How to fix KERNEL_DATA_INPAGE_ERROR blue screen errors (0x0000007A). How to fix KERNEL_DATA_INPAGE_ERROR blue screen errors (0x0000007A) Checking RAM with MemTest


With a huge number of all kinds of errors, the blue screen of death is what causes the most concern among users. Many people, completely unjustifiably, believe that the operating system is completely covered, which means that at a minimum, you should look for a disk to reinstall it. However, such a nuisance can mean completely different conflicts, so, initially, you should carefully read the information that the blue screen gives. For example, this could be error 0x0000007a. The next step is to find out the reasons for its occurrence.

Why does this error occur?

There are several reasons why stop 0x0000007a occurs:

  • The system cannot initialize the hard drive when resuming from sleep mode.
  • Drivers for various devices are damaged, have been deleted, or are simply outdated.
  • The registry of the installed operating system is damaged.
  • Viruses interrupt your computer's operation.
  • There is damage to the hard drive or RAM.
  • Important elements of the system are damaged.

How to fix? Use the instructions below.

Fixing the Trouble

If the problem 0x0000007a kernel data inpage error occurs when you try to wake your PC from hibernation, then you should calmly restart the OS, go to the official Microsoft website and download a special update, the purpose of which is to cure this disease. The update is called KB977178. It should be downloaded to your hard drive and installed, after which you should reboot the system.

If 0x0000007a Windows 7 does not disappear - how to fix it? First of all, check the status of the registry and, if errors occur, correct them. The WinThruster program or any analogue is perfect for this purpose. The next step is to search for and fight viruses, which can be performed by any installed and current antivirus program.

Of course, the usual cluttering of the drive with various temporary files, program remnants, unsuccessful uninstallations, and so on can also lead to a similar situation. Therefore, the next step is cleaning: launching the command line and entering the command “cleanmgr”.

Did not help? Then we sequentially go to the list of installed equipment and update all the drivers that we can.

A possible cause of the blue screen error 0x0000007a was some changes that the user made recently. We launch recovery tools and try to roll back the system to its working state.

  1. We check the OS for errors using the command “sfc /scannow”.
  2. We install all available updates.
  3. If the problem does not disappear, we reinstall the operating system.

The last step, if there is no solution in the described cases, is to check the hard drive and RAM status:

  1. Winchester – “chkdsk /f”.
  2. Memory - launch the Mtmtest88 application.

If the last two versions of error 0x0000007a for Windows 7 detected some conflicts, then perhaps another reinstallation will finally get rid of the blue screen. However, there is always the possibility that hardware problems are no longer compatible with full functionality, so you will have to allocate some financial resources to purchase a new hard drive or memory sticks to rid yourself of this trouble.

By the way, indirect signs of such a problem can be sound signals and a sharp reboot immediately after the screen of death appears, the inability to load the OS due to reluctance to start the equipment - a dark monitor screen and a nasty squeak from the motherboard speaker.

Good day! Today's lesson will be devoted to the next blue screen with error 0x0000007A KERNEL_DATA_INPAGE_ERROR with whom I recently had to meet face to face. Here I will tell you what you should do if you see the numbers 0x0000007A on a blue background on your screen, and how you can get rid of this problem once and for all.

Typically, this error is associated with various hard drive damage. For example, it could be poor contact between the hard drive and the controller, or it could be a bad sector that is causing this problem. It also happens that the controller may fail altogether, resulting in this error. Lack of free space is a stupid and ridiculous reason, but it can also harm our PC, so we should not discount this either.

In general, as you can see, the reasons for the appearance errors 0x0000007A there are many and in different forms, therefore, accordingly, there is no universal solution to this error either. As a rule, the final elimination of an error is achieved through tests, and the implementation and verification of various options for eliminating the error.

Therefore, in the article that you are reading now, I will not give a specific answer to the question of how to fix 0x0000007A KERNEL_DATA_INPAGE_ERROR, but I will describe only the most basic tips and recommendations that will definitely help you cope with the blue screen that appears.

A few tips on how to fix or remove the blue screen with error 0x0000007A

  • If, after a blue screen with error 0x0000007A appeared, you rebooted your computer and the system started up as if nothing had happened, then first of all, open some antivirus and;
  • Next, you can restart your computer and if you are lucky automatic verification will begin a disk that can help us with bad sectors;
  • If you are unlucky and this check does not start, then we try to start it manually using any installation disk with the corresponding system. I'll give an example of how this can be done in Windows 7:
  • The next tip would be this: check if you have enough free space on your partitions. Lack of space is usually a very rare cause of an error, but still, it is worth checking, and it will only take a few seconds;
  • Further, sometimes to get rid of error 0x0000007A, it is enough to simply clean the SATA contacts on the motherboard or HDD, or you can also try to completely replace the connected cable;
  • We try to disable memory caching in the settings;
  • Sometimes, error 0x0000007A is caused by a faulty RAM. In this case, it is often recommended to check the memory using various tests. To be honest, I can’t say anything specific about this, since in such situations I constantly check by temporarily replacing RAM strips. By the way, if you have very dusty, then remove the components and clean everything thoroughly, because even the dust that accumulates in these slots can cause various types of problems;
  • Install all recommended updates for your operating system; they sometimes install or update drivers for devices that could cause a blue screen;
  • If you connected any new devices or drives before the error appeared, then disconnect them and see if the situation changes or remains the same as before;
  • And finally, you should pay attention to the motherboard; it may be faulty or damaged. Since not many users will be able to determine this on their own, I recommend contacting a specialized service center, where a technician will properly do this for you;

The tips and recommendations that I gave were taken both from my personal experience and from the Internet. With this article, I tried to collect all the options for fixing error 0x0000007A KERNEL_DATA_INPAGE_ERROR in one place, so that you don’t have to run all over the Internet and pull information from each page one by one.

By the way, if you have anything to add, write to me in the comments or at

Sometimes various errors resulting from software or hardware failures may interfere with the stable operation of the Windows operating system. Due to the latter, for example, the so-called Blue Screen of Death (BSoD) may appear with the message Windows Kernel Data Inpage Error and error code 0x0000007A or 0x00000077.

Typically, error messages 0x00000077 and 0x0000007A occur when kernel traps occur when the operating system tries to load a page into memory from the paging file on the computer's disk, but is unable to access the data due to a software or hardware problem. This could be a damaged block in the paging file, a defect in the cable connection between the disk and the controller, a malfunction of the drive or PC RAM. The following instructions will help you clarify the nature of the error and try to eliminate it.

1. Check your computer for malware. You can do this using a free antivirus application that does not require installation.

2. Remove antivirus and other software (Acronis True Image, Daemon Tools, Adguard) from the operating system that uses low-level access to Windows components and libraries.

3. Check the file system of the C:\ drive for errors. To check, use the Check Disk system utility (chkdsk.exe) supplied with Windows.

4. Conduct diagnostics of the hard drives or SSD drives installed in the computer. This can be done using the free utilities HDDScan and R.tester. To avoid losing files and data, carefully read the instructions supplied with the programs!

5. Run diagnostics on your computer's RAM. To do this, you can use both and third-party applications, for example, MemTest86.

6. If there is a malfunction of the hard drive controller, replace the SATA communication cable with a known good one (new) or try connecting the drive to another port on the motherboard.

7. Using the Driver Manager system utility included in Windows, conduct a comprehensive diagnosis of the drivers installed in the system. About how to do this.

8. Update the BIOS, following the instructions on the website of the manufacturer of the motherboard installed in the computer.

9. Use the Windows To Go operating system, which can be installed on an external USB drive and run on any computer. Based on the stable (or unstable) operation of the mobile platform, you can determine the root of the problem and put aside its software component. How to create a USB flash drive with Windows To Go.

This error means that the requested kernel data page in the swap file cannot be read into memory. The stop code has the following parameters.

If the first parameter has one of the following values ​​0, 1 or 2, but the third parameter is 0, then the parameters will have those values.

If the first parameter is equal to 3 (and the third parameter is not equal to 0) or 4 then the remaining parameters have the following values.

Otherwise the parameters have the following definitions.

Causes

Quite often, you will be able to determine the cause of the KERNEL_DATA_INPAGE_ERROR crash by parameter 2 (error code).

The most common error codes are the following:

    0xC000009A, or STATUS_INSUFFICIENT_RESOURCES – indicates a non-paged pool memory leak;

    0xC000009C, or STATUS_DEVICE_DATA_ERROR - indicates a bad sector on the hard drive;

    0xC000009D, or STATUS_DEVICE_NOT_CONNECTED - indicates a faulty or outgoing cable, or that the controller does not see the hard drive;

    0xC000016A, or STATUS_DISK_OPERATION_FAILED – indicates a faulty sector on the hard drive;

    0xC0000185, or STATUS_IO_DEVICE_ERROR - indicates that the device's SCSI cable is faulty or that two devices are trying to use the same IRQ.

    0xC000000E, or STATUS_NO_SUCH_DEVICE - indicates faulty hardware or incorrect disk device configuration. Check the connections of the disk drives and the cables. If you are using older PATA (IDE) devices, this error code may indicate an incorrect master/slave connection type configuration.

A complete list of all execution codes is in the Ntstatus.h WDK.

The cause of the error may also be incorrect memory.

A computer virus infection can also cause this error.

Elimination

Check the disk, if the error code is 0xC000009C or 0xC000016A. To do this, run the command chkdsk /f /r. If the system does not boot, use the recovery console and use the chkdsk /r command.

Troubleshooting hardware problems. If the I/O status code is 0xC0000185 and the swap file is on a SCSI drive, check the cables connecting the drive and the motherboard. Check that the memory cards are inserted properly. If necessary, clean the contacts with an eraser. Damage to the motherboard can also cause this BSOD.

Check that you have the latest service packs installed for your system. Check your computer for viruses.


2024 gtavrl.ru.