HP laptop select boot device. How to enter the BOOT menu on a laptop and computer
Boot Menu– this is a menu that allows you to select the device that the system will process first. This function is actively used to replace operating systems and to carry out diagnostics, such as random access memory with MemTest.
This function is extremely convenient, as it is intended for a one-time launch of the equipment as the main carrier. This same function is needed when Windows installation, since it does not require a change in priorities.
After completing the steps required to enter the menu, all devices that are connected to the menu will be displayed. this moment time on the computer, and with which the program is potentially likely to run.
Unfortunately, there is no single denominator in the matter of entering the described menu, since there is no strict standard in this industry yet. However, there is a dependency on the manufacturer and the steps required to boot launch Menu, which will be discussed in detail in the article.
General information on entering the Boot Menu
Boot Menu is used to specify which device the program should be launched from. Of course, the BIOS already has such functionality, but for one-time use, for example a program, it is better to use the boot menu.
An interesting question is how to call up the boot menu on the motherboard because there are no standards in this regard. Each manufacturer uses various options. Most often, a hint appears on how to go to the section. In general, the F8, F9, F11, F12 and Esc buttons are used.
For start desired menu You should press the key corresponding to your brand of motherboard during system startup. Often several of the above buttons are used. You can get more accurate information by going to the section that corresponds to your computer manufacturer.
There are also slight differences in launching the necessary menu in all-in-one PCs and laptops that have pre-installed Windows 8 and above.
How to access the boot menu on a netbook? – The situation is complicated by the fact that laptop computers may not use complete shutdown, instead of it - hibernation. This option is quite justified, as it returns the PC to a working state faster, but is not suitable for entering the menu. You only need to completely turn off the netbook by holding Shift and clicking on “Shutdown”. If this does not help, then you need to configure the “Power Options” section.
Launching Boot Menu in Windows 8, 8.1, 10
The whole point is that personal computers in this configuration, hibernation mode is most often used instead normal shutdown. Often this has a positive effect on the system boot time, and processes launched in the last session are restored, but in in this case us this method is not suitable, use one of the following options:
1.Restart the computer using the appropriate option in the menu, you don’t need to just turn it off with the button and turn it on again, for the reason just described;
2. At the moment when you press the “Power off” button, hold Shift key, thanks to this procedure the PC will turn off completely, then press the desired key at the moment of launch;
3.You may need to disable quick start.
- Open the Start menu;
- Go to “Control Panel”;
- Select the tile named "Power";
- Follow the link "Actions" power buttons»;
- Disable the "Quick Launch" item.
After completing these steps, when the system starts, you will need to press the required key, usually Esc, F8, F9, F11, F12. More detailed information according to your motherboard model is indicated below in the appropriate paragraph.
Login to Boot Menu for Acer manufacturer
This manufacturer uses the same key to enter the Boot Menu on all versions of computers, all-in-one computers and laptops, this button is F12. Distinctive feature is only an item in the BIOS or UEFI that includes the necessary handler, that is, nothing will happen until you enable this function, sometimes it works by default, for this:
1.Go to BIOS, for this boot press F2 or Del;
2.Find the “F12 Boot Menu” item;
3.You need to replace the value with “Enabled”;
4.Restart your computer.
After completing these steps, the boot menu should become available by pressing F12.
Boot Menu for Asus
For the vast majority of computers at the base, which is located this platform To launch the Boot Menu you need to press F8, but with laptops everything is a little more complicated, there is some division here.
For most Asus laptops, the Esc button is used, but this is more likely for more or less modern PCs, and for models that start with K and most with X, F8 can be used.
Logging into the Boot Menu on Lenovo laptops
It’s quite easy to go to the menu of interest thanks to the F12 key, it is used in all models. This situation also applies to monoblocks from the same manufacturer. Distinctive feature is special button, located on the body, next to the standard switch, there is usually a circular arrow drawn on it, by clicking on it you can get to the menu special options system startup.
Information on other manufacturers
For most manufacturers, there is no point in describing instructions for switching to the Boot Menu, since the only difference is required key, and everything else works according to standard scheme, So:
- Laptops Dell, Toshiba and motherboards Gigabyte boards– F12;
- Samsung laptops and motherboards Intel boards– Esc;
- HP laptops – F9;
- AsRock and Maternal MSI boards– F
This should be enough to launch the Boot Menu for any computer configuration; if you have a little-known manufacturer, you should use the instructions, which should be presented on the manufacturer’s website.
If you still have questions on the topic “How to enter the Boot Menu on a laptop and computer?”, you can ask them in the comments
if(function_exists("the_ratings")) ( the_ratings(); ) ?>
Good day everyone.
When installing Windows (for example), very often you need to select bootable media, different hard drive. This can be done in two ways:
1) Go into the BIOS and change the boot queue (i.e. put the flash drive in the boot queue before the HDD - this way the PC will first check the flash drive for boot records, and only then the hard drive);
2) Call the Boot Menu and select the specific media to boot into this moment. In my opinion, this option is even better than the first: faster and no need to go back and forth into the BIOS to change the boot queue.
To enter the BIOS (call Boot Menu) in most cases the following keys are used: F2, Del, Esc, F12 (depending on the device manufacturer). The button must be pressed immediately after turning on the computer (you can do it several times so as not to miss the right moment.
By the way, if you look closely at the first screen, which is visible immediately after turning on the computer, then there is often a button written on it to enter required settings(call menu). An example in the screenshot below.
Rice. 1. Dual Bios. DEL button - enter BIOS settings, F12 button - Calls Boot Menu.
Table No. 1: hot keys for computers
To use the table, you need to know what motherboard you have and the BIOS version. There are several ways to find out, here are the fastest:
Simple free program, which will tell you quite a lot about your hardware. For example, you can find out information about: processor (CPU), RAM (Ram), motherboard (Motherboard), video card (Graphics), HDD drives, SSD (Storage), etc. In addition, you can find out and control the temperature online main components: hard drive, video card, processor.
A screenshot of the operation of this utility is shown in Fig. 2.
Rice. 2. Speccy - obtaining information about the motherboard
Table No. 1
| Motherboard | BIOS version | Hotkey | Which menu will be open |
|---|---|---|---|
| Acer | Del | Enter Setup | |
| F12 | Boot Menu | ||
| ASRock | AMI | F2 or DEL | run Setup |
| F6 | Instant Flash | ||
| F11 | Boot Menu | ||
| TAB | switch Screen | ||
| Asus | Phoenix Award | DEL | BIOS Setup |
| TAB | Display BIOS POST Message | ||
| F8 | Boot Menu | ||
| Alt+F2 | Asus EZ Flash 2 | ||
| F4 | Asus Core Unlocker | ||
| BioStar | Phoenix Award | F8 | Enable System Configuration |
| F9 | Select Booting Device after POST | ||
| DEL | Enter SETUP | ||
| ChainTech | Award | DEL | Enter SETUP |
| ALT+F2 | Enter AWDFLASH | ||
| ECS (Elite Group) | AMI | DEL | Enter SETUP |
| F11 | BBS POPUP | ||
| FoxConn (WinFast) | TAB | POST Screen | |
| DEL | SETUP | ||
| ESC | Boot Menu | ||
| GigaByte | Award | ESC | Skip memory test |
| DEL | Enter SETUP/Q-Flash | ||
| F9 | Xpress Recovery Xpress Recovery 2 | ||
| F12 | Boot Menu | ||
| Intel | AMI | F2 | Enter SETUP |
Table No. 2: hot keys (Bios/Boot Menu, etc.) for laptops
Note: on modern laptops The key combination works the same way in Windows: hold down the SHIFT button + select the restart button with the mouse.
The Boot Menu is a small window in which, using the mouse (arrow keys on the keyboard), you can select the device from which to boot. An example of such a menu is shown in Fig. 3.
Depending on the manufacturer of your device, the menu may differ slightly, but the principle of operation is the same everywhere.
Table No. 2
| Laptop manufacturer | BIOS version | Hotkey | Function/menu call |
|---|---|---|---|
| Acer | Phoenix | F2 | Enter Setup |
| F12 | Boot Menu (Change Boot Device,Multi Boot Selection Menu) | ||
| Alt+F10 | D2D Recovery (disk-to-disk system recovery) | ||
| Asus | AMI | F2 | Enter Setup |
| ESC | Popup Menu | ||
| F4 | Easy Flash | ||
| Phoenix Award | DEL | BIOS Setup | |
| F8 | Boot Menu | ||
| Benq | Phoenix | F2 | BIOS Setup |
| Dell | Phoenix,Aptio | F2 | Setup |
| F12 | Boot Menu | ||
| eMachines (Acer) | Phoenix | F12 | Boot Menu |
| Fujitsu Siemens | AMI | F2 | BIOS Setup |
| F12 | Boot Menu | ||
| Gateway (Acer) | Phoenix | Click mouse or Enter | Menu |
| F2 | BIOS Settings | ||
| F10 | Boot Menu | ||
| F12 | PXE Boot | ||
| HP (Hewlett-Packard)/Compaq | Insyde | ESC | Startup Menu |
| F1 | System Information | ||
| F2 | System Diagnostics | ||
| F9 | Boot Device Options | ||
| F10 | BIOS Setup | ||
| F11 | System Recovery | ||
| Enter | Continue Startup | ||
| Next | F1 | Calling Boot Menu | |
| F2 | BIOS setup | ||
| Lenovo (IBM) | Phoenix SecureCore Tiano | F2 | Setup |
| F12 | MultiBoot Menu | ||
| MSI (Micro Star) | *** | DEL | Setup |
| F11 | Boot Menu | ||
| TAB | Show POST screen | ||
| F3 | Recovery | ||
| Packard Bell(Acer) | Phoenix | F2 | Setup |
| F12 | Boot Menu | ||
| Toshiba | Phoenix | Esc,F1,F2 | Enter Setup |
| Toshiba Satellite A300 | F12 | Bios |
Table No. 3: recovery from a hidden partition (for laptops)
Most modern laptops have a built-in special hidden partition with the ability to restore the Windows OS using a “pair” of keys (there is no need to prepare a bootable USB flash drive, download ISO images with Windows, etc.).
As a rule, to launch the recovery function, after turning on the laptop, just press one key (F9, for example, on Asus laptops). Next, a window will appear in which you need to follow the instructions of the recovery wizard.
Note: when restoring information, system disk"C:\" is often formatted and all information from it is deleted. Make a copy of important data from it in advance.
Rice. 4. ACER laptop- service recovery utility
Table No. 3
| Laptop manufacturer | Button combination | Note |
|---|---|---|
| Acer | Alt+F10 | First you need to log in Laptop Bios, and enable the D2D Recovery function. The default password in the recovery system is 000000 or AIM1R8. |
| Asus | F9 | |
| Dell Inspiron | Ctrl+F11 | |
| Fujitsu Siemens | F8 | |
| HP | F10, F11 | |
| LG | F11 | |
| Lenovo ThinkPad | F11 | |
| MSI | F3 | |
| Packard Bell | F10 | |
| RoverBook | Alt | |
| Samsung | F4 | |
| Sony VAIO | F10 | |
| Toshiba | F8, F11 |
PS
The tables will be updated (over time). For additions on the topic of the article - thank you very much in advance. Good luck to all!
What is boot menu
Probably everyone knows that in order to boot from a disk drive or flash drive you need to set the order of devices to boot in the BIOS. For example, to install Windows XP from a disk onto a computer, you first need to boot from this very disk. To do this, you need to set the disk drive as the first boot device in the BIOS.
However, you don’t have to go into the BIOS and change nothing there. All you need to do is immediately after turning on the computer, press the boot menu key and in the list of devices that appears, select the one from which to boot. Selecting a boot device in the boot menu has no effect on BIOS settings. That is, this menu affects specifically a specific boot, and if you do not call it afterwards, the computer or laptop will boot as configured in the BIOS.
How to call the boot menu - keys for calling the BIOS boot menu
So, we figured out what the boot menu is in BIOS. Now I’ll tell you what hotkeys you use to call it. There is no standard here. It all depends on the manufacturer of the PC or laptop motherboard and on the version of the BIOS installed there. For example, calling the boot menu asus is different from calling the boot menu on an acer or sony vaio laptop.
In most cases, the key to call up the boot device selection menu is F12 , but some manufacturers use their own key combinations. Special attention You can focus on the boot menu of Samsung and HP. To get to the boot menu of a Samsung laptop you need to press Esc (just one time!). If you click on Esc at least twice, the boot menu will close before it can open. Therefore, you need to calculate and clearly hit the time by pressing hotkey calling boot menu. This can be quite difficult to do without some skill.
Calling the boot menu on HP laptops is also specific. To do this, you first need to click Esc , after which it will appear service menu laptop. In it we already select the desired item (by pressing the hot key). To call the HP boot menu, press F9 .
For some manufacturers, the device to be loaded into the menu is selected using the cursor keys; for others, you need to press a key with a number indicating serial number devices in the list.
Below is a table that is easy to understand. This is a table of correspondence between hotkeys for calling up the menu for selecting the boot device, motherboard manufacturer and BIOS.
Yes, and one last clarification. In some cases, boot menu hotkeys are disabled by default in the BIOS. To be able to use the boot menu, you need to enable it in the BIOS settings. Typically this function is called F12 Boot Menu . To enable this feature, you must set its value to Enabled .
In addition to the keys for calling the boot menu, the table shows keys for entering the BIOS.
| Manufacturer/device | BIOS version | Boot menu key | Key to enter BIOS |
| Mat. MSI boards | AMI | F11 | Del |
| Mat. Gigabyte boards | Award | F12 | Del |
| Mat. Asus boards | AMI | F8 | Del |
| Mat. Intel boards | Phoenix Award | Esc | Del |
| Mat. AsRock boards | AMI | F11 | Del |
| Asus laptops | Esc | F2 | |
| Acer laptops | Inside H2O | F12 | F2 |
| Acer laptops | Phoenix | F12 | F2 |
| Dell laptops | Dell | F12 | F2 |
| HP laptops | Esc -> F9 | Esc -> F10 | |
| Lenovo laptops | AMI | F12 | F2 |
| Packard Bell laptops | Phoenix Secure Core | F12 | F2 |
| Samsung laptops | Phoenix Secure Core | Esc (once, pressing again exits the menu) |
F2 |
| laptops Sony Vaio | Inside H2O | F11 | F2 |
| Toshiba laptops | Phoenix | F12 | F2 |
| Toshiba laptops | Inside H2O | F12 | F2 |
Good day everyone!
Why memorize something you don't need every day? It is enough to open and read the information when you need it - the main thing is to be able to use it! I usually do this myself, and these hotkey signs are no exception...
This article is for reference, it contains buttons to enter the BIOS, to call boot menu(it is also called Boot Menu). Often they are simply “vitally” necessary for reinstalling Windows, when restoring the computer, setting up the BIOS, etc. I hope the information will be relevant and you will find the treasured key to call the desired menu.
Note:
- The information on the page will be updated and expanded from time to time;
- You can see the buttons for entering the BIOS in this article (as well as how to enter the BIOS in general :)):
- At the end of the article there are examples and explanations of abbreviations in the table and a description of the functions.
NOTEBOOKS
| Manufacturer | BIOS (model) | Hotkey | Function |
| Acer | Phoenix | F2 | Enter Setup |
| F12 | Boot Menu (Change Boot Device, Multi Boot Selection Menu) |
||
| Alt+F10 | D2D Recovery (disk-to-disk system recovery) |
||
| Asus | AMI | F2 | Enter Setup |
| ESC | Popup Menu | ||
| F4 | Easy Flash | ||
| Phoenix Award | DEL | BIOS Setup | |
| F8 | Boot Menu | ||
| F9 | D2D Recovery | ||
| Benq | Phoenix | F2 | BIOS Setup |
| Dell | Phoenix, Aptio | F2 | Setup |
| F12 | Boot Menu | ||
| Ctrl+F11 | D2D Recovery | ||
| eMachines (Acer) | Phoenix | F12 | Boot Menu |
| Fujitsu Siemens | AMI | F2 | BIOS Setup |
| F12 | Boot Menu | ||
| Gateway (Acer) | Phoenix | Click mouse or Enter | Menu |
| F2 | BIOS Settings | ||
| F10 | Boot Menu | ||
| F12 | PXE Boot | ||
| HP (Hewlett-Packard)/Compaq | Insyde | ESC | Startup Menu |
| F1 | System Information | ||
| F2 | System Diagnostics | ||
| F9 | Boot Device Options | ||
| F10 | BIOS Setup | ||
| F11 | System Recovery | ||
| Enter | Continue Startup | ||
| Lenovo (IBM) | Phoenix SecureCore Tiano | F2 | Setup |
| F12 | MultiBoot Menu | ||
| MSI (Micro Star) | * | DEL | Setup |
| F11 | Boot Menu | ||
| TAB | Show POST screen | ||
| F3 | Recovery | ||
| Packard Bell (Acer) | Phoenix | F2 | Setup |
| F12 | Boot Menu | ||
| Samsung | * | ESC | Boot Menu |
| Toshiba | Phoenix | Esc, F1, F2 | Enter Setup |
| Toshiba Satellite A300 | F12 | Bios |
PERSONAL COMPUTERS
| Motherboard | BIOS | Hotkey | Function |
| Acer | Del | Enter Setup | |
| F12 | Boot Menu | ||
| ASRock | AMI | F2 or DEL | Run Setup |
| F6 | Instant Flash | ||
| F11 | Boot Menu | ||
| TAB | Switch Screen | ||
| Asus | Phoenix Award | DEL | BIOS Setup |
| TAB | Display BIOS POST Message | ||
| F8 | Boot Menu | ||
| Alt+F2 | Asus EZ Flash 2 | ||
| F4 | Asus Core Unlocker | ||
| BioStar | Phoenix Award | F8 | Enable System Configuration |
| F9 | Select Booting Device after POST | ||
| DEL | Enter SETUP | ||
| ChainTech | Award | DEL | Enter SETUP |
| ALT+F2 | Enter AWDFLASH | ||
| ECS (Elite Group) | AMI | DEL | Enter SETUP |
| F11 | BBS POPUP | ||
| FoxConn (WinFast) | TAB | POST Screen | |
| DEL | SETUP | ||
| ESC | Boot Menu | ||
| GigaByte | Award | ESC | Skip memory test |
| DEL | Enter SETUP/Q-Flash | ||
| F9 | Xpress Recovery Xpress Recovery 2 |
||
| F12 | Boot Menu | ||
| Intel | AMI | F2 | Enter SETUP |
| MSI (MicroStar) | Enter SETUP |
HELP (according to the above tables)
BIOS Setup (also Enter Setup, BIOS Settings, or simply BIOS)- this is the button to enter the BIOS settings. You need to press it after turning on the computer (laptop), and preferably several times until the screen appears. The name may vary slightly depending on the equipment manufacturer.
Boot Menu (also Change Boot Device, Popup Menu)- a very useful menu that allows you to select the device from which the device will boot. Moreover, to select a device you do not need to go into the BIOS and change the boot queue. That is, for example, you need to install Windows OS - press the button to enter the Boot Menu, select installation flash drive, and after rebooting, the computer will automatically boot from the hard drive (and no unnecessary BIOS settings).
Example Boot Menu - HP laptop (Boot Option Menu).
D2D Recovery (also Recovery)- Windows recovery function on laptops. Allows you to quickly restore the functionality of the device from a hidden hard section disk. To be honest, I personally don’t like using this function, because... recovery in laptops is often “crooked”, works clumsily and there is not always a choice detailed settings“how and what”... I prefer installation and Windows recovery With bootable flash drive.
Easy Flash - used for BIOS updates(I don’t recommend using it for beginners...).
System Information - system information about the laptop and its components (for example, this option is available on HP laptops).
PS
Thanks in advance for any additions to the topic of the article. Your information (for example, the buttons to enter the BIOS on your laptop model) will be added to the article. All the best!
When installing operating system You must go to the Boot Menu to tell your computer which device to boot from. This is also necessary when you need to start from a Live CD or bootable USB flash drive. Today I will tell and show you how to enter Boot Menu How on motherboards PCs and laptops.
Just like to enter BIOS or UEFI you need to press special key(F2 or Del), there is also a specific button to call up the boot menu. As a rule, these are the F11, F12 or Esc keys, but there are exceptions. Usually, when you turn on the computer, under the splash screen you can see a key that is responsible for calling the Boot Menu.
You can, of course, do without the Boot Menu by simply selecting a certain order for loading devices in the BIOS, but if you want to boot one-time (checking for viruses or installing a system), then I would advise using the boot menu, because it is much faster.
So, why do you need the Boot Menu at all - you ask. This menu shows a list of devices connected to the PC from which you can boot (flash drives, CDs, hard drives) for further installation of the system or for testing components.
Logging into the Boot Menu in Windows 8 and Windows 10
If you are the proud owner of a laptop on which Windows 8, 8.1 or Windows 10 was originally installed, then you may not be able to enter the Boot Menu. I’ll explain why: shutdown in these systems is not complete, since it is more like hibernation, so when you press F11, F12, Esc, the boot menu may not open. There are several ways to fix this:- hold down the Shift button when selecting “Shutdown” and then the PC should turn off completely;
- disabling quick system startup - in G8, go to the Control Panel,
Go to "Power Supplies"
On the left, click on "Power button actions"
Disable the “Enable fast startup” item (you can do this even if not on a laptop).
Logging into the Boot Menu on Asus laptops and motherboards
Almost all desktop computers Asus, to enter the boot menu you need to press the F8 button immediately when the computer turns on. If we press F9 or Del, we will get to the BIOS.
Regarding laptops, it's a little confusing. The Esc key opens the boot menu on modern models, on older laptops the F8 key works and mainly on models whose names begin with the letter k or x. In short, if the Esc key does not bring up the Boot Menu, then we reboot and try pressing F8.
Logging into the Boot Menu on Lenovo laptops
To call up the boot menu on Lenovo laptops Just press the F12 key. If you want to use additional options downloads, click additional key with an arrow,
Logging into the Boot Menu on Acer laptops
On all Acer laptops and all-in-one PCs for call Boot Menu is the F12 key when turned on. But laptops from this company have one unpleasant feature- the ability to call the boot menu is disabled in the BIOS settings. To fix this, let's get into the BIOS by pressing the F2 key. Now let's find the "F12 Boot Menu" parameter and activate it so that the word Enabled appears next to it. All that remains is to save the settings and exit the BIOS.
Below in the table you can see all other laptops and the key to call the Boot Menu and BIOS:
I hope the information in this manual was useful to you. If you have any difficulties getting into the boot menu, then write in the comments, I will try to help!