Is it possible to repair an iPhone? Is it possible to repair an iPhone yourself? Diagnosing iPhone mechanical problems at home
We answer: it is possible, but carefully. You should only start troubleshooting your iPhone if:
the damage is not too serious;
you have the necessary parts of appropriate quality;
are you good at repairs? cell phones and you know exactly what to do.
Keep in mind, even if you know how to handle technology, this does not mean that any damage to your iPhone can be repaired at home. In many cases, it is better not to take risks and immediately contact a professional so that you do not have to deal with even more damage caused by your inept intervention.
So, what can you fix yourself?
1. If moisture gets inside your device, the phone should be turned off immediately and dried thoroughly. It is better to use a household hair dryer, but in warm mode, and in no case hot air. You should blow out the air carefully, shaking the iPhone periodically to remove water droplets from hard-to-reach places. Do not forget to remove SIM cards and memory cards before these procedures.
One of the ways to rid the iPhone 5 of water that has gotten inside can also be rice cereal. The phone must be placed in a plate filled with rice so that excess moisture is absorbed into the cereal.
2. One of common problems with iPhone 5 is screen damage. A broken display leads to damage to the touchscreen, because... iPhone glass and touchscreen form a single whole. Changing the screen at home is quite difficult, although not impossible. Keep in mind that you must know exactly how to proceed so that trying to solve the problem yourself does not lead to even more damage.
3. The appearance of cracks on the case is also a very common problem among iPhone 5s. Damage to the housing can occur even with a small impact, especially if you are not using protective cover. You can order a new case, as well as a screen, online and try to install it yourself. The process of replacing the case does not take much time and is essentially not that complicated; the main thing is to be careful not to accidentally damage the chips or move the screen.
4. If one day you find that the on/off buttons on your device have stopped working, do not rush to immediately take your iPhone 5 for repair. You can still fix the iPhone yourself if you are very careful. The situation is complicated by the fact that the iPhone buttons are connected by a cable, so if the buttons malfunction, the entire system has to be replaced.
If, after replacing the cable, the iPhone still works with malfunctions, it means that one of the buttons did not fit exactly into place during the repair process. You will probably still have to contact a service center for help.
5. It happens that the iPhone 5 stops working due to contacts being lost. If you have any knowledge of technology, this type breakdown will not cause you any difficulties in repairing the fault. After opening the iPhone case, visual diagnostics will help you find the cause and carefully solder the contact in place. Try not to damage nearby parts and microcircuits. If you have never done this before, remember that an iPhone is not the gadget on which to practice such skills.
6. Repair iPhone 5 cannot be produced independently if the microcircuits fail. You are advised to contact professionals. Otherwise, when repairing an iPhone at home, you act at your own peril and risk, which threatens the complete loss of functionality of the gadget.
Undoubtedly, you can fix the iPhone 5 yourself, but do not forget that the service center specialists will in any case solve the problem better and more reliably than you.
1) As you might guess, the most popular breakdown apple smartphones - broken glass. In the vast majority of iPhones (except 3g and 3gs), the glass is replaced together with the touchscreen (touch glass), this is due to the fact that in pursuit of smaller sizes and greater performance, this spare part (display module + glass) is produced as a single whole. What’s interesting is that in most cases the sensor continues to work quite well and the question naturally arises: “to change the module or not to change it?” To be fair, it can be noted that if there is only one crack and a small one, you can continue to actively use your gadget without investing additional money in it (people drive with cracked windshields), but if this drawback constantly catches your eye, then it’s better to change it anyway.
There are 3 levels of module quality on the market for iPhone 4 and 4s (copy, HQ and original), and two for iPhone 5 (copy and original). Therefore, you always have a choice between cheaper and better quality. The best way to distinguish an original from a copy is by color rendition and glass; original modules have smooth glass and cannot be left with a permanent marker. Besides more bright colors and more convenient glass, the original modules are more durable.
To protect your iPhone from this damage, it is advisable to use a case (for example, a book case covers the iPhone from all sides, and the bumper may spring back a little when dropped, but will not save you if iPhone will fall on an uneven surface) and a protective film (although in reality it only saves from scratches). Also remember that not all cases are equally useful - the original ones last longer and withstand impacts better, while theirs Chinese copies can fall apart quite quickly and cause a fall themselves if the device falls out of a loose case.
2) The next position in our hit parade of breakdowns is worthy of a broken or badly worn case. IN iphone case 3g and 3gs have a plastic back cover that can be damaged if dropped “on your back”; they also do not stand the test of time well, quickly wear out, crack and begin to look less and less presentable. iPhones 4 and 4c have a separate middle part (it can be damaged by a strong impact or scratched from prolonged use) and a back glass (almost as fragile as windshield). The iPhone 5 has a unibody aluminum back cover, which is quite easily scratched around the perimeter and can easily be damaged as a result of a fall; again, for the sake of small size and weight, the metal thickness is minimal.
How can you protect yourself from this scourge? It’s very simple - most cases somehow protect the case when dropped, and constantly carrying the device in a good-quality case reduces scuffs and scratches to an absolute minimum.
3) Quite often, the trains of people's favorites fail, because there are many of them and they are subject to natural wear and tear. All buttons, sensors, microphones, speakers, cameras and connectors on iPhones are located on one cable or another. For example, on the bottom cable of the iPhone 5 there are: a charging connector, a headset connector, a microphone and an antenna. A cable with a system connector (also called a charging connector) can become damaged as a result of frequent connection/disconnection of the cable, especially if this is done with excessive force and at an acute angle. The cable with the power button fails when it is used frequently and with special force. The same applies to the train Home buttons, which takes on most of the clicks.
To extend their service life there are simple recommendations: use the buttons only when necessary, press them effortlessly, insert the charger and headphones carefully and strictly perpendicular to the connector, it is also not recommended to hang the iPhone by the cable or headphone wire (much less untwist it by the wire).
4) Particularly noteworthy are damage such as moisture ingress and strong impacts. It turns out there is more in common between them than seems at first glance: in both cases the device is damaged in a complex way, the motherboard may be damaged, it can cost a lot of money, but the guarantee stable work no one will have the device after it (it’s like a car that has been in a serious accident - you can return it to its original form, straighten and paint the body, change spare parts, but it will be a completely different car), as a rule, after finishing it they are sold, so as not to take risks. Microcircuits often suffer from a strong impact (as well as from moisture), after which they require replacement, which is lengthy and expensive repairs, and during the repair process, the condition of the device may even worsen, which is warned about in writing on all receipts and verbally when receiving the equipment.
Although our workshop has extensive experience in successfully restoring the most hopeless devices, we are still in some special cases We do not recommend carrying out repairs, and if you still manage to fix it, we can advise you to get rid of the device and buy yourself a new one. (In fact, the advice is quite sincere, and from the point of view of banal pragmatism, you can sell a restored device much more profitably than one that does not turn on or is broken to smithereens).
No case will save your iPhone from a powerful blow against a wall or getting run over by a car, just like it won’t save it from being submerged in water. But still, there are some tips on what to do after the incident: do not try to turn on the device, do not put it on charge (pressing the Home button and the power button at the same time for a few seconds can quickly turn it off), do not try to disassemble your iPhone yourself (usually in As a result, you can only increase the number of breakdowns), quickly take it to good service.
5) After several years of use it breaks down accumulator battery, which is designed for certain number charges/discharges. When fully charged Your his mobile friend If it lasts for half a day with average use, then the diagnosis becomes obvious. It is important that in the service (and we do this for any power-related breakdowns) the device is checked for consumption; if it is too high, then the problem may be a short circuit that occurred as a result of corrosion or impact and replacing the battery will not help you.
To increase the life of your battery, you need to protect your iPhone from overheating (it is advisable not to leave it in the sun). You can also reduce the brightness, turn off the 3G network, Wi-Fi, GPS (especially when you don’t use them), so that one charge lasts longer.
6) There is a problem of non-original network and car chargers. Their use can damage the power controllers and/or charging controller, which leads to dire consequences, sometimes fatal. It was observed that during use non-original chargers, the devices would heat up unnaturally and malfunction (for example, the sensor would slow down)
7) Let us separately consider the problems on program level: freezing, errors when flashing. In many cases, a hard reboot can help (not everyone knows that an iPhone can be rebooted by simply pressing two buttons - the HOME button and the power button until the apple appears). If rebooting doesn’t help, and you can’t flash it through iTunes, feel free to take it to the service. In some cases, firmware errors indicate failure of the memory chip or processor (which usually happens after a strong impact)
8) Quite often, with small impacts, problems with sound arise (in most cases, the interlocutor stops hearing you, or the sound is interrupted for several seconds). If replacing the lower cable does not help, then it becomes obvious that the problem is in the Audio chip. You can check this like this - if during a conversation the microphone does not work or the sound is interrupted, but when recording a voice recorder everything is fine - then most likely the problem is in the microcircuit. In such cases, it must be changed.
Articles and Lifehacks
Accidentally broken iPhone can cause a real tragedy, especially if its owner acquired it relatively recently (even knowing it, knowledge can be difficult to apply). A blow or sudden drop of the device can seriously damage the structure of the display itself, which will cause “broken” pixels to appear, and the image on the screen will not be fully viewable – unless, of course, it disappears completely. However, it is possible to replace faulty parts of the liquid crystal display with new and original ones, and the iPhone will work again without any restrictions.
Is it likely that your iPhone will break?
From the very beginning of the product's appearance Apple On the domestic market, quite a lot of information has appeared on the Internet about American experimenters who conducted various studies in order to find out all the possibilities, as well as the advantages and disadvantages of new devices. The results of these studies turned out to be quite interesting. Thus, only 9.9% of all products, including the iPhone, failed due to the fault of the manufacturer itself. Moreover, each new model always turned out to be better than the previous one. And finally, over 20% of smartphone damage was caused by careless handling by the owner himself. As a rule, it was the screens that were broken (66% of the total number of breakages).
So, the main reason that an iPhone fails is careless handling by its owner. In addition, do not forget that Apple has never positioned its products as water-resistant or particularly durable.
Where should I take my broken iPhone to get repaired?
Repairing a device such as a broken iPhone is one of the most difficult procedures. That is why it is recommended to entrust it to service center professionals. What is the main advantage of such a renovation? Usually, upon completion, a specialist conducts a full diagnosis of the device using equipment specially designed for this purpose. Even if it is obvious that only the screen is broken, checking is still mandatory, since it can reveal other, internal and less noticeable damage.
The design of the display is quite fragile, so in order to break the screen, its owner will not need much effort. Cracks on the edges can even appear if the owner, using it carelessly, drops it on the floor covered with soft carpeting.
If the user does drop his iPhone and sees that the display is broken, he should not attempt to repair it at home. In addition to the fact that repair is a complicated procedure, you will need a new and working screen. Regardless of the model of the device, it is recommended to immediately contact service center, specializing in servicing Apple products. There the device will be repaired and diagnosed, after which it will again be able to delight with its reliable and high-quality work.
A very common reason for which repairs have to be made modern phones, such as an iPhone, is when liquid gets into the inside of the gadget. Moisture gets into electronic circuits through headphone ports, charging connector, microphone, various microcracks. Today there are many offers in the service sector. This includes calling a computer technician to your home and assistance from specialists who understand Apple products. But there are some things you can do with your own hands.
Getting rid of moisture
In the event that liquid has penetrated into the filling of your smartphone, you need to quickly:
- turn it off;
- dry the boards.
You can use a regular household hair dryer for this. You need to pull out the tray with the SIM card, and then blow a stream of heated air into the phone (do not use a hot stream!). Don’t forget to shake the gadget so that the drops that are inside come out of hard-to-reach places. Very effective method One that helps combat moisture is the use of a product such as rice grits. You need to put the iPhone in a plate with rice so that the liquid is absorbed. If the actions are unsuccessful, you will have to seek help from specialists from the service center.
If the display is damaged
A very common problem associated with mobile technology, is a fall of the device, causing the screen to break. It is known that the glass in an iPhone and the touchscreen are one whole. Accordingly, if the glass is damaged, then there is no way to do without replacing the touchscreen. It is not easy to cope with this matter on your own; you need to contact the service. But sometimes the damage is not very serious, and the smartphone functions normally. Worth applying protective film to the display. Thanks to this, you can ensure that moisture does not penetrate into the phone through cracks.
Things to remember
A very common problem among owners of Apple devices is frame damage. This happens not only due to the fall of the gadget, but also when it is impacted by various sharp and hard objects, such as keys. Because of this, the functions of the side keys are impaired. Of course, you need to use special covers.
Sometimes an iPhone user must solve a problem related to faulty keys. The buttons are connected by one cable, therefore, if one fails, the entire system must be replaced. The cable must be changed very carefully. The keys should fit exactly in their place after replacement. Only in this case will they work normally.
The first thing I would like to note when your iPhone gets into water is that you should not be too lazy to take the device to a service center, only there you can dry it completely and stop the harmful effects of water. We will be glad if you contact our service centers:
So, what to do when your pet has been in the water?
There are currently thousands of various options iPhone accessories that can protect your device from minor scratches and minor falls.
But, unfortunately, very few of these accessories can protect the device from moisture and, as a rule, such accessories belong to the highest price segment. According to statistics, not many people are willing to spend significant sums on such protection, and besides, such accessories do not look very aesthetically pleasing, and this is an important factor for many iPhone owners.
But what to do if iPhone got wet or himself iPhone fell into water? Today we will give some small tips and hope that this article will be useful for you.
First steps if iPhone falls into water
Firstly Naturally, you should remove the iPhone from the water as quickly as possible or stop interacting with moisture. The longer the device interacts with water or any other liquid, the greater the likelihood of multiple oxidations occurring on the motherboard and the less likely it is that the iPhone can be repaired.
Second(and most importantly) - you need to quickly turn off the iPhone, because... when the device gets into water, in addition to chemical oxidation reactions inside the phone, microscopic short circuit, which can lead to complete inoperability of the device. In addition, it is highly recommended turn off iPhone in a standard way, remove the battery from it as quickly as possible, because even when turned off, it supplies voltage to the board.
Of course, even after moisture gets in, the device may work quite correctly for some time, but you shouldn’t be happy. Over many years of work in the service industry Apple technology, we saw different cases, what happens to devices if they continue to be used after significant exposure to moisture. The photo below is very typical. It shows the main iPhone board, which was used for two weeks after the “immersion”. It can no longer be restored.
There are many myths and not very correct recommendations on what to do if water gets into your iPhone. Of course, due to their prevalence, people remember them first and try to put them into practice. But not all such recommendations can be useful, and some, on the contrary, can make the situation even worse.
The most common recommendation is that after wiping the iPhone with a dry towel or microfiber cloth, place the device in a container with rice. This method can help, but only partially and only in cases where the moisture ingress was not very significant.
Of course, rice absorbs moisture vapor very well, but it cannot help in any way if water gets on the internal elements of the board - the corrosion process has already started and from time to time the elements motherboard they will simply begin to rot. In addition, some types of rice may leave small crumbs that will end up inside the device.