Connecting a laptop to the dir 320 router. Setting up a network card

All tips

If you purchased a new router or moved to a new place of residence with old equipment, then most likely you will need to configure the d link dir 300 Rostelecom router. This process is not as complicated as it seems at first glance. In this article we will prove this and consider all the stages of this procedure, as well as setting up the d link dir 320 Rostelecom router.

Preparing the router

Setting up a router dir 300 Rostelecom - old firmware

New firmware and work with the dir 320 model

Enabling WiFi protection

Conclusion

cost of Interactive TV from Rostelecom.

You can read how to connect Interactive TV through a router here.

After successfully logging into the main interface, the router will most likely prompt you to change the standard password to your own. We enter the invented combination of characters in two fields, confirm and go through authorization again, but with new data. If everything is done correctly, you will see the main menu in the form of blue “buttons” of a fairly large size.

To start setting up the network, perform the following operations:

click on the first (lower left) button of the second line “Configure manually”;

In the top text menu, select “Network”;

open an existing “WAN” connection;

Scroll down the page and click “Delete” in the lower right corner;

wait until the page refreshes, the “Add” button appears on the right, click on it;

on the settings page that opens, specify the type of Internet connection – PPPoE;
we do not touch the port;

choose any name (this will be the name of your connection in “Network Connections” on your computer);

Below we indicate the login from the agreement with Rostelecom, as well as the password;

save the changes made, then click “Save” again in the center of the page.

At this stage, we put aside the Rostelecom agreement and check the settings of the dir 300 router - go to any page on the Internet. It should open without problems. All that remains is to configure the wireless network. For this:

open the WiFi menu item (located next to “Network”);

in the SSID field, enter any name for your network and move on;
to set a password, save the changes and select from the available WPA2-PSK options;

Enter the password you created and save again.

That's all, the connection and wireless network are ready to go.

How to disable the Gudok service.

You can read about the transfer of subscribers of the mobile operator Rostelecom to Tele-2 here.

From this article you learned how to set up a dir 320 router for Rostelecom, as well as its previous model, and these instructions should work in most cases. If you have such a typical problem as the web interface being unavailable via IP (that is, the browser does not open the authorization page after entering the combination 192.168.0.1), then again go to the Internet protocol properties (where we set automatic IP/DNS acquisition) and switch network for working with static data. In the fields that have become active, indicate:

168.0.12;

leave unchanged (should fill in automatically);

168.0.1;

DNS data from the contract;

also stated in the contract.

After applying these changes, the login page should become available. If you still have questions, watch this video:

And that's all. Tell us about your experience connecting to the Internet. Any questions in the comments are welcome!

On many devices, setup is quite easy if you know all its nuances. To make a connection, you need to outline a plan for the sequence of operations to configure the main equipment to work on the global network together with the device and implement the setup of the D-Link Dir 320 router.

Work order

The instructions we will follow are as follows:

Setting up a network card in relation to different operating systems using the example of Windows XP and G7.
Troubleshooting problems when turning on and operating the modem.
Replacing an old chip or flashing a new one for proper operation of the D-Link Dir Wi-Fi router.
Basic network settings for different operators.
Setting up a Wi-Fi network.

Inexperienced users, when connecting the device, think that it will automatically tune to the desired provider and they will be connected to the global network. In fact, it is easier for them to call an employee of a company that provides such services. And who does not want to spend personal savings, we advise you to read the instructions for initializing the router located below.

Setting up a network card

Before installing the router, it is necessary for the computer to recognize the network card, then you need to set the IP address to the “automatic” position. This is necessary to synchronize the settings of your PC with the D-Link device, which has this specified in the factory settings.

We proceed according to the following scheme:

Click on “Start” and enter it.
Click on “Control Panel”.
We find the picture with the inscription “Network connections” and enter.
In the window that appears, select the picture next to which there is the inscription “Local Network Connection”.
Then right-click on it and find the “Properties” item.
Having entered it, put a tick on the inscription “Protocol (TCP/IP)” and click on “Properties”.
At the end, put the dots on “Automatic” and click “OK”.

The scheme is as follows:

Click on “Start”.
In the search engine (the line right above the “Start” button) enter the word “Network”.
In the window that appears, look for the inscription about the local network and click 2 times.
Then, by clicking on “Properties”, look for “Protocol version 4” and double-click.
Select “Automatic” and click on “OK”.

How to set up a D-Link Dir 320 NRU router without problems

After setting up the card on your PC, you need to make sure the IP address is correct.

Return to the item labeled “Local Area” and in the window that opens after double-clicking, select:

"More details" on Win XP.
"Information on Win

The IP address will be something like 192. 168. 0. XXX

If the address is not received, then the number will be 169.ХХХ. XXX. XXX.

XXX – any number (for example, 101, 204, 3) not more than 255.

To insert the correct addresses you will need to return:

in Protocol (TCP/IP) for Win XP.
Protocol 4 (TCP/IP v4) for Win

The detailed setup should look like this

At the end, click “OK”.

Replacing an old microcircuit or flashing a new one

We will explain step by step how to flash the router firmware using a PC, in other words, how to reset the original parameters.

First download the current version of your device from the pages indicated in the figure:

To perform a reset and create the necessary settings for some models, you need to disconnect the Internet cable from the PC. So, check both options.

How to login - Link 320:

Connect your router to your PC and log into your browser.
You must enter the following in the address line: 192. 160. 1 – then press Enter and log in.
Enter the word admin in the “Login” field, and then Next or OK.

If login fails, try another option:

Enter the word admin in the “Login” cell and in the “Password” column.
In older D-Link devices, the firmware version looks like this:

To flash:

go to “Maintenance”;
then on the left in the “firmware update” menu;
then click on “Browse”;
find a new firmware version;
At the end, click “apply” and wait for the result.

New devices may have three different designs:

First option.

We look for the word “System” in the left menu and click on the button. Next, in “Software Update”, turn on the “Browse” scanner and select the required file.

Second option

“Configure manually” – “System”, go to the “Software update” item and select the file.

Third option

“Advanced settings” – “System”, then click forward and click on “Software update”.

After all the switches, you need to click on the apply button (“Update”).
Next you will need to wait about 7 minutes. This is necessary to complete the operation completely.
As soon as the installation occurs again, you must enter 192. 168. 0. 1 into the browser address bar and log in.

Connecting to providers and Wi-Fi

Beeline Communications

First, go to “Advanced settings” - “Network” - “WAN” - “Add”.

In the connection columns “Type” and “Name” – click L2TP + Dean. IP. in the first and any inscription in the second.
In the “User” (Name) section and in the “Password” column, enter the information received from the technicians who connected the equipment.
In the “MZT Address” field, enter – tp.internet.beeline.ru, then “Save” in one window and “Save” in another.

The setup of the D-link Dir 320 Beeline router is complete.

Communication Rostelecom

The primary actions are the same as in connection with Beeline. Further:

In the “Type” column, click PPPoE.
In the “PPP” field – in the “User” (Name) item and in the “Password” column – enter information from Rostelecom employees.
Click “Save”.

Setting up a Wi-Fi network

It also starts with “Advanced settings”, but then click “Wi Fi” - “General” - “SSID”, enter any inscription - the name of your personal network and click on “Change”.

Next, go to “Security” – “Network Authentication:” – “WPA-PSK2”, enter 8 or more characters in the “Encryption Key” and click “Change”.

Congratulations. You did everything right.

Visual instructions for setting up Dir 320 (video)

Useful video with router settings:

You can configure the router yourself. By doing this, you will save money, learn how to set up a device, and, perhaps, start your own business connecting users to the Beeline and Rostelecom networks.

D-Link DIR-320 is a router that allows you to organize a wireless network to connect to the Internet. The built-in firewall protects users of the entire WiFi network. The router is equipped with additional security features (MAC filter) and encryption (WEP and WPS), which minimizes unauthorized access to the access point.

Any wireless network needs protection from connection by unauthorized persons. There are several ways to restrict access to the router. The simplest of them is to set a password for WiFi. To do this, you need to connect the router to your computer, configure it, and then proceed to set a password. As an example, let's try to set a password on the WiFi D-Link DIR-320.

Quick navigation through the article

Setting a password

A password allows you to protect your wireless network from unwanted connections. To set a password, you need to connect the router to your computer (via a special cable that comes with the kit), configure it and perform the following steps:

Go to the IP address “http://192.168.0.1” (you can use the standard Internet Explorer browser, however, depending on the router firmware, the IP for connecting to the control panel may be different - http://192.168.1.1);
In the “Username” field enter “admin”;
In the “Password” line, write “admin” or leave it blank (depending on the router firmware version);
Click the “Login” button;
In the window that appears, on the left side, select the “WiFi” -> “General Settings” section;
Check the box “Enable wireless connection”;
Go to the “WiFi” -> “Security Settings” section;
In the “Encryption Key” field, create and enter a new password (it is best to set the WPA2 encryption mode);
Click the “Change” button;
In the upper right corner of the page, select “System” -> “Save and Reboot”.

In order for a password to become reliable protection, you must adhere to the basic rules for choosing it:

The password must consist of at least 8 characters (letters of different sizes, numbers, symbols);
You cannot use first names, surnames, or animal names that may be known to unauthorized persons;
It is not recommended to use dates of births, weddings, etc.;
It is better not to use simple words and sets of numbers;
It is advisable to change your password periodically.

In order to connect your computer to the Internet, the user needs to configure his router and himself. Only after this will it be possible to easily open various electronic pages of websites and download the necessary information.

Connecting a router

Setting up and connecting the D-LINK DIR-320 router begins with checking the functioning of important network nodes on the router itself and the computer.

To get started, you need to do the following:

If everything is done correctly, then you can start setting up the router itself and the connection.

Login to settings via web management

Before you start setting up D LINK DIR 320, you need to check the operation of network devices.

To do this, you need to perform the following procedure:

These steps are necessary to prepare the automatic configuration of the d-ink dir 320 wifi router and local network.

After setting up a local connection, you need to launch the disk included with the router. It is necessary to create a local connection to the Internet and configure the router itself. This is done according to the prompts that pop up in the installation window.

Particular attention should be paid when choosing the connection technology parameter - pppoe or l2tp. You should choose a connection format in accordance with the parameters specified in the Internet connection agreement.

The next step is configuration via the web interface. To do this, you need to type the IP address 192.168.0.1 in your Internet browser.

The login and password are in the instructions, which the system will prompt you to change after logging in.

After changing the login and password, an interface will appear on the screen in which all connection parameters will be indicated, including all possible settings parameters based on the provider’s technology.

Firmware update

The standard router kit includes a disk with software necessary for the correct operation of the network device, but this does not guarantee the uninterrupted and correct functioning of the D-LINK DIR-320.

How do I configure and install the latest version of the required drivers?

Software updates for the D-LINK DIR-320 router can only be done using the home Internet page – 192.168.0.1. This procedure should be carried out immediately after installing the basic software from the disk by following the link “ftp://dlink.ru/pub/Router/DIR-320_NRU/Firmware/”. Download and save the file to your desktop.

Thus, the path to the file is set, on the basis of which the router software will be updated. When carrying out this operation, you cannot turn off and restart the computer before it is completed, otherwise a failure may occur and you will have to start installation and configuration from the very beginning.

When the update is complete, the DIR-320 will reboot.

Setting up the D-LINK DIR-320 router from providers

The providers themselves often take advantage of the information weakness of users, most of whom are simply afraid to get into the hardware and figure it out on their own. In this regard, it is always possible to call an appropriate specialist to your home to carry out the appropriate work on setting up the Internet.

For example, setting up a D-LINK DIR-320 router from Rostelecom can be ordered by dialing the technical support number. The operator will listen to all your problems and offer a convenient time to call a company specialist at your home.

In fact, all these steps are simple, and you can do them yourself without additional expenses.

To do this, you must adhere to the following sequence:

This sequence of setting up an Internet connection is applicable to the Windows 7 and 8 operating systems.

Setting up for Rostelecom

To configure the D-Link DIR-320 router on the Rostelecom provider network, the user must go to the router’s home page (192.168.0.1) and perform the following steps:

Setting up for Beeline

Setting up the D-LINK DIR-320 router for the Beeline provider differs from Rostelecom, because they use the connection type "l2tp".

So the user's actions should look like this:

If everything is done correctly, the user will be able to freely use the Internet.

Setting up for MTS

Connection to the Internet from the MTS provider uses pppoe technology.

Therefore, setting up the D-Link dir 320 router will proceed as follows:

checking the operation of the network device;
go to the home page of the router in the Internet browser 192.168.0.1;
install drivers;
update drivers;
go to the “network” tab and select the “connections” line;
in the window that opens, select the “add” option;
connection type is set to “pppoe”;
check the “allow” box;
in the line “physical interface” set the parameter “port5”;
in the user name and password lines we enter the corresponding data from the agreement with the provider;
in the “NAT” and “firewall” lines, check the boxes;
save the parameters and configuration.

Video: Setting up a D-Link dir router

Setting up Megafon

Internet from Megafon is mainly provided using 3G technology. Therefore, all settings are set manually:

go to the router page 192.18.0.1;
select the “Internet installation” column;
in the updated window at the bottom, select the option “set up an Internet connection manually”;
in the window that opens, select the connection type “3 GUSB adapter”;
in the fields of login, password and dial number in accordance with the parameters issued by the provider under the contract;
save the parameters.

Wireless connection

Network operation via the wi-fi module of the DIR-320 router is very simple and convenient. To set up a wireless connection, just follow the prompts during the initial installation of the driver on the router. If a corresponding message appears during the installation process, you should set the recommended parameters according to the prompts.

The main attention should be paid to the settings of the network card on the computer to support a wi-fi connection. In this case, you need to go to the control panel, and in it select the network and sharing center. Next, enter the option to change adapter properties and check the operating status of the wi-fi module. If everything works, then the connection to the Internet will occur immediately and without delay.

Wi-Fi connection settings in Windows 7

If the connection to the Internet does not occur automatically, and this only happens when using older versions of D-LINK DIR-320(b1) or the windowsxp operating system, then manual configuration will be required. To do this, you need to go into the settings of the wireless connection adapter and manually set the IP and DNS address. In this case, the IP address will correspond to the router address, and the submask (dns) will be 255.255.255.0.

Next, the user must create a new connection without changing the parameters. You only enter your login and password information to connect to the Internet, and a shortcut is created on the desktop, when opened, a direct connection occurs.

Thus, in order to fully configure your D-LINK DIR-320 router, you need to:

carefully read the instructions for the router;
check the operation of the network card and local network settings on the computer;
install drivers and configure the connection according to the prompts during the installation process;
update drivers to the latest version.

Experienced users can easily cope with such a task, but for beginners it will be difficult. But if they configure their router strictly in accordance with the indicated order, then the result will not be long in coming.