Instructions for connecting the router. Home wi-fi network
Access to the Internet can be obtained via an Internet cable or Wi-Fi router. In the second case, the connection speed is much higher, and the amount of data transferred is not limited.
A router, also known as a router, works as follows. A cable is brought into the room, which is connected to the router, and then pulled to the computer. The router processes the signal and transmits it to all devices over the air. Most routers are pre-configured at the factory. The user can only connect the device to the PC and use the Internet.
The device memory contains a routing table. It contains paths to all devices. This is how a whole network is formed. Periodically, the router sends messages to each device to see if the signal reaches it. This is how the current state of the routing table is checked and dynamic routing works. To prevent the signal from going to someone else's device, specific addresses are specified. Static routing is more difficult to control if there are many devices connected, but it is more secure.
What you need to connect your router to your computer or laptop
To connect a Wi-Fi router to a computer you need:
- the router itself; network cable; PC, laptop with a network card.
Modern devices are equipped 4 LAN connector. That is, you can connect 4 computers to one device or form a local network. The cable usually comes with the router, and the card is integrated into the motherboard.
How to connect a router yourself
Typically, the installation of the device is carried out by employees of the provider company. But beginners can also connect a Wi-Fi router to a computer on their own.
The equipment kit includes a router, cable and instructions. The first step is to connect the Wi-Fi router to your computer. Since the included cable is quite short, you need to install the router close to the computer. If necessary, you need to order a longer cable from the store and crimp it.
First you need to connect the power cable from the outlet to the device. Next, connect the provider cable and the cable from the computer.
The final step is to insert the network cable into the PC socket.
One end of the network cable must be connected to LAN connector(yellow) to the router, and the second to the computer or laptop.
One of the 4 indicators on the device should light up.
The connection should appear on the taskbar of your PC screen.
How to correctly configure a wifi router
Once the connection is established, you can start setting up.
For one PC
If you connect Wi-Fi router to the computer failed, then the toolbar will light up red cross.
The first step is to simply change the cable. If the connection status has changed. for example, on yellow cross, then that’s where the problem lies.
Most often, difficulties arise due to the fact that network card disabled. To fix this error you need to " Toolbars» select the item « Network and Internet", and then " Network connections" “” will be displayed among the icons. Right-click on the shortcut and select “ Turn on».
If there is no such shortcut at all, then on the PC driver not installed. It is best to download the driver from the disk that came with the equipment.
For PC and mobile gadgets
You can also set up a connection on a laptop through the toolbar. An Internet connection icon is displayed in the lower left corner. Click on it and go to the section “ Network and Internet settings" Available devices will appear in the list. You need to find the name of the router on the network, click on the shortcut and press the “ Connect" If the connection is secure, the system will ask for a login and password.
The connection on a smartphone is configured in the same way. In your phone settings you need to select a section WLAN, find the name of the wireless network in the list, and then enter login And password.
How to install a new router instead of an old one
First you need to connect the new router to the PC, as described earlier. If the device has already been configured by the provider, then the Internet will work immediately after connecting the cable. To check, just open the browser and load the site pages. But if you replace an old device with a new one, you most often have to change the settings.
After connecting the network cable, you need to open your browser and type “ 192.168.1.1 " or " 192.168.0.1 » and press Enter. One of these IPs will open the settings. If none of them worked, then the instructions for the router should indicate the correct IP.
If everything is done correctly, a settings entry window will appear in the browser window. The system will ask for a login and password. When connecting for the first time, you should specify “ Admin" Instead of password a combination may be used 1234 . Also, the login and password for the system can be specified in the instructions for the router.
If none of the suggested options worked, you couldn’t open the settings, then your connection needs additional settings. Only the provider company can understand this issue. Exact settings vary by device model and service provider. There is no universal instruction for such cases.
The settings menu contains several items. The fields should be filled out according to the instructions for your device. It is very important to come up with a strong password. Its length must exceed 7 characters. A strong password consists of Latin letters And numbers.
Passwords and limited access when sharing the Internet
The router itself does not provide access to the World Wide Web. It must be pre-configured and connected to the provider's network. At this point, the problem may arise due to limited access.
If the network cable is connected, but the adapter does not work, there may be several reasons:
- The router is not configured correctly; the drivers are out of order; the wireless network is not configured.
In the next menu you need to select “ Internet Protocol Version 4 (TCP/IPv4)».
In line " IP address» must be entered manually subnet address, which is indicated on the sticker at the bottom of the case.
Now let's look at how to remove restricted access to Windows 8 PC. To solve the problem, you need to reboot the network adapter. To do this, in the “” command you need to enter the line ncpa.cpl.
A list of available connections will appear on the screen. We find the one we need and open the context menu RMB. In the drop-down menu, select the item “ Disable", wait until the adapter changes color to gray, and then connect the device again. Another reason for an incorrect connection may be an incorrectly entered network login and password. To resolve this problem, you should contact your provider.
Nowadays there are a huge number of different Wi-Fi routers from different manufacturers on sale. And that’s good, there’s plenty to choose from. But immediately after purchasing a router, we need to install, connect and configure it. And if the connection process is practically the same depending on the model, then the setup process itself and the page with the router settings can be different even from the same manufacturer.
It is very difficult to give detailed and step-by-step instructions on setting up different models in one article. But I'll try. In this article I will describe in detail and show how to install and configure a Wi-Fi router. Regardless of what manufacturer and model you have. This universal instruction is suitable for both setting up a new router and re-configuring it. You can do everything yourself. And you don’t have to pay specialists for setup.
Login to the router settings. How to log into the web interface?
Each router has its own web interface (site with settings, control panel), which can be accessed through a browser by going to the appropriate address.
Important! To go into the router settings and configure it, your device (PC, laptop, smartphone, tablet) must be connected to the router via cable or Wi-Fi network. At the same time, there may be no access to the Internet on the computer. You don't need internet to log into the control panel!
If you have a high-speed connection on your computer (maybe with your provider's name), then after connecting through the router there is no need to start it!
To enter the settings we need find out the address our router and factory username and password for authorization. This information is located on the body of the device itself. It looks something like this:
On a computer or mobile device that is connected to the router, open a browser (Opera, Chrome, Yandex.Browser, etc.) and go to the address indicated on the case. Or try 192.168.1.1 and 192.168.0.1.
Important! We enter the address in the address bar, and not in the search bar. Many people get confused and instead of a page with settings they end up on a page with the search results of some search engine.
On the login page you need to specify a username and password. The factory settings are indicated on the device body. Most often these are admin and admin. On some models, the default settings are not protected, and immediately after logging into the control panel, you need to set a login and password.
Articles that may be useful to you at this stage:
If the settings page has opened, we can continue. If not, then see the article with solutions to this problem at the link above.
How to set up a Wi-Fi router?
In order to use the Internet through a router, you need at least:
- Set up an Internet connection.
- Set up a Wi-Fi network.
In most cases this is enough. I also recommend changing the password that protects the router’s web interface. There are also settings for IPTV, USB drives, parental controls, etc., but not everyone needs them.
In the control panel of almost every router there is a so-called “Quick Setup Wizard”, also known as “Quick Setup”. On some devices, it opens immediately after logging into the control panel. With its help, you can configure your Wi-Fi router step by step. Internet connection, wireless network, etc. For example, what it looks like at TP-Link:
You can try it, it's very convenient.
Internet setup. The most important step
The main thing is correctly configure the router to connect to the provider. If he cannot connect to the Internet, then all devices will have a “No Internet access” connection. Many users who try to configure everything themselves most often encounter problems at this stage.
Each Internet provider uses a specific type of connection. Dynamic IP (DHCP), Static IP, PPPoE, L2TP, PPTP. This type of connection must be specified in the control panel of the router, and certain parameters provided by the Internet provider must be specified.
Important! You must know exactly what type of connection your provider has. Also all the necessary data for connection (Username: Password), if they are necessary. As a rule, this information is specified in the contract that you received when connecting to the Internet.
Some providers bind by MAC address. It would also be desirable to clarify this.
If your provider uses a “Dynamic IP” (DHCP) connection, then the Internet should work immediately after connecting, since this type of connection is set by default on routers.
If the Internet through the router is already working (and you haven't run any connections on the computer), then you can skip this section and go straight to setting up Wi-Fi.
When the connection type is PPPoE, L2TP, PPTP, or Static IP (which is very rare), then you need to set the necessary parameters. Usually, this is the login and password that your provider gave you. In the control panel, the section with these settings is most often called: “WAN”, “Internet”, “Internet”.
For example, what the PPPoE connection setup looks like on an ASUS router:
Other examples:
Target: so that the Internet through the router works on all devices. Via cable and Wi-Fi. If this does not happen, then there is no point in continuing the setup.
You can always call the provider and clarify what parameters should be specified and where. They help many people over the phone.
Articles that may be useful to you:
I hope everything worked out for you.
Changing Wi-Fi network settings
I highly recommend changing your Wi-Fi network name and password. It is also advisable to set your region. Everything is simple there. This can be done in the section with wireless network settings. It can be called differently: “Wi-Fi”, “Wireless network”, “Wireless”, “Wireless mode”. If you have a dual-band router, then the settings must be set separately for the network at 2.4 GHz and 5 GHz.
- In the "Network name" (SSID) field you need to enter a new name. In English letters.
- In the "Password" field (wireless network key) create and write down a password. Minimum 8 characters. Security type - WPA2 - Personal.
- Well, there should be a “Region” field there. Change it to yours. IPTV on ASUS routers.
If something doesn’t work out for you during the setup process, you can always reset the settings to factory defaults and try setting everything up again. Find the “Reset” or “Reset” button on the case, press it and hold for about 10 seconds. The indicators will tell you when the reset occurred.
You can leave questions in the comments. I just have a small request, describe the problem in detail. Write the router model. Otherwise, it’s very difficult to understand and advise something when you don’t understand the question itself. Best wishes!
The Internet has become an integral part of life, and every computer should have access to the network. At home, a connection via a Wi-Fi router is suitable for this, which provides the ability to use both a wireless connection (for laptops, mobile phones, tablets) and a cable connection (for desktop computers).
Where is the best place to install a Wi-Fi router?
For those who are considering options for how to install a router, you should start by choosing a location to place the device. This is influenced by several factors:
- location of the provider's modem or cables, if used;
- apartment layout;
- location of the desktop computer (if any).
There are different models of wireless devices from Asus, TP Link, D-Link, etc. They may have different data transfer rates and coverage areas. This should be taken into account when you choose a location for the device, so that access is available anywhere in your apartment. In this case, the best solution would be a central point, if the cable, location of the modem and desktop PC allow it. If you have to install the device closer to the computer in order to run a cable to it, then you need to focus on this factor.
How to connect a router to a computer or laptop
It’s easy to figure out how to connect a Wi-Fi router to a computer. The process itself is quick, but problems may arise with setting up the device. Separately below, we will consider the option of connecting a desktop PC via a wireless network and using a network cable. The option of how to connect a router to a laptop is practically no different. Before purchasing a receiver, you should keep in mind that there are models on the market that do not support Wi-Fi distribution and act as an adapter (for connecting several devices).
At the first stage, to gain access to the Internet, you need to correctly connect the wires to the device. There are several major router manufacturers, but the connection diagram always remains the same. Here are step-by-step instructions on how to connect a wifi router to a computer:
- Unpack and install the device, plug it into a power outlet. On the back panel, as a rule, there is a button to turn on the device: press it. If a signal is received, the lights on the router will light up.
- There are several sockets on the rear panel. One of them is always located on the edge and is painted in a different color (blue, yellow) with the signature WAN. Connect the wire from the modem or the Internet cable into it. You should hear the latch click, indicating that the cord is securely secured.
- If you need to connect a cable to the PC, then insert it into any of the empty sockets nearby and stretch it to the connector on the network card. When connected, the light should light up, which means there is a signal.
- When connecting wirelessly, you need to go to the network settings on the PC itself.
Wireless router connection
Most users are interested in the option of how to connect to a router wirelessly. In the case of a laptop, everything is much simpler, because it has a built-in module for receiving a Wi-Fi signal. When it comes to regular PCs, the situation is somewhat more complicated, because you will additionally need to purchase an adapter for a Wi-Fi network. They are easy to find in any hardware store and are often sold together with modems.
There are two options for Wi-Fi adapters for PCs on the market – external and internal. The first ones are connected via a USB cable and stand on the table; they look like a docking station for an Apple player. The latter are mounted on the motherboard via a PCI connector. They work equally well, but the external version can be disconnected and connected to another device, and the built-in one does not take up space on the table. A disk with drivers and software should come with the device.
After connecting to the computer, setup occurs in exactly the same way as on a laptop. In most cases, to enable Wi-Fi on your computer, you just need to find your connection in the list of networks and enter the password. If you are connecting for the first time, you may need to specify the settings that were given to you when concluding a contract with the provider.
Wired connection using twisted pair
Previously, there was only one way to connect a wifi router to a desktop computer - a cord. At first, a cable from a telephone line was used (sometimes still used), then others appeared that provided not only the computer with Internet access, but also the TV with cable channels. This connection method is still used today, as a rule, for stationary PCs. How to connect a computer to a router via cable:
- connect the provider’s wire to the wi-fi router into the socket labeled WAN or Internet;
- The power cord should be inserted into one of the LAN connectors;
- the second end of the cord must be connected to the Ethernet port of the computer, after connection the light should light up (blink).
What to do if the router does not connect to the Internet
Even if you know how to connect a wifi router to a computer and have done all the necessary manipulations, a situation may arise that a connection to the Internet is not established. At the same time, everything works correctly through the cable, and the wireless network does not transmit data, but is visible in the list of connections. If you call the provider’s support service, the first thing the specialist will do is to unplug the Wi-Fi device from the socket, wait 3-10 minutes and turn it on again. In many cases this really helps.
If this method does not help, then there is a high probability that the computer cannot automatically obtain the IP or DNS address of the network. To check the settings, you need to right-click on your connection, select “Network Center”, click on the image of the network connection and go to the “Details” tab. If the DNS or IP item is empty, then this is the problem. You need to call support and find out what values need to be entered in the properties. After receiving them:
- Click on the connections and click on the “Properties” button.
- Find the item that ends with TCP/Ipv4. Click on it and click "Properties".
- Activate the “Use the following IP address” items, enter the data provided to you by your provider.
- Repeat the same for DNS gateways.
- Click "Ok" and close the other tabs.
Video instruction: how to connect a router to a computer
Save your settings. Be sure to restart your Wi-Fi router. Make sure the network connection and wireless access point lights are on. Disconnect the laptop cable from the device and connect to your new Wi-Fi network.
Video on the topic
Sources:
- install router
If there are several computers or laptops within one apartment, then users prefer to combine them into a local network. In addition, the main purpose of creating such a network is to provide Internet access from all equipment.
You will need
- Wi-Fi router.
Instructions
Let's first determine the type of local network you will create. Everything is calculated very simply. If you will only be connecting desktop computers, then it makes the most sense to use a wired network. If the local network will include both computers and laptops or only laptops, then create a wireless or combined network.
Depending on your decision, purchase router or Wi-Fi. As an example, we will look at creating a combined network using Wi-Fi router well, because its setup includes all possible items.
Buy this device and install it in your apartment. Connect all desktop computers to it using network cables. To do this, use the Ethernet (LAN) connectors in router e.
Connect the Internet connection cable to the Internet (WAN) connector. Turn on one of the computers connected to router y, and launch a browser on it. Enter the Wi-Fi IP address into its address bar router A. If you do not know it, then study the user manual.
Find the Internet Setup Settings menu and open it. Fill in the required fields as recommended by your provider. You can obtain more detailed information from technical service specialists. Save. You have already created a local network, and all computers connected to router y, got access to the Internet.
Now let's set up the wireless network. Open Wireless Setup Settings. Enter the SSID (name) and password (password). Select security and radio signal types from the available options. Save changes and reboot router. Make sure you have a wireless access point and connect all your laptops to it.
Video on the topic
It is not surprising that many owners of several laptops and computers want to connect Internet to all of the above devices. This can be done even if your provider provides ADSL Internet services.
You will need
- Wi-Fi router, splitter.
Instructions
Before purchasing a Wi-Fi router, find out the specifications of your laptops. Pay attention to the types of security and radio signals they work with. Naturally, you need a device with a DSL connector to connect to the Internet.
Open the “Software Version” menu (Main Interface), click the “Update” button and specify the path to the downloaded files. Now go to the “ ” (Internet Setup) menu. Change the server connection settings to those recommended by your provider.
Save the applied settings and reboot. Connect all laptops to the created access point, and computers to the Ethernet (LAN) ports. To provide access to the Internet, the Wi-Fi router must be turned on and connected to the telephone line. Unplugging the device will not reset it.
Video on the topic
To create a home local network in such a way that all devices included in it have access to the Internet, it is recommended to use routers. If your provider provides DSL Internet services, then purchase a router with the appropriate port.
You will need
- - network cable.
Instructions
If you do not plan to create a large enough local network, you can get by with a relatively cheap DSL router, for example D-link DSL-2500u. Buy this equipment. Please note that it does not support wireless devices.
Connect the purchased DSL router to the power supply. Turn on your device. Connect the splitter to the telephone line. Connect the ADSL port of this device to the DSL link of the router.
Open Network and Sharing Center. Select the "Change adapter settings" menu. Right-click on the network card connected to the DSL router. Select Properties. Proceed to setting up the TCP/IP protocol. Activate the “Obtain an IP address automatically” option. Save your settings.
Launch any installed browser. Type the following command in its address bar: http://192.168.1.1. Press Enter. When the login and password entry window opens, enter the word admin in both fields. Activate the “Save password” option and click OK.
Open the WAN menu. Specify the required VCI and VPI values. In the Service Category field, select UBR without PCR. Click the Next button to move to the next settings item.
Select the PPPoE data transfer protocol and click Next. Enter the login and password given to you by the provider’s specialists in the special fields. Highlight Keep Alive.
In the next menu, activate the Enable Firewall, Enable NAT and Enable WAN Service items. Save the changed settings. Reboot your DSL router. Connect the required computers and laptops to the LAN ports.
If the provider you choose provides DSL Internet services, then you will need an appropriate modem. In case you need to connect several computers to this device, you can use either a multiport modem or a network hub.
You will need
- - DSL modem
Instructions
If you already have a single-port DSL modem, then purchase a device that will allow you to connect several computers to the modem. In this situation, you can get by with a hub that does not have the ability to configure ports. Using a network cable, connect the LAN port of the network hub to the Ethernet (LAN) connector of the modem.
Now connect the DSL connector of the modem to the telephone line cable through the splitter. Connect all computers to the LAN ports of the network hub. Turn on one of the selected PCs.
Launch your Internet browser and go to the DSL modem settings web interface by entering its IP in the address bar. Open the WAN menu. Select the data transfer protocol type supported by your ISP. Specify the option for obtaining an IP address (Dynamic or Static IP). Enter the required data to obtain authorization on the server.
Save the settings and reboot the DSL modem. Now open the advanced network (LAN) settings menu. Enable NAT and DHCP functions. They are needed to automatically issue IP addresses to computers and to ensure their access to certain Internet resources. Repeat the procedure to reboot the DSL modem.
Open the list of network connections. Proceed to configure the network card connected to the hub. Select TCP/IP protocol properties. Check the boxes next to the “Obtain an IP address automatically” and “Obtain a DNS server address automatically” options. Save the network adapter settings.
Carry out a similar procedure by changing the settings of the network cards of the remaining computers. Open the modem's web interface and click the Connect button. Make sure that Internet access is available on all computers connected to the network hub.
One of the key stages in creating a home or office computer network is installing and configuring a. If you follow the instructions included with this device, the entire job can be completed fairly quickly.
Instructions
The router is designed to distribute the signal between fragments of a computer network or individual computers. Connect one end of the network cable to the modem and the other to one of the router's connectors. The name of the connector (WLAN, WAN, etc.) depends on the specific model. Make sure both the modem and router are connected to power. Some router models come with a disk with special software that is installed on the computer. If there is such a disk, install the programs available on it; they are designed to configure the device.
Establish a connection between your computer and router. If this is your first time making this connection, use an Ethernet cable so you can set up a wireless network. To connect, use a network cable, one end of which is connected to the Ethernet connector of the computer, and the other to one of the router ports marked 1, 2, 3, 4, etc.
Open your browser and enter the router's IP address in the program's address bar. As a result, a page with the router settings will open. Enter your login and password to access the settings; they should be specified in the documentation for the device. The IP address depends on the device manufacturer, for example:
D-Link - 192.168.0.1
Linksys - 192.168.1.1
Netgear - 192.168.0.1
3Com - 192.168.1.1
Belkin - 192.168.2.1
In some cases, the router address is indicated on the packaging box or instructions. If it is not listed anywhere, visit the manufacturer’s official website and use the support service.
Setting up an Internet connection is usually done automatically. The router receives all the necessary parameters from the modem. To set up a Wi-Fi connection, go to the wireless connection settings section. Find the SSID field and enter a custom network name into it, make sure the Enable SSID Broadcast checkbox is checked. The remaining parameters can be left unchanged.
To connect to the network you created, the user will need to enter a password on their device. To protect your connection, create a complex password consisting of a random sequence of letters and numbers. In addition, be sure to change your login and password to access the settings of the router itself, this will prevent unauthorized changes to the network settings.
Video on the topic
A Wi-Fi router, or router, is a network device that acts as a gateway between computers and a high-speed modem. A Wi-Fi router is also a wireless access point to the Internet. To set up this device, you must establish a connection to your modem and computer.
You will need
- - computer;
- - high-speed modem;
- - Wi-Fi router;
- - 2 Ethernet cables.
Instructions
Unplug the modem and connect it to the router using an Ethernet cable. Use the Internet or Modem port on the back of the router; it is usually located next to the power port and is highlighted with a color or label. Remove the cable between the modem and computer, if it was previously installed.
Turn off your computer. Get another Ethernet cable. Connect one end of it to the network connector on the back panel of the computer system unit. Connect the other end of the cable to one of the numbered ports on the router. It doesn't matter which port you choose.
Connect the modem to the power supply and turn it on, wait until the modem establishes a connection with the server of your Internet provider, this may take 1-2 minutes. The success of the connection will be indicated by indicators on the front panel of the device. Connect the router to the power supply and turn it on, wait until the router establishes a connection with the modem; the successful connection is indicated by the lights on the front panel of the router. Now turn on your computer. Connect the devices in this order, otherwise you may not be able to connect to the Internet.
Open and enter the router's address in its address bar. The router's IP address can be found in the documentation for the device or on the manufacturer's official website. As a result, you will be taken to the router settings page. To access the settings themselves, you will need to enter your login and password. Most often, the word admin is used as a login, and the word password is used as a password. The password field can also be left blank. For exact information about login and password, read the documentation for the device.
If you decide to install wi-fi at home, at work, or in any other place, then you definitely need to purchase a special device called a router. This is a special device that distributes wireless Internet at a certain distance. Routers are classified by power, number of connected objects, speed, range, etc. Therefore, if you want to purchase a router, be sure to check out its specifications. Once you purchase this device, you will need to install it. I am sure that 99% of users will have problems with this, so this article is dedicated to how to install a router.
How to install a router - step by step guide
There are a huge number of routers from different manufacturers, but the most popular are D-Link. That is why we will figure out how to install a D-Link wi-fi router.
1) Open the box with the purchased device, take it out and connect it to the power supply. The lights on the front should light up. If they do not light up, then there is some problem with the router. On the back side we see several ports. We need a port labeled “Internet”, into which we must insert the plug that was connected to the computer.
2) In any of the other ports we place the cable that was included with the router. This cable needs to be connected to the computer (to the place where we pulled out the Internet cable).
3) Open any program that provides Internet access. We write the following numbers: 192.168.0.1. This page is the main settings page. You don't need an Internet connection to connect to it.
4) We continue to figure out how to install the router. We have opened an authorization page with the fields name and password. In the name field we write admin, and leave the password field empty.
5) On the page that opens, select the Setup item, then the Internet Setup item on the left and then click Manual Internet Connection Setup.
6) In the Internet Connection Type section that opens, select the item called PPPoE user name/password and select the Dynamic PPPoE item. In the Name, Password and Password Confirmation fields, enter the data that is specified in the agreement with your Internet provider.
7) Look a little lower and see the “clone mac address” item. Click on it. In the Connect mode select item, put a dot opposite Always. The remaining items do not need to be changed.
8) Discussion on how to install is almost complete. All that remains is to figure it out. In the device menu, which is on the left, select the Wireless installation item, then the Manual wireless connection setup button will appear in the center, click on it and look at the main settings menu that opens. In the Wireless section, check the box next to Enable wireless network, and in the Wireless network name field, write any name. We also fill in the Wireless Network Key field and remember it. This field will store the password for your wi-fi. It is needed to prevent neighbors and other strangers from connecting to the router.
I hope that after reading this article, you have figured out how to install a router.