Apple iPod shuffle won't turn on. Causes and solutions

All tips

Your iPod won't charge and you can't figure out why? Then this article is addressed to you. If your iPod is not charging, it is advisable to immediately stop trying to charge it. Also, you should not try to play your MP3 repeatedly. iPod player. In these attempts, you may be seriously making the situation worse.

For example, if moisture gets into the player, then when turned on and when charging, an electrochemical effect will occur, as a result of which your player will fail even more. As a result, repairs will cost you much more and take more time.

In such cases (when not charging in progress) diagnostics are always necessary. It will help you figure out why it's not charging. iPod Touch 5, 4, Nano 7, 6, Classic, Shuffle. Our diagnostics are completely free.

Why the iPod won't charge, here are some of the most common reasons

1. The connector is faulty. Mechanical impacts of various kinds (player falling, non-compliance with operating rules, incorrect connection charger...) may render the connector unusable. At the same time, it is impossible to repair it at home without special equipment, so the connector needs to be replaced in a specialized workshop.

2. Voltage surges or moisture ingress. If moisture got inside the case or there was a voltage surge, and as a result the iPod stopped charging, then this behavior could be caused by a failed power controller or the lower cable. Our technicians will be able to accurately identify the faulty part and offer best way restore functionality of iPod Touch 5, 4 (4g, 3g). Perhaps this will be cleaning from corrosion, replacing or repairing faulty parts.

3. Also, problems may arise from moisture or mechanical shock when it is not charging from iPod computer. The reason for this may be following problems: damaged power supply, printed circuit board tracks, etc. To accurately determine the breakdown, it is necessary to carry out diagnostics at a service center.

4. Damage to the charging device. When not charging from the mains new iPod, the charger may be faulty. Here we can advise the following: before you start worrying about the breakdown of your iPod Touch, check it with a different charger. You may be pleasantly surprised to find that your iPod begins to charge. In this case, you can just buy a new charger.

5. iPod does not charge from USB. If you long time did not use your player, the battery could be deeply discharged. When turned off, it uses a small amount of power, but over time it will use up all the charge, which can cause the iPod to take too long to charge or fail to charge via USB. To prevent this from happening, you need to periodically charge the player. It’s a different matter when the iPod does not see USB, the problem may be with both the player and the computer. In any case, diagnosis will not hurt.

Important: Promotion! Reduced price by 50% marked with the word “Promotion”, valid until the end of this month 1. How iPhone spare part from a copy; 2. We install original spare parts and provide a 1-year warranty! 3. 20-50% discount at the request of regular customers - see special									Price installation details in our service center:
Name of spare parts	Touch 6	Touch 5	Touch 4	Touch 3	Touch 1/2	Classic	Nano 6	Nano 7	Price installations in rub.
Display (original) Promotion!	3900	3600 Promotion! Promotion until Sunday Sensor+ display	1580 Promotion! Promotion until Sunday	790 Promotion! Promotion until Sunday	750	860	1900 Sensor+ display	1600	190 Promotion!
Touch glass (original)	3900	3600 Promotion! Promotion until Sunday Sensor+ display	1580 Promotion! Promotion until Sunday	790 Promotion! Promotion until Sunday	680	-	1900 Sensor+ display	1750	190 Promotion!
Power connector	450	450	450	450	450	450	450	450	499
Power management chip	1600	1600	1600	1600	1600	1200	1200	1200	1800
Home button (body part)	450	450	450	450	450	450	-	-	499
Home button (inner part: cable with components)	490	490	490	490	350	350	-	350	499
Power button	490	490	490	490	490	490	490	490	499
Headphone cable	450	450	450	450	450	440	450	450	499
Battery	800	800 (with housing and components)	800	800	800	800	800	800	499
Cover (body)	990	990	990	990	990	800	800	800	499
Speaker	460	460	460	460	460	-	-	-	499

Become our regular customer and get a discount on our special.
Service center services
Installation of modules and components: display, speaker, case repair, etc.		from 100-900 rub., from 20-50 minutes
Installation of radio elements: capacitor, diode, transistor, varistor, etc.		from 50-900 rub., from 1 hour
Restoring the printed circuit board (without replacing radio elements)		from 200-800 rub., from 1 hour
Installation of microcircuits, controllers, etc.		from 600 rub., from 1 hour
Recovery after moisture ingress		from 900 rub., from 1 hour
Firmware		900 rub., 40 minutes.
Diagnostics and troubleshooting are free!

It is very difficult to fix the problem yourself:

This is possible only in some cases (the charger is broken, etc.), and is often dangerous, since you cannot be 100% sure of the causes of the breakdown.

Contact us! After a detailed free diagnosis, we will return your player to its original state. working condition. You can also contact us when your iPod Touch 4 (4g, 3g) does not charge completely, does not see USB, or other problems not mentioned above arise. Please know that we sell spare parts all over Russia and because of this, in our workshop there are only original spare parts for the Nano 7, 6, Classic, Shuffle, Video models, and all of them are at the most low prices. It’s also good news that with any repair we will give you a guarantee for the entire device.

A young man approached us. His problem was the inability to charge the player. After diagnostics, it turned out that there was a problem with moisture ingress. Diagnostics and recovery cost him 900 rubles. If he had called later, repairing the iPod would have cost much more.

iPod Shuffle audio players Apple - digital devices for listening to music, playlists, audio files by synchronizing them from the Internet, computer, program iTunes Store. The operating time of the players depends on the built-in battery. Charging all generations of iPod Shuffle is quick and easy.

To find out how long the gadget takes to charge and how to charge it, you need to consider these issues in more detail.

general information

The built-in battery can only be replaced by authorized service centers. Apple Centers. Therefore, the user must be able to operate it correctly. To ensure optimal performance, the battery must be fully charged before using the player for the first time. After 2 hours the charge level will be 80%, after 3 hours - 100%.

The audio player is charged in 2 ways:

connection to a computer;
by connecting to an Apple USB power adapter.

USB cable - a power supply wire with a 3.5 mm plug on one side and a USB plug on the other. Cables different generations similar, but not suitable for charging. Thus, the iPod Shuffle 2 cable cannot be used to charge iPod Shuffle 3 and 4 and vice versa.

When connecting to a computer, make sure that it does not go into sleep mode. It should be noted that some Mac models Support charging in sleep mode.

A color indicator located on the body of the gadget reports the current state of the battery.

Each color corresponds to this level:

green - 26–100%;
yellow - 11–25%;
red - 1–10%;
flashing red - less than 1%;
does not light up - 0%.

IN latest version Apple player present voice accompaniment by using the latest development- VoiceOver functions.

Charging the 1st generation iPod Shuffle

For iPod Shuffle 1, charge as follows:

Determine the battery charge level. On the back of the gadget, find the Battery status key.
To charge via a computer, first turn on the equipment, then remove the cap from the player and insert it into the computer’s USB port.
Using the adapter, connect the gadget to the connector of the AC device, then connect the power supply to the network. When using an extension cord, attach one end of the wire to the AC adapter and the other to the audio player. Plug into a working outlet.

Charging iPod Shuffle 2nd Generation

Battery Apple iPod Shuffle 2 charges like this:

Check the level of discharge of the device in accordance with color scheme status indicator.
Connect the USB cable to your computer or Apple power adapter. To do this, connect the plug of the wire to a high-power USB port of the computer or to the connector of the power supply, and the plug to the connector of the player.
Connect the Apple power supply to the mains.
Check that all devices are connected correctly. The indicator should glow orange during charging and green when finished.

Charging iPod Shuffle 3rd Generation

For the 3rd generation of audio players, you must perform the following steps:

Check the charge, quickly turn off and turn on the device, look at the status of the indicator. On minimum level charge indicator is red.
To connect to a computer, insert the plug of the USB cable into the USB port of the device, and the other end with the plug into the audio player. The computer must be turned on.
Using an AC adapter, the process is carried out in the same way, only the cable plug is inserted into the power supply connector and plugged into the network. Before plugging in, check whether the adapter is assembled correctly.

Charging the 4th generation iPod Shuffle

The 4th generation Apple player charges in a similar way, with the only difference being that the VoiceOver button is used to determine the charge level.

The number of battery recharging cycles is limited. The durability of devices and the number of cycles depend on the operating mode and settings.

The device is supported in operating mode by a built-in battery. Periodically it is necessary to fully charge it. Charging for iPod shuffle is almost the same for all generations. An important stage after purchasing the player is correct input batteries into operation. How to properly charge an iPod shuffle?

The player's built-in battery must be replaced only at authorized service centers. Therefore, it is important to put the device into use correctly. To do this, after purchasing, charge the gadget until it is 100% charged. After two hours of recharging, the player's charge level will be about 80%, and it will be fully charged after three hours. Then use and charge as convenient.

The device can be charged in two ways: using a USB connection to a PC and using a power adapter (purchased separately). The iPod shuffle charger is a cord with a 3.5mm plug and a USB plug at the other end.

When the player does not charge, check the serviceability of the outlet by connecting the adapter to another. If you are using a USB port, try connecting the device to other connectors or to another PC. If changing the socket and connecting to other sockets does not help, contact your service center for diagnostics.

3rd and 4th generations

To find out how long the device should be charged, you need to know its charge level. For the 3rd generation, press the on-off button twice quickly. For 4th generation, double-click VoiceOver. Now connect the gadget via USB cord to PC. During the entire charging time, the PC must be in normal mode(not "dream")

If you are using a power adapter, connect the plug to the 3.5mm jack and connect the cable to the adapter. Connect to an outlet. The charge status indicator will change color as the battery is refilled. Green color indicates a sufficient charge level.

2nd generation

First of all, we check the state of charge in the batteries. To do this, turn on the gadget or connect and disconnect it from the PC. After you have found out how much energy is left, connect the USB cable with one end to the gadget and the other to the PC. The computer must be running; when in sleep mode, no power is supplied to the connectors and charging will not occur.

If you purchased a power adapter for charging, then you need to connect the cord with one end to the 3.5 mm jack and the other to the adapter. Then connect the adapter to the outlet. The charging process is indicated by an orange indicator light. At full battery it will glow green.

You can charge the player using an iPad charger. Take the charger from the tablet and disconnect the cable from its “head”. Insert the cord from the player into this place. Connect one end to the player and the other to the power source.

1st generation

First, find out the battery charge level. To do this, on the back of the player you need to press the Battery status key. Then remove the cap from the player and connect directly via the USB connector to the PC. The USB connector must transmit sufficient energy for power. Check that the PC is not in sleep mode, but working.

If you use a special adapter for power, then connect the player to it in the same way. If you are using an extension cord, connect one end to the player and the other to the adapter, and plug the adapter into a power outlet.

Energy levels

The color the indicator lights up indicates the state of charge. If it glows green, the energy level is between 26-100%. If it lights up orange, then from 11 to 25%. A red indicator indicates that the battery level is very low, ranging from 1 to 10%. When the signal flashes red, the charge level is below 1 percent. When the indicator does not light up at all, the device is completely discharged.

Apple products are durable and have a long service life, but malfunctions and breakdowns are still possible. Users often encounter the problem that their iPod won't turn on and want to know how to fix the problem themselves without spending money on a repair at a service center.

The player shows no signs of life

It happens that an iPod that previously worked without interruption stops turning on. This can happen for no apparent reason or due to the user's fault, for example, if the device was dropped, hit, or stored in inappropriate conditions. Then, when you press the power button or any other button, the screen will remain dark and there will be no reaction from the gadget.

No iPod is immune to this, be it Touch, Shuffle, Nano or Classic. In this case, it is important to find out why the player does not turn on and apply all possible ways troubleshoot the problem yourself.

Causes and solutions

The most common reason that a gadget does not turn on is low battery. This could happen even when the player has not been used for a while. To make the player work, connect the device to a power source and wait a few minutes. The Apple logo will appear on the screen and the gadget will turn on. When charging via a low-speed USB port, the player will start working within 30 minutes after connection. If the player does not turn on after this, make sure the cable is connected correctly or try a different charger.
Does not work power button. If when connecting to charger The battery indicator flashes on the screen, but the player does not turn on, then the problem lies in the power key. This minor problem can be corrected at a service center.
On iPod moisture got in. Penetration of liquid into the device will damage the circuits and contacts, and then the player will neither turn on nor charge. In this case, only a specialist can fix the breakdown. The chance that after repair the gadget will turn on and work as before depends on the severity of the damage.
Impact or fall of the gadget. As a result of this mechanical impact The contacts or cable may have broken, which can only be repaired by a professional. Damaged parts may need to be replaced in order for the player to turn on.
Locking enabled. You can block all buttons, including power buttons, with a switch located at the top or bottom of the case. The lock is activated if an orange dot or stripe appears next to the switch. By moving it so that the point is hidden, you can remove the lock, thereby returning all the keys of the gadget to their functions.

Sometimes an iPod that shows no signs of life will turn on after a factory reset or force restart. You can use it to disable active applications and programs. This does not mean losing files on the player, but it can return some settings to factory settings. How to reset to different models, described below. When the device turns on, you must update immediately software iPod.

Force restart iPod

Sometimes, in order for the device to turn on again, it is enough to force it to restart. In different models Apple devices This can be achieved by pressing different key combinations. To reset your iPod, press and hold the following buttons simultaneously.

1. Force restart iPod Classic

Press the "Menu" and "Select" keys simultaneously for 8 seconds. The lock switch should be in a position where the orange stripe is completely hidden.

2. Force restart iPod Shuffle

The restart is carried out in a state disconnected from the network and the computer by pressing the power button. The green indicator should go out. After 10 seconds the player should start turning on.

3. Force restart iPod Nano

If the iPod Nano does not turn on, the method of forcing a restart will depend on the generation of the gadget:

To reset a 7th generation device, you must hold down the “Sleep/Wake” and “Home” key combination.
Nano 6th generation restarts using the Volume Down and "Sleep/Wake" buttons.
If the device is generation 5 or earlier, you need to press the “Menu” and “Select” keys when the lock is off.

4. Force restart iPod Touch

You can restart the player of this model by simultaneously pressing the "Home" and "Sleep/Wake" buttons. Hold them down for 10 seconds or until the Apple logo appears.

5. Force restart iPod Mini

If the iPod Mini or players with a dock connector and touch wheel do not turn on, force a reboot as follows:

iPod Mini - a combination of the "Menu" and central buttons;
iPods with a scroll wheel, touch wheel and dock connector - Play/Pause and Menu buttons.

All actions must be performed with the key lock turned off (the switch must hide the orange mark). If after the first attempt the gadget does not turn on, you should repeat the action again.

Products Apple Corporation For a long time now it has been famous all over the world for its gadgets, which are distinguished by their high reliability and quality of work.

But with iPod gadgets, like with any other modern devices Even from this manufacturer, sometimes certain breakdowns occur. One of the most common problems is when the iPod Nano of any generation does not turn on.

In most cases similar problem You can solve it yourself, without resorting to the help of qualified service center employees.

Several reasons and methods for eliminating them

There are many reasons why the player may not start.

The most common of them are:

The iPod 5 or other gadget model is discharged, as a result of which it does not turn on. Fixing this problem is very simple - put the device on charge.
The power button is broken. This is very easy to check - if, when you connect the charger, a charging indicator appears on the screen, but the button that starts the gadget still does not respond to pressing, repair will be required. This can be done by specialists in specialized service centers;
Moisture has entered the gadget, which can damage the microcircuits and contacts. As a result, the gadget does not turn on and does not charge. There is only one way out - take the player to a service center, since you can’t do anything on your own;
if the gadget was dropped, this could lead to a break in the cable, contacts or other elements. In this case, as in the previous one, professional repairs will be required.

Turn off the lock switch

Another fairly common reason why a gadget may not turn on is that the lock switch is turned on.

This switch is located on the bottom or top of iPod Shuffle or another model or generation of Apple device.

When it is in the “on” position, an orange stripe appears next to it. In this case, not a single button on the gadget’s body will work, and the power button is no exception.

To disable the lock, the switch must be moved so that the orange strip is completely hidden. After this, you can try to turn on the player again.

Check that the battery is charged

Also, the reason that the iPod Nano 6, like other models, does not turn on is a discharged battery.

To check this, you should pay attention to the screen when you try to turn on the device: when the battery is low, a screen appears on it for 3 seconds, indicating the need to charge.

To charge the gadget, you need to connect it to:

It's worth noting that Shuffle 4 and other generations only require a high-power USB port to charge. iPod nano and 5th generation iPods can charge via FireWire or USB.

In addition, you need to remember that if you charge a completely discharged battery through USB port the delay before turning on can be up to half an hour. Therefore, if you use this type of charging, you can try to turn on the player no earlier than after 30 minutes.

Reset settings

If after all the above, the player still does not work, you should try resetting its settings. No need to worry: this is all user files are saved.

But some parameters may be lost, but returning them will not be difficult.

iPod nano (7th generation)

To reset settings on iPod Nano 7, you need to follow these instructions:

If this does not help, you can resort to your last chance - restoring factory settings. It should be remembered that this will delete all user files, but it is quite possible that such a procedure will eliminate all problems.

If this does not help, there is only one thing left to do - seek help from a service center, where they will definitely restore the Nano 7.

iPod nano (6th generation)

To reset the settings of such a sixth-generation gadget, you need to do the following:

press and hold the sleep button and volume down button simultaneously for 8-10 seconds. This step may need to be repeated. After this, the Apple logo should appear;
It happens that such actions do not produce any results. In this case, everything will need to be repeated, having first connected the player to the network or computer;
If the backlight does not even turn on, it is quite possible that the battery is low. To eliminate this possibility, you should leave the player connected to the computer for about 30 minutes, and then repeat all the above steps.

If this does not help, all that remains is to restore all default settings or immediately take the Nano 6 to a service center, where the cause of the problem will be accurately restored.

iPod with click wheel

If the 1st-5th generation iPod, the main feature of which is the control wheel, does not turn on, then to reset its settings you need to do the following:

Otherwise the device will need full recovery parameters from the manufacturer or professional help service center.

iPod (scroll wheel), iPod (touch wheel), and iPod (dock connector)

To reset an iPod with a touch wheel, scroll wheel, or dock connector, you'll need to do the following:

iPod shuffle

To perform a factory reset iPod Shuffle, you need to do this:

iPod touch

Touch 5 does not respond and does not turn on – what should I do? You can try forced reboot, which also resets the device settings.

To do this you should:

Do a battery drain

Sometimes the player may be in a state where resetting the settings does not give any effect. Why is that? This is due to the characteristics of the device. In this case, preliminary complete discharge batteries.

So, if the player does not turn on after a reset, you need to do the following:

disconnect the player from all power sources for a day;
connect it to the power adapter or computer, repeating all reset procedures again.

Video: Power button does not work

Update your software

If you managed to turn on the player after resetting the settings, it is recommended to immediately install new version Software: After the update it will start functioning normally.

Windows Update

To update the player from a computer running Windows OS, you need to do the following:

From a Macintosh computer

When updating the software iPod software From a Macintosh computer you need to follow this sequence of actions:

connect it to the PC with a USB cable and launch the proprietary iTunes application;
Before starting the update, the player must be formatted from a Macintosh PC, otherwise it will not be possible to install the new version of the software;
iTunes will automatically detect a new version of the software online and prompt the user to download it. If updates have already been downloaded, they will be prompted to install them;
depending on the method of connecting the player to the computer and its model, you may need to connect the device to the power adapter or leave it connected to the PC;
After this, a progress bar will appear on the iPod screen along with Apple logo. When the indicator reaches 100%, the player is ready for use.

Thus, if a popular iPod player of any generation has stopped working or without any visible reasons it stopped turning on - this is not yet a reason to panic.

There are many ways to try to bring it back to life on your own, most of which are described above.

If, even after trying all of them, nothing works, and the player still does not turn on, there is still a way out - you can always contact a service center for help.

Employees of such services will always tell you what kind of repairs the gadget will need so that its owner can enjoy using it as before.