How to make a vacuum cleaner more powerful? An easy and homemade way to increase the traction of a vacuum cleaner. How to increase the suction power of a car vacuum cleaner.
Samsung vacuum cleaners are widely used. They do their job well and are not too expensive. As you know, in mass production they adhere to the principle: the excellent is the enemy of the good. Of course, you can take the path of increasing constructive improvement, but this will lead to an increase in the cost of the product and its less competitiveness.
So, during operation, vacuum cleaners known throughout the world are found to have certain shortcomings that lead to a decrease in their technical and operational characteristics.
Thus, the dust bag, filling up during operation, begins to block the hole in the partition between the suction fan and the vacuum chamber, which is connected using a corrugated hose and a tube with a cleaning brush. Structurally, this hole is covered with a piece of thin foam rubber to prevent dust from getting onto the fan.
As a result, as the dust bag fills with debris, the suction power of the vacuum cleaner begins to gradually decrease and, in the end, may disappear completely. What can be done in this case?
Ways to improve the design of a vacuum cleaner
The idea of getting rid of the specified defect found in a vacuum cleaner is understandable. It is necessary to prevent the dust bag from blocking the suction opening as it is filled. In other words, there should always be a small gap between them for free air suction.For this purpose, a sufficiently rigid (metal or plastic) grid is installed in front of the suction hole on the side where the garbage container is located, which will not bend under the influence of the air flow and the pressure of the bag filled with garbage.
It is this that will be guaranteed to create the required gap.
Another noticeable flaw in this vacuum cleaner is related to the flexible hose connector. When it is secured in the vacuum cleaner body with a latch, its tube does not extend beyond the inner wall of the chamber in which the dust collector is installed.
As a result, it turns out that a significant portion of the sucked air bypasses the dust bag and, flowing around it, leaves the vacuum cleaner without any benefit. How to cope with such a disadvantage?
To do this, you need to take a piece of plastic tube of the appropriate diameter and length, which should be sufficient to fit into the hole of the still empty bag.
We insert this piece of tube into the hole of the connecting element, place it on suitable glue, wait for it to dry and the household appliance is ready for use. After such modification, all the sucked in dirty air enters the bag and dust and debris completely settle there.
To expand the capabilities of the vacuum cleaner, if the kit includes only one brush, you can use attachments from other brands of vacuum cleaners. Perhaps with some minor modifications that almost anyone can handle.
Moreover, during the operation of the modified vacuum cleaner, another advantage was discovered: it continues to properly remove dust even when the bag is full. This is the suction force that causes the garbage to be compressed into the container.
Usually good ideas have many useful manifestations. The data, for example, almost completely captures the dust, which settles in the dust collector, and the exhausted air does not pollute the engine, in particular its bearings and brushes, which wear out less. Also, the load on the electric motor is reduced, since the hole behind the boot is not blocked.
The only thing to remember is that before removing the filled bag from the vacuum cleaner, you must disconnect the flexible hose. But the dust collector compartment always remains clean and there is no need to remove dust from it, which is not so easy due to its configuration and the presence of stiffening ribs.
Two final comments
Choosing a plastic mesh will protect the vacuum cleaner body from scratches. When using a metal mesh, rubber or plastic strips can be easily attached to its edges.Epoxy or polyurethane glue is often used to glue plastic parts. The connection will not be very strong and durable. From time to time the procedure will have to be repeated.
To glue, or rather dissolve and solder plastic, you first need to find out its type. Then find a suitable solvent. But as a result, the connection will be “tight”.
During the active use of household appliances, situations may arise when their performance is no longer sufficient for comfortable use. This is especially noticeable with vacuum cleaners, where it becomes impossible to finish cleaning properly. In this case, you need to know how to increase . Let's look at several ways to do it yourself.
If the efficiency of your vacuum cleaner gradually decreases over time, you can fix it yourself. two reasons such behavior of his. These include:
- Incorrect or loose assembly of device parts.
- Clogged filters.
If the device is assembled incorrectly, and it does not have a function to protect against incorrect assembly, then the device may simply work with less efficiency.
If the unit parts are not installed tightly, the additional air drawn in will significantly impair the operation of the device. In these cases, an increase in power is possible after disassembling and subsequent correct high-quality assembly of the unit.
You should definitely check the filters of the vacuum cleaner; they are most often the reason for the decrease in its suction.
Depending on the device model, there may be up to 4 filters, and you need to check the status of each of them. Depending on the type of filter, it may need to be replaced or simply dry or wet.
What to do if there is a sudden change in power
If during the cleaning process the suction efficiency of the unit drops sharply, then most likely the cause will be an object stuck in the tube. Solving this problem is very easy. You need to turn off the device and check the condition of the tube against the light. If you find a piece of paper, a small toy or other object, simply remove it and the device will work properly again.
However, a situation may also occur when, during cleaning, the power switch lever on the device body was accidentally touched. If this is indeed the case, then simply return the lever to its previous position.
In addition, there is also a lever on the tube that controls the suction of the device. Perhaps this lever was accidentally pressed, and a hole opened into which excess air began to be sucked in, which also reduced the efficiency of the device.
Having corrected all these points, you can continue cleaning as planned. If all these measures do not receive the proper response from the device, then you will have to turn to qualified specialists for help.
When using household appliances, we often encounter situations where their power drops, which reduces the performance of the devices and the comfort of their use. This is especially true for vacuum cleaners, when it becomes impossible to finish cleaning efficiently. What influences the drop in their power and how to restore it - more on that later.
A decrease in vacuum cleaner power can occur in different ways. If this is observed gradually over time, then the reasons may be incorrect or loose assembly of parts, or clogged filters.
Devices that are assembled incorrectly perform less efficiently than those that are assembled in full accordance with the technology. If the parts are not tightly arranged, additional air is drawn in outside the working units, which leads to a decrease in the productivity of the units and a drop in their power. The latter can be increased only by disassembling the vacuum cleaner and reassembling it correctly.
The first thing you need to pay attention to when there is a gradual drop in power is the condition of the vacuum cleaner filters. This is where most often lies the reason for the decrease in unit performance.
There are many different vacuum cleaners available today. They may have one filter, but there are models with four filters. You need to check everything and decide based on their condition whether to replace them or you can limit yourself to cleaning.
If the filter in the vacuum cleaner is in the form of a bag, then it is worth checking not only the level of its filling with debris and dust, but also the integrity of the fabric. If the unit has an aquafilter, then first pour water out of it, after which it is washed.
If the power drop in the vacuum cleaner occurs suddenly, then the most common cause of the situation is an object stuck in the hose. The problem can be easily solved: the unit is turned off; the tube is checked for clearance; if any blockage is detected, it is removed by pushing it with a long object.
A sharp loss of vacuum cleaner power can occur when you accidentally turn the power control lever, which is on the body and on the hose handle. The unit's functionality is restored after it is brought to the desired position.
If all the actions described above did not lead to the restoration of the previous power, then the reason is most likely problems with the electric motor or electronics of the vacuum cleaner. This can only be corrected by contacting a specialized workshop for help.
The household appliances market presents a wide range of different vacuum cleaners: industrial, household, portable, hand-held and others. They all differ in size, functionality, power level and, of course, cost. It’s good to have equipment for all occasions, but what to do if, for example, a renovation is planned that requires a construction vacuum cleaner? Its price is quite high, but whether it will be useful in the future is unknown. In such cases, you can make a powerful vacuum cleaner with your own hands, giving it all the necessary functions yourself, using improvised means.
How to increase power without turning to professionals
There are frequent situations when the power of a working vacuum cleaner begins to decrease over time. There are several reasons that explain this behavior of the equipment - you can eliminate them yourself, without contacting service center employees.
| Cause | Consequences | Solutions |
| Incorrect (including loose) assembly of device elements | If the vacuum cleaner does not have special fuses, improper assembly may cause reduced efficiency of the vacuum cleaner. Incorrectly installed parts allow air to pass through and reduce the efficiency of the device. | disassembly and subsequent high-quality and tight assembly of the vacuum cleaner |
| Dirty filters | clogged filters have poor throughput, which affects the power of the vacuum cleaner | cleaning reusable and replacing disposable filters |
| Clogged or ruptured garbage disposal | a clogged bag significantly reduces suction power, and holes in the material allow air to pass through | replacing a disposable garbage bag or high-quality cleaning of a reusable dust container (with rinsing and thorough drying). If you have an aquafilter, you should replace the water in it and rinse the container |
What to do if there is a sudden change in power
It happens that a working vacuum cleaner suddenly loses suction power. This behavior of the device is most often explained by a clogged telescopic pipe or hose. To solve this problem, you should unplug the vacuum cleaner from the outlet and visually (using the light) check the condition of the pipe. You can also use a soft wire to push through the accumulated debris.
If this does not help, you need to pay attention to the brush.
There are cases when the user accidentally touches the power switch lever located on the device body, or opens the shutter on the tube (when the air flow comes out of it, the suction power also decreases).
Refinement of a construction vacuum cleaner
Many construction vacuum cleaners, despite their high power level and large waste containers, are often equipped with filters that are not large enough. This approach does not affect the quality of cleaning during a short period of work. However, in case of prolonged operation it shows a significant decrease in suction abilities. Therefore, many users independently make changes to the filtration system, modifying and improving it.
To replace the pleated filter of an industrial vacuum cleaner, a car cleaning system is usually used. In order to choose it correctly, you must first measure the diameter of the cartridge into which the filter is inserted, as well as the height of the vacuum cleaner tank.
- First of all, install a metal pin into the hole located at the top of the cartridge and fix it tightly. In this case, the diameter of the filter itself should be several centimeters larger than the diameter of the cartridge, for small gaps on the sides.
- You should pay attention to the location of the mounting slots at the bottom of the cartridge - the filter should fit exactly behind them. Otherwise you will need to file them down.
The advantages of this method are undeniable:
- a significant increase in the suction power of the vacuum cleaner;
- prolongation of stable operation of the vacuum cleaner due to a larger filter surface;
- cost savings (on average, the cost of car filters is two to three times lower).
A simple modification to a cheap car vacuum cleaner
The car equipment market presents a wide selection of car vacuum cleaners. However, the cost of many of them is quite high, and cheap Chinese analogues cannot satisfy users with their power level. If you only have a low-quality car vacuum cleaner, you can upgrade it yourself, at home.
To do this, the first step is to figure out what exactly negatively affects the suction level of the device. After disassembling such a vacuum cleaner, you can easily notice that the main disadvantage is the large number of gaps between its elements, which allow air to pass through, thereby reducing the overall power. This indicator can also be affected by a deteriorated mesh that acts as a filter.
The main materials you will need are FUM tape about 1.5 cm wide for sealing, as well as a piece of non-woven fabric that can replace a leaky filter.
The modification process is extremely simple:
- The filter is covered on top with a prepared piece of material (cut according to preliminary measurements), after which it is secured with a part installed on top.
- All spare parts that have gaps during assembly are wrapped with a layer of fume tape. The car vacuum cleaner is put back together.
Modification of any vacuum cleaner with an electronic controller (dimmer)
Many vacuum cleaners are equipped with a power regulator on the body. This function is extremely convenient when working with different surfaces. However, not all models are equipped with a dimmer, but even those that have such a nice addition initially may lose it over time, since the boards often burn out. In this case, the regulator can be installed independently. To do this, you will need any user-friendly regulator whose power range can withstand the power of the vacuum cleaner. Often the connection diagram is immediately indicated on the packaging.
They all have a different structure, the simplest one is discussed below:
- the wire from the coil goes to the switch;
- in turn, from the switch it goes to the engine, but through an installed regulator (power adjustment is carried out through contact 1-2);
- Contact 3-4 is connected to the button installed on the body of the vacuum cleaner.
The board can be attached in any convenient way, for example, with double-sided tape.
Not everyone can afford to purchase new household appliances. Thanks to this article, everyone can learn how to increase the power of a vacuum cleaner at home with their own hands. Today there are many different methods. Therefore, if you notice that your vacuum cleaner has become worse in performance, you should not immediately panic and look at the prices for new equipment. With the help of some tips you can eliminate this problem.
How to increase the power of a vacuum cleaner with your own hands without submitting for repairs
If the performance of the vacuum cleaner has deteriorated over time, you can eliminate this factor yourself. How to increase absorption? There are only two main reasons why this nuance can arise:
- The assembly of parts was not carried out according to the instructions, so some parts were fastened incorrectly or not completely.
- Dirty, uncleaned filters.
The first thing to do is check the filters before use. Most often they are the cause of poor absorption. Depending on the company and model of the vacuum cleaner, the number of filters will depend. The maximum quantity reaches 4 pieces, you need to check each one separately. If the filter is broken or cannot be cleaned, it must be replaced. If there is still a chance of cleaning, it is better to use the wet method. Models that use a bag to collect garbage require additional inspection. In this situation, you need to check whether the bag is damaged and how full it is. It is recommended that if the container is 80% full, it is first cleaned and then replaced.
Devices that have a container for collecting dirt in the form of an Aqua filter are cleaned using the following method:
- First, you need to throw out the dirty water.
- Wash the filter container.
- Pour clean water and replace the filter.
If the vacuum cleaner does not have significant breakdowns, then the 2 above methods should help you. As practice shows, 85% of people who are faced with the problem of poor absorption are solved using these methods.
Advantages and disadvantages of filters
Here we will look at the advantages and disadvantages of each type of vacuum cleaner filter. There are three main types of vacuum cleaners:
Bagless vacuum cleaners are cyclonic or, as they are also called, container vacuum cleaners.
Detergents that work with water contain an aquafilter.
And the most common type of device is one containing a classic bag. Suitable for both dry and wet cleaning. Instead of a bag there may be a dust collector.
These types have a huge range of different models, among them there are those that leave satisfied customers, but also that leave only disappointment.
Cyclonic
Vacuum cleaners do not contain dust collectors or bags. Thanks to modern technology, you no longer need to use Dyson's invention. European manufacturers for a very long time did not want to produce this type of vacuum cleaner, knowing that they had many disadvantages, but consumer desire turned out to be higher. They appeared on trading floors and store shelves quite recently, about 5 years ago. At that time, they had a high cost, and not everyone could afford to buy one.
Today, many users of cyclone filters are disappointed with their purchase. It remains to understand why, and for this we need to consider the pros and cons:
- It has very good advertising, thanks to which the vacuum cleaner has become very popular
- No need to spend extra money on bags. In European countries, you save a couple of dollars per month.
- They do a good job of cleaning the air from dust, which is well removed using a rotating vortex, that is, a cyclone.
- If the container is almost full, this does not affect the suction of the vacuum cleaner; there is no need to increase it.
There are advantages, but they are minor. Now let's look at the disadvantages:
With aqua filter
As soon as these models were released, they were very popular for cleaning in hospitals, special industries or laboratories. Both before and now they are expensive, since they carry out dry and wet cleaning at the same time. Now let's look at why they became famous.