Dre 5000 recovery firmware 3.0.15. Using a USB storage device


- (not official!) - This software is developed on the basis of the official 3.4.369 (the one that will flow from the satellite 07.10.13.) The main difference between this firmware is not shown advertising banners when changing channels. Works stably.

Features of this firmware:

    2 - the submenu search for tricolor TV channels has been removed from the main menu (but it is still available in the menu >> settings >> automatic search>> search type >> tricolor TV) or when initial installation(reset to factory settings)

    3 - when entering the main menu or the game menu, the picture does not disappear!

    4 - in the main nenyu the frills on the side were removed (in my opinion it was not harmonious :))

    5 - exit from the channel list is organized by double click OK buttons (exactly the same as it is organized in 99% of all tuners)

    6 - when you pressed the game button, a swastika was displayed, searching for tricolor channels is now like a proper swastika of the game :)

    7 - the algorithm of the EPG menu has been changed - now it is much more convenient (everything can be done with just one button ok)

    8 - in the Tetris menu the ok and up buttons have swapped places

    9 - possible, but not guaranteed!!! The cause of freezes in receivers with 11 series modules has been eliminated.

    10 - the firmware has already collected the current channels as of 10/05/2013, all garbage has been removed!!!

Past releases

The procedure is quite simple and does not require special skills from subscribers; you just need to follow the instructions for replacing the software from the info channel. The update process takes some time and you need to be patient and wait for it to finish. But despite all the warnings, some users do not wait for the software update process to complete and, as a result, the receiver stops working.

Practice shows that in very rare cases, even after waiting for the software update to complete, the receiver may not turn on after a reboot. There is only one diagnosis - a software update failure.

But don't despair. You can fix this yourself and at home, if you have a computer or another similar working receiver at hand. Below is how to do this. Helps in 99% of cases of unsuccessful software update from satellite.

Software update from a computer.

1. We purchase / solder ourselves null modem cable

2. Disconnect the receiver and computer from the network.

3. Connect the RS232 input of the receiver to the COM port on the computer.

4. Turn on the computer.

5. unpack and install the program

6. and unpack the required firmware receiver:

7. Launch the program (the shortcut should appear on the desktop).

The following window will appear.


8. Click the Open File button and select the downloaded file with the firmware in the window that opens, having previously unzipped it.

9. Click on the Upload button, connect the receiver to the network and turn it on Power button behind the receiver.


10. The progress bar for the File uploading process will begin to show the % and time remaining until the software download process is completed.


In this case, the digital display of the receiver will display the letter L (Load) and the % of the process completed.


11. After this, the progress indicator of the Burning process will begin to show % and the time until the end of the process of burning (firmware) software.


In this case, the digital display of the receiver will display the letter b (burn) and the % of the process completed.


12. The software update process is completed. Turn off the receiver and computer. Disconnect the null modem cable.

Record ID: 35 does not exist!

Software update from the receiver (using the example of DRE 5000).

For DRE 4000, DRE 5001, DRE 7300 the process is similar.

1. We purchase / solder ourselvesnull modem cable.
2. Disconnect the receivers from the network.
3. A working receiver must be connected to the TV. The problematic receiver does not connect to the TV.
4. We connect both receivers with a null modem cable.

The picture above shows a working receiver. Below is a problematic receiver.
4-2. Turn on the working receiver.
4-3. Enter the menu and select Settings.

5. Enter PIN. The default is 0000 (four zeros).

6. In the Settings menu, select Data transfer.

7. A window will appear:


Press the blue button on the remote control.
8. Two scales appear. And the Data Processing scale will begin to fill.


9. When the jackal’s data processing reaches 100%, the following message appears:


10. Turn on the non-working receiver - plug it into the network and turn on Power on the back of the receiver.
11. The filling of the lower scale has begun.


The indicators of the receivers will display the progress of the data transfer/download process in % (on the display there is a symbol L – Load, loading, on the lower receiver, 5 – transmission, on the upper receiver).


12. After this, the following will appear on the TV:


Do not turn off the receivers!!! The process of writing firmware to the (faulty) receiver being flashed begins. In this case, the process will NOT be indicated on the TV screen. The indication process is visible on the display of the receiver being flashed (on the display there is a symbol b - burn, on the lower receiver).


13. We are waiting for the indicator on the receiver being flashed to reach 100%. Afterwards, the receiver being flashed will reboot and the display will show the following:


14. The firmware process is completed. Using the remote control to the question “Data transfer complete. Repeat?" select “NO”. Turn off the receivers and disconnect the null modem cable.

All receivers that work with the Tricolor operator must be updated regularly. This is due to the fact that the company periodically improves its software and keeps up with the times.

Updating the Tricolor receiver via satellite is convenient, does not require special skills, but takes certain time. New updates to the set-top box software are recognized to improve quality software interface, add new features and eliminate possible failures associated with errors in previous software versions.

As soon as new software is released for certain brands of Tricolor television set-top boxes, the company informs its viewers on the information channel.

Updating the receiver via satellite

The process of flashing or updating via satellite is not a very complicated operation and does not require special skills. Just follow the instructions that appear on the Tricolor TV info channel.

Information on the screen alerts the subscriber that updates for specific brands of receivers will be available on a certain day. The following is a warning that during the change process software It is strictly forbidden to disconnect the Tricolor receiver from the network. But for some reason many do not listen to advice, and in the end set-top box stops turning on.

Even if you are patient and still wait for the software installation to complete, there is a risk that your receiver may reboot but will not turn on. There was a problem during the software installation process. This may be due to bad weather or data transmission errors between the satellite and your receiver. What to do in this case, buy a new receiver?

Don’t rush to get rid of the set-top box and buy a new one; it is possible to restore the device’s functionality if you have a computer or another working Tricolor receiver. This method helps in almost 100% of cases of software failure or unsuccessful update.

Firmware firmware from a personal computer

In order to flash the set-top box from a computer, you will need a so-called null modem cable (RS232), which connects to the COM port of the PC.

The procedure can be divided into the following stages:


When the update process is completed, in the DRE Burner program, in the Burning tab, the scale will be filled to 100%.

This means that the software installation process is complete, you need to turn off the set-top box and disconnect the RS232 cable. It is advisable to carry out all actions involving connecting and disconnecting wires with the computer and set-top box de-energized.

The process of flashing firmware from a USB flash drive

If you have a modern Tricolor receiver and your set-top box has a USB connector, you can flash the software without going through all wired connections, that is, directly. It is important that the update process is only possible with a working receiver. If your set-top box stops turning on after an unsuccessful update, or for some other reason, this method will not help you, you need to flash the firmware via the COM port.

The update process consists of finding the latest firmware on the website and downloading it to your computer. Unzip the file and write it to a FAT 32 formatted file USB flash drive. We insert the flash drive into the appropriate connector and turn on the Tricolor receiver. After switching on shell will detect the flash drive, find the latest software on the media and begin automatic firmware.

The inscription “DL” or “L” (depending on the set-top box) may appear on the front panel, which symbolizes that the download process has started. At this time, the following messages will appear on the television screen: “Updating bootloader” - “Cleaning memory sectors” - “Writing image to memory”. During the software download process, it is strictly forbidden to turn off the receiver or unplug it from the outlet.

If, while installing the firmware, you accidentally turned off the set-top box or your lights were turned off, then it will be extremely difficult or even impossible to restore functionality after that.

After the update process is completed, the bootloader will inform you with a corresponding splash screen on the TV screen and the set-top box will reboot.

 To update software via satellite, the receiver must be connected to a configured satellite dish.

PROCEDURE:

1.Unplug the receiver's power cord from the outlet, and then plug the receiver back into the power supply.

2. Switch the receiver to the Tricolor TV info channel.

3. After a few seconds, the following message will appear on the screen indicating the need to update the receiver software:

When of this message select the “Yes” option and press the “OK” button on the remote control.

4. After agreeing to update the receiver software, service messages about the process of updating the receiver software will appear on the screen. Updating the receiver software takes about three minutes.




5. Once the software update is complete, the receiver will reboot and turn on in channel viewing mode.

6. After the software update is completed, go to the “Status” menu and make sure that the receiver software version has changed to 3.4.432.


7. At this point, the receiver software update is completed, and the receiver is ready for further operation.

Video instructions for updating the software of receivers models DRE-4000, DRE-5000, DRS-5001, DRS-5003, DRE-7300 and GS-7300

How to update the Tricolor channel list on DRE-4000, DRE-5000, DRS-5001, DRS-5003, DRE-7300 and GS-7300 receivers

Updating the channel list may be required in several cases:

1. To find new Tricolor TV channels that are not on your receiver
2. After carrying out maintenance work on the satellite
3. When initial setup equipment
4. When changing broadcast parameters (changing frequencies) of some channels
5. Preventively twice a year

To update the channel list, press “MENU” on your receiver’s remote control, select “Search for Tricolor TV channels” => “OK” and update the list of TV channels by following the prompts on the TV screen.

The interface between the user and the hardware is called software. Satellite receivers already at the production stage contain software that includes a minimum set of functions and allows the device to perform the actions indicated in technical documentation. Over time, manufacturers expand the capabilities of the equipment by installing alternative software. To obtain the spectrum additional features Reinstallation of the software is required, therefore, to replace the factory firmware, the subscriber must know how to flash the Tricolor receiver independently. So, firmware of a receiving device is its software, and flashing a device means replacing its software.

Thanks to feedback with Tricolor TV users, manufacturers learn about shortcomings and problems in the operation of devices, work on new versions of software, correcting errors, trying to improve their capabilities. Having learned to perform the firmware on their own, the user will keep pace with the development of the Tricolor TV company. Often new versions of programs are intended for technical department specialists, but in Lately The company's employees make the software freely available. This step allows service centers to be freed from the heavy burden associated with large-scale customer visits.

Depending on the model of the receiving device, the program update processes differ. Each type of receiver has its own methodology, features and programs. The duration of the program rewrite operation usually takes several minutes, while the device changes the old software to the new one:

  • newly installed software eliminates various freezes and other problems;
  • translation into Russian becomes more accurate and correct;
  • The channel list is updated;
  • new functions are added to the receiver;
  • changing the interface to a more convenient reading type;
  • the receiver’s operating speed and sensitivity to remote control commands increases;
  • added the ability to work with external media(reading any media file formats);
  • the ability to record Tricolor TV programs using a timer;
  • the ability of the receiver to access the global network.

Usually, after a new version of software is released, subscribers leave feedback on its performance. Having decided to download new software, you can download the program to your receiver from another device on which new software has already been installed, from a computer, from a satellite, from the Internet or from removable media.

Downloading firmware from a computer

The first step is to connect the receiver to the computer using an RS-232 cable. In this case, the device must be disconnected from the power supply. The computer must have a firmware file and a bootloader program corresponding to the receiver model. Next, according to the instructions, the firmware is installed satellite receiver Tricolor TV. If there is no port for connecting the cable, you should use a special adapter. Once the update is complete, the receiver should reboot. This means it is ready to go.

Installing software from another receiving device

This method requires connecting two devices to each other via the same cable as in the previous method. The installation process is individual in each case. Connection of two different models is not valid, and not every type of receiver supports such a connection.

Accepting an update from the Tricolor TV satellite

This method is the easiest, especially for unprepared clients of the company. A new version The software is transmitted from the same satellite from which the TV channels are broadcast. The receiving device notices the appearance new firmware and displays a message about permission to accept the update. The user confirms the action using the remote control and does not perform any further actions until the receiver reboots.

Using a USB storage device

This method is only suitable for models with USB port. First you need to format the flash drive using a computer or receiver. After that, write to it a file with firmware suitable for the selected receiver model. The finished flash drive should be connected to the receiver and act in accordance with the instructions. The final step is to automatically reboot the device.

Flashing via the Internet

In order to flash equipment in this way, the Tricolor TV receiver must have access to the Internet and have a special port for this. Some experts create world wide web special resources for publishing new software. The receiving device can find such programs on the Internet and ask the user for permission to accept the update. If the receiver is prohibited from making independent exit to the Internet, then the subscriber, using the menu, instructs him to scan resources for new software versions.

Program update rules

To avoid damage to the receiving device, during the program rewriting process it is prohibited to disconnect it from the power supply or carry out any actions with it.

If the firmware is interrupted by the user, the malfunction of the device can be corrected by flashing it using a computer or other receiver. There are several other rules that Tricolor TV users should know:

  • before installation new program you need to read the instructions, which indicate the sequence of actions to be performed;
  • While replacing the software, it is recommended to connect the receiver to the source uninterruptible power supply. This step is provided in case of a power outage and interruption of the update process, since some models of receivers can only be restored using special tools or in service centers;
  • In order to roll back new software in the event of an error or unsatisfactory operation of the program, it is advisable to store archived versions of the software.

If for any reason the subscriber refuses to replace the firmware of his equipment, it is recommended to contact service center. Specialists are always happy to help their clients.


2024 gtavrl.ru.