To protect the iPhone 7 screen from various cracks, scratches and chips, experts recommend sticking a special protective glass. It will also help protect mobile device from mechanical damage during the fall.

In addition, it is very simple to purchase and stick protective glass on an iPhone 7 instead of a damaged one, rather than doing a similar procedure with a smartphone screen.

Let's figure out how to properly stick a protective glass on an iPhone 7.

Preparatory stage

Before you start directly gluing the protective glass on the iPhone 7, you need to carry out preparatory work. It includes two stages:

1. Cleaning the screen directly mobile phone- you need to carefully examine the front surface of this device. Existing areas of contamination should be removed. For these purposes, use a piece of microfiber cloth or special cleaning wipes. household appliances(they are treated with an alcohol solution to get rid of various stains).
   If you use an alcohol wipe, then make sure that there are no wet marks left on the screen from its use.
2. Dust removal - use the blue absorber for small dust particles. It has an adhesive base, thanks to which you can remove even dust particles that are invisible at first glance. By alternately sticking and peeling it onto the iPhone 7 screen, you will achieve a perfectly clean surface.

Glass gluing process

When cleaning of the device is completed, you can begin directly gluing the glass.

You need to pick up the protective glass and remove the pre-installation surface. The protective film must be removed exactly at the moment when the glass is installed. Because otherwise, dust particles may fall on its surface.

The glass holes should be aligned with the sensors and the “Home” button on the mobile device.

You need to start the process of gluing the protective glass either from the top or from the bottom (whichever is convenient for you). When gluing glass, make sure that there are no air bubbles underneath it, as they can be very difficult to get rid of.

When the protective glass is glued to the iPhone 7 screen, you need to carefully inspect the mobile device again. If no air bubbles or dust particles appear between the screen and the protective glass, then you have successfully completed the task and can use your smartphone.

I’ll say right away that putting protective films on the screen has always seemed stupid to me. Well, really, it’s like a remote control in a bag. People who did this were usually guided by two reasons. Firstly, so as not to catch scratches on the screen and subsequently sell the phone for more money in excellent condition. Secondly, to get some additional options. Anti-glare films are available, for example. Or matte, with protection from peeping neighbors in transport.

There is also a category of people who receive their devices with a film already attached, and they simply do not remove it. I had a friend who stubbornly did not remove the film from her smartphone with the inscription “Please, remove the protective film.” Some second-tier manufacturers glue films (protective, not transport) to the screens of their devices at the factory by default. This is relevant for budget smartphones and tablets whose screens have plastic rather than glass protection.

But enough about the films. Their alternative in the form protective glasses I became interested a year ago when I broke the glass on my iPhone (then 5S). After replacement, the phone was poorly assembled, and new screen turned out to be worse quality. So my new “six” received protective glass right away, you never know. And then I ordered several more different glasses to compare them.

So, what are the advantages of protective glass (as opposed to film):

1. Most likely, the original glass of the screen will save you in the event of an unsuccessful fall (I confirm - I had experience).

2. It is much easier to stick glass than film, under which any speck of dust bubbles up.

3. Glass is more pleasant to the touch, it has a good oleophobic coating and scratch protection.

4. The glass is stronger and holds more securely; it cannot be peeled off accidentally, for example, when putting the phone in a narrow pocket.

There are no downsides, in my opinion. But there are some peculiarities. The glass is thicker than the film, but personally I don’t feel it in any way. It cannot noticeably thicken or make the phone heavier. And if you have a smartphone/tablet of some very rare model, then you may not find suitable glass for it. But you can’t cut it like a film.

What types of glass are there?

Protective glass is a simple thing, like five kopecks, but it has its own characteristics. Firstly, thickness. Usually 0.3 mm, but 0.26 mm can also be found. I don't see any difference between these options. In addition, the description often contains the expression “2.5D”. This means that if the edges of the glass are slightly rounded, they are more pleasant to touch.

There are also “3D” glasses, they are designed for the currently popular phones with rounded screen edges. For example, Samsung Galaxy S6 Egde and iPhone 6/6S. True, technically we are most often not talking about solid curved glass; they are very fragile and difficult to produce. Manufacturers are getting out of the situation different ways. The coolest one is when the glass is the size of a phone screen, but not rounded. In this case, dirt and dust gets clogged under it. A more elegant solution is when curved metal sides are attached to ordinary glass (and to keep it all in place, there is a protective film on top). It looks good, although it's not for everyone. The metal edges seemed sharp to me.

On this moment my favorite is glass with carbon fiber frames. Looks like the original iPhone panel. But it is relatively expensive (don’t buy cheap analogues, they look bad).

Many buyers often ask us the question: how to stick protective glass for iPhone 7? There is nothing difficult about this. Just watch the video carefully and the whole process will be “in the palm of your hand.”

If you doubt your capabilities, we advise you to consult with our specialists in advance using the contact phone number or the specified email address.

Installing a protective glass on iPhone 7 includes the following steps:

Cleaning the screen

Carefully inspect the front surface of the smartphone and remove local dirt using a microfiber cloth and an alcohol wipe.

It is important to know! After using a wet wipe, be sure to check for any remaining stains on the gadget’s screen.

Removing dust

Take a blue adhesive absorbent for fine dust particles. Alternately peel and stick it on the iPhone 7 screen until the ideal surface frequency

Glass installation

Take the protective glass in your hands and remove it from the pre-installation surface. Align the glass holes with the sensors and the "Home" button on your smartphone. Start the gluing process from the bottom or top of the gadget. Smoothly complete the installation on the opposite side, promptly expelling the air from under the protective glass.

Attention! Before peeling off the protective glass from the transport pad (pre-installation), hold it parallel to the surface on which your smartphone is located. Do not flip or tilt the screen protector on your iPhone 7 after removing it from the adhesive surface. Otherwise, dust will get on the adhesive part before the installation process begins.

Final stage

Carefully inspect the gadget screen for air particles or dust under the glass. If everything is in order, we sincerely congratulate you on this difficult process. If you find particles of dust or air under the glass, gently lift it and remove any remaining dirt using mini-stickers.

How to properly apply protective glass to iPhone 7? Almost every owner of this gadget faces this question. iPhone 7 is a fairly expensive premium smartphone that requires careful handling. Sometimes falls and blows lead to breakage display module, the replacement of which costs about half the cost of the phone, and sometimes more. To prevent this problem, there is a special accessory - protective glass. It is similar to traditional film, but differs more high density, and, accordingly, provides better protection. However, how to properly glue glass to an iPhone to avoid the formation of bubbles and other unpleasant defects? This is quite easy to do, even at home without special skills and tools. We will discuss in detail how to glue a protective glass on an iPhone 7 below.

The procedure for installing a protective surface is divided into several conventional stages:

1.Preparing the screen.

2.Dust removal.

3. Direct installation of the accessory.

4.Final check, removing air bubbles.

Preparing the smartphone display module

Before gluing the glass on the iPhone 7, you need to prepare the smartphone display. Preparation involves thoroughly cleaning the screen from dust and all kinds of other contaminants. If there is an old film on your smartphone, it must be removed. It is important to thoroughly clean the remaining adhesive layer on the screen. For cleaning, use an alcohol wipe and a microfiber cloth. Usually all this is included with the accessory. If they are absent, use available means. After cleaning, check the screen in the light, if any stains remain, remove them.

How to glue glass to an iPhone: installation procedure

Installing a protective surface is quite simple, the main thing is to act carefully. Before sticking 3D glass on your iPhone 7, be sure to thoroughly wash and dry your hands to avoid leaving grease stains on the screen and glass. Carefully grab the part by the edges and remove it from it protective film. The latter is located on the adhesive side of the accessory, and is usually marked No. 1. There are glasses on which there is only one film, on the adhesive side, and with reverse side it may not exist. Align the protection with the display, the holes for the speaker and the center button should perfectly match. Once the protective surface is level, carefully place it on the display. The accessory has a special silicone layer on the bottom, so you don’t need to press it down, it will stick on its own. You can either place the entire part on the display surface at once, or start from the top or bottom, it all depends on what is more convenient for you.

Important! Remove the shipping film very carefully, do not pull the protection. Try to ensure that there is a minimum of movement between the moment of removing it and directly gluing it onto the screen. This is necessary to prevent dust from accumulating on the adhesive part.

This completes the installation. Now you know how to glue glass on an iPhone, and you can install a protective surface on your favorite gadget yourself. This technique is relevant not only for the iPhone, but also for any other smartphones. However, you often have to perform one more simple step - remove air bubbles from under the protective surface if they have formed. It's very easy to do. Take a cloth and carefully, pressing the glass where bubbles form, push them to the edges of the screen. Sometimes a small difficulty arises - not only bubbles form under the accessory, but also dust particles. This problem is also easily solved. Usually, a special mini-sticker is included with the glass to remove dust particles. Take it, carefully lift the protection where the speck of dust is located, and remove it with the sticker. Just apply it to the speck of dust, it will stick, and then remove it. If your glass does not come with such a sticker, it’s okay, you can use regular stationery tape. But, it is important to use only regular transparent adhesive tape, and not electrical tape or masking tape. The latter leave behind a sticky layer, so you will have to remove the part and clean the screen again.

How to stick glass on an iPhone?

Additional protective glass for your phone is modern alternative conventional films for screens. This accessory will protect your smartphone from all types of mechanical damage to the display (scratches, abrasions, cracks from dropping the device).

If you decide to purchase a protective glass for your iPhone, check out the basic tips for choosing this accessory:

• The thickness of the glass determines the level of protection of the phone from falls and shocks;
• select the type of glass - matte or glossy. The second option is cheaper. Glossy products protect the screen from impacts, but not from scratches;
• Frosted glass completely protects your iPhone from bumps, abrasions, drops and glare.

Installing a protective accessory on your phone screen does not require special skills. Let's take a closer look at how to stick protective glass on an iPhone in a few simple steps.

Step 1: Clean the display

Bring workplace in order. Make sure there is no dust on the surface that could end up trapped under the film. Then open the package and place all the elements on a clean, flat surface.

Clean your smartphone screen using a cloth and glass cleaner. Carefully wipe the surface of the display and wait for it to dry completely. This action will remove even invisible dust particles. Try not to touch the iPhone screen directly anymore, so as not to create new stains and specks of dust. Wipes for initial cleaning of the phone are included with the protective glass.

Step 2. Unpacking the protective glass

The next step is to unpack the accessory and prepare it to stick it on your phone. Take the screen and disconnect protective layer, which, after sticking, will come into contact with the phone display. After removing the protective layer, try not to touch the protective glass, otherwise fingerprints will remain on the product.

Step 3. Gluing

Turn the protective glass over to the side that was removed from the film. Place the accessory above the smartphone screen without touching it. Try to match everything as evenly and accurately as possible to avoid uneven gluing.

Further action must be done very quickly. Gradually apply the glass to the iPhone display in the direction from the top of the case to the bottom. Release the film so that the side sections stick to the phone themselves. By cleaning the display well, bubbles will not form.

Step 4. Smoothing the surface

Users do not always know how to stick glass on an iPhone. As a result, the result may not be ideal. To remove small bumps or trapped air, take a piece of microfiber (included with the glass) or a clean cloth and gently wipe the phone, moving from the center of the display to the sides, pressing lightly. In this way, flaws can be eliminated.

A film is also glued to the outside of the protective glass. Remove it immediately after all defects have been eliminated. Now turn on the device and check the responsiveness of the sensor. Fine, additional screen should not affect the smartphone in any way.

Eliminating errors

If too many dust particles and dirt get under the protective glass during gluing, it will be inconvenient to use the smartphone. The sensor may respond less well to touches, and appearance such a phone will not be the best. Many users are wondering how to re-glue the glass on an iPhone and is it possible to do it at all? Yes, you can.

If the accessory does not stick properly the first time, carefully remove it from the display and set it aside on a clean surface. Thoroughly wipe the iPhone screen again and make sure there is no more dust or dirt on it. Only after cleaning the screen, stick the glass again. There is no need to peel off the accessory anymore.

How to remove glass from iPhone?

As a rule, users only need to remove the protective glass in one case - when it breaks during a fall or impact. It is very important to remove the accessory correctly so as not to damage the main display of the smartphone with fragments.

Take a plastic card and use it to pry the edge of the protective glass. Then slide the card under the glass until it is completely removed. This method allows you to create some kind of barrier while waiting for the display and a damaged protective accessory.

Any DIY instructions iPhone repair You can find it on our website, or call a specialist for to any place convenient for you.