong. Apparently, there is something wrong with the computer settings. But what?