Connect the drive from the laptop to the PC. What to do if you need to place a small drive in a computer case? Connecting a hard drive through special devices

Situation when it is required HDD connect from a laptop to a computer, usually occurs in two cases:

• must be copied from the hard drive large volume data;


• The laptop has failed, so you need to extract information from it.

In the first case, it is not necessary to disassemble the laptop and remove the hard drive; the most reasonable solution would be to use special cable, which is called a patch cord, for connecting a laptop to a computer and transferring data.
">

The only nuance of this connection is the fact that in order to transfer data between a computer and a laptop, both devices must be connected in home group through operating system settings.

To implement the second option, you cannot do without first disassembling the laptop and disconnecting the hard drive. How to do this depends primarily on the model of the laptop you are using, but you can still identify general steps.

The process of removing the hard drive from a laptop:

1. turn off the device, disconnect the power cable and remove the battery;


2. turn the laptop over and inspect the bottom; perhaps the hard drive is accessed through a special compartment, which prevents removal of the entire bottom part;


3. unscrew the screws holding the compartment, if there is one (otherwise, you need to remove all the fasteners holding the bottom of the structure);


4. Pull the hard drive out of the connector in the exact opposite direction and pull it out.

Connecting the hard drive directly to the computer motherboard

This is the first option for connecting a laptop hard drive to a desktop computer. To implement it you will need to do the following:

1. turn off the computer and disconnect the power cable from the electrical outlet;


2. remove the side wall system unit;


3. Using a SATA cable, connect the hard drive to the system board;


4. connect the cable from the power supply to the hard drive;


5. securely fix the hard drive, screw on the cover and turn on the computer.

After connecting in this way, the hard drive will appear in the system as a local disk.

If you do not have spare SATA cables to connect your hard drive, you can temporarily remove similar ones from your drive.

If you want to install a laptop hard drive into the system unit and use it constantly, you need to secure the hard drive using special slides.

Slides that allow you to secure a 2.5-inch hard drive into a 3.5-inch system unit bay.

Connecting a hard drive through special devices

This method is simpler compared to the option outlined above, since it does not require disassembling a desktop computer.

Using a SATA to USB adapter

There are many varieties of such adapters. Typically, these devices have several connectors that can be used to connect both SATA and IDE drives.

Using a hard drive enclosure

On sale you can find a special device that allows you to turn any laptop hard drive into a full-fledged external hard drive. Usually such a device is called a box (from the English word Box, which means box). Boxing is a container small size, into which the hard drive is inserted. The box is connected to the computer via a USB connector.

When purchasing a box, you should take into account the physical size of the hard drive that you want to connect to it. There are two types of boxes:

• for 2.5-inch hard drives;


• for 3.5-inch hard drives.

Practice shows that the likelihood of needing to connect the hard drive of one of computer devices to a laptop or the implementation of the opposite reconnection scenario is prohibitively large. A precedent for this could be a “digital disaster” that suddenly or naturally appears... The methods described in the article are intended to help the “puzzled user” in solving the common problem of how to connect a laptop’s hard drive to a laptop. Of course, valuable material, consisting of extremely effective recommendations, will affect all options for interface interaction of various types of information storage devices in order to obtain full access to the data on them.

Discord in the single purpose of the hard drive: a threat to a healthy psyche

Wow, how confusing everything is! are equipped with one type of storage device, laptops and a separate type of computing device with a NET prefix are equipped with another. However, all these devices have a single universal ability - storing and processing information. This means that “interface differences” when deciding how to connect a hard drive from a computer to a laptop can be circumvented. And also to avoid the state of slight confusion that often arises (for a “victim of technological circumstances”), when the hard drive of a failed PC contains extremely necessary data that is needed “right now.” Relax, dear reader, there is a way out! Take a breath... and not even in a single version!

to the laptop: instructions for SATA devices

Let's take a closer look at this situation: there is a working laptop to which you need to connect the HDD from the PC.

1. First of all, you need to purchase a special SATA-eSATA adapter, when choosing which you must be guided technical characteristics receiver device. In our case, this is the presence of a “favorable” eSATA connector on the laptop.
2. Most modern portable configurations have this interface. Which ultimately will become a kind of answer to the question of how to connect a hard drive to a computer or laptop.

If your laptop has this type of interface, then further process initialization takes place almost instantly. The operating system will literally immediately identify the connected device as an external drive. Moreover, the operating speed when organizing this kind of synchronization process is incredibly high, up to 6 Gbit/sec. Agree, with such parameters you can quite comfortably interact with data of any (within reasonable limits) volume.

Guide for IDE hard drives: universal USB port

How to connect a hard drive to a computer (laptop) if the drive has a somewhat outdated interface and the laptop only has a universal USB connector? Undoubtedly, it is a rather “complex symbiosis”. However, as mentioned earlier, there is a way out!

1. Everything is resolved using a special adapter that connects to the laptop using a USB cable.
2. The device's IDE input connector allows you to connect a PC hard drive, and a separately routed cable is used as a power supply.

As a rule, such devices are often universally used gadgets. Since they often provide two types of connections - SATA-USB and IDE-USB - using one controller adapter.

“Brotherly understanding”: two cords decide everything!

You will not have a question about how to connect a laptop hard drive to a laptop if your laptop has the previously mentioned serial interface, and your “reconnect” arsenal has an eSATA to SATA adapter (7+15 pin). Otherwise, you should pay a visit to your nearest electronics store and buy an inexpensive “pocket” for an external HDD.

This option is most suitable for optimal solution voiced difficulty. Since the owner of such an HDD container may well use the purchased device (in the future) for its intended purpose - as an additional external storage information.

By the way, the “HDD pocket” can be connected not only via the eSATA interface, but also via a universally used USB port. Which will make the situation incredibly easier when you need to connect a 2.5 ̎ drive laptop computer to a desktop PC. Do you see benefits from such an acquisition?

Climactic finale: extreme ascent of information at random

When deciding how to connect a laptop hard drive to a laptop, if the situation requires quick access to data on external hard drive and provided that there is no necessary adapter, but there is a flash drive and access to the Internet:

1. Download Live USB distribution.
2. After you create a bootable Flash drive, turn off and unplug your laptop.
3. Remove the device's battery.
4. On the back of the laptop, find text designation HDD, which is a kind of landmark that indicates the location of the installed hard drive laptop.
5. Unscrew the protective cover and carefully remove the HDD.
6. In the freed space, install a hard drive on which the information you need (urgently!) is stored.
7. After you boot from the flash drive, you can view the “secret data”.

This is how you can get a practical answer on how to connect a laptop hard drive to a laptop. Basic techniques for gaining access to stored information external HDD information has been reviewed in full. Good luck to you and all the best!

There are two types of hard drives - internal and external (like a USB flash drive). Connecting hard disks via the IDE interface, which is used on all older models hard drives. Or – SATA, which has a much narrower connector and cable width.

When connecting a hard drive to a laptop, remember that not all modern laptops have external connectors for of this connection. Then the connection can be made using the USB interface. But for these purposes you need a specialized SATA/IDE to USB input adapter. This adapter can be found complete with a hard drive power supply. The unit is required due to lack of power from the USB interface. When connecting a hard drive through an adapter, you need to be extremely careful not to inadvertently damage the hard drive when it is lying next to the laptop. Manufacturers computer office equipment They produce special pockets for hard drives with the necessary built-in adapters. This pocket serves as a kind of protective cover for HDD. The container's connectors should be connected to the hard drive by installing the HDD in the container's pocket. Then to USB input laptop, connect the connecting cable and, if necessary, external power to the container.

The hard drive is usually connected when the laptop is turned off. After switching on laptop hard The disk will automatically begin to appear in the explorer of the laptop operating system. Otherwise, you need to install drivers from the included disk or downloaded from the container manufacturer’s website.

This way connecting hard drive is no different from connecting any other USB storage device. However, there is a strict rule when doing this. To avoid irreversible HDD damage, you cannot turn off the power while the disk is running. Also need to use safe removal devices after working with hard drive, before disconnecting it from the laptop.

If you often have to transfer information from your computer’s hard drive to a laptop, or vice versa, then you should purchase a special portable HDD. This kind hard drive has a USB cable for connection, is protected from external damage by a durable case and is used specifically as a portable drive.

The hard drive serves as the main storage medium user files and programs, including documents, videos and music. There are many reasons why owners might want to connect a PC hard drive to a laptop. For example, to retrieve data after an operating system crash or to transfer data to new laptop.

The most in an accessible way connecting a hard drive to a laptop is to use an adapter or docking station.

Such a docking station costs about $30-40. For example, Anker USB 3.0. Its only problem is that it most likely does not support IDE interfaces and SATA. If you want to connect a hard IDE drive or SATA, it is best to use special adapters.

Sabrent USB-SATA/IDE adapter

An example of an adapter between USB and SATA is the “Sabrent USB-SATA/IDE adapter”, which allows you to mount hard drives as a portable HDD or flash drive.

Historically, these adapters were quite complex, but advances in technology have made them much simpler and smaller. Modern USB/SATA adapters provide reliable functionality for affordable prices. The model we are considering is Sabrent USB 3.0 to SATA/IDE adapter. This is a reliable, fast and at the same time powerful adapter. It has a built-in Molex transformer. This makes it possible to include disks with any interfaces. You can purchase most adapters at almost any store. computer equipment. They provide communication between the hard drive and the computer, but will not be able to support its power supply (especially for old HDDs desktop computers). To work with such adapters, you need power through the computer's old power supply, which is not always possible.

Connecting the adapter

If you already have the hardware, then all you need to do is connect the appropriate side of the adapter (3.5 IDE, 2.5 IDE, or SATA) to the hard drive.

Note: Make sure the HDD jumpers are set to “Master” (especially if the drive is old; modern SATA drives jumpers are rarely used).

Connect the adapter to USB port on your computer and turn on the power via the MOLEX connector on the adapter. Then turn the switch on the cable to power the drive. This is what a properly connected IDE drive looks like

Once power is connected, the drive will turn on and should appear in Windows Explorer as a removable or local disk. Here's what a detected drive looks like in Windows Explorer.

Now you can see all the old data that can be copied to the main media.

Note: When opening, copying or deleting folders on old hard disks with previously installed Windows OS, you may encounter access problems. This error occurs because file permissions were managed by the previous operating system. In most cases, it is enough to click the “Continue” button in the pop-up window.

If your drive is not detected by the operating system, but you have connected everything correctly, then the reasons may be as follows:

1) Jumpers are set to “Slave” mode. You must set the jumpers correctly.

2) File system drive is not supported by the OS. Most often, this problem occurs if the hard drive was formatted in Linux OS. In this case, you must boot into Linux to access the data.

3) The disk is damaged. In this case, it will be almost impossible to extract the data.

The desktop computer was outdated or out of order, but the hard drive with numerous files accumulated over many years, fortunately for its owner, remained working. There is a laptop available, which means there is no point in resorting to upgrading an old computer and “bringing it back to life.” Let's connect the hard drive to the laptop, which is on computer language and there is internal hard HDD drive, and we will transfer all the necessary information from it.

Visit a specialized computer equipment store, where, in consultation with the manager, decide on the choice of an adapter device that will help connect the hard drive to the laptop. If you do not have extra funds, then use the Internet to find where to buy an adapter in your region. Act economically and opt for a fairly cheap multifunctional adapter - a “SATA” cable in other words. When purchasing, make sure that the kit includes: two cords (power adapter that connects to electrical network And USB cable), disk with software, which will be needed if an old operating system is installed on the laptop, instructions and the adapter itself - such a nice little thing with connectors. For long-term use of a hard drive, purchase a modern USB 3.0 IDE to SATA adapter cable, which will easily allow you to connect the hard drive to a laptop in a matter of seconds. The kit also includes all the necessary cords and user instructions.

Connect the purchased adapter to the laptop via the contact USB interface and don’t even think about opening the case of your portable device. Also connect the hard drive to a device that is equipped with a special connector. If you need to install drivers, be sure to use the disk included in the kit or update the driver via the Internet. Now your hard drive will work like a regular flash drive. Unlike hard drives 3.5 inches wide and higher, a 2.5-inch hard drive with optimized capacity attached to the adapter does not require additional connection to the electrical network using the power supply included in the product assembly. You will find out the HDD parameters when you pick it up. The sticker contains all the necessary characteristics.

Take the choice of adapter seriously if you want to use old hard disk as external storage. Don't forget to take the hard drive with you when you go to a computer store to buy an adapter. The seller may suggest that you test the adapter in operation right there by selecting the appropriate cable.